Bosch DS7200V2-EXP Installation Manual page 67

DS7200V2-EXP | Installation Guide | 3. Control Panel
Programming
Area Name Text
• Address:
Area 1 Name: 1394 to 1425
-
Area 2 Name: 1458 to 1489
-
Area 3 Name (DS7240V2 only): 1522 to
-
1553
Area 4 Name (DS7240V2 only): 1586 to
-
1617
• Default:
Area 1: Area 1 Name Text
-
Area 2: Area 2 Name Text
-
Area 3 (DS7240V2 only): Area 3 Name
-
Text
Area 4 (DS7240V2 only): Area 4 Name
-
Text
• Selections: See Key/Character selection chart
All control panel text is programmed from the text
keypad in a special text-programming mode. See
Text Entry Addresses on page 47 for text
programming instructions.
Enter up to 16 characters to describe each area.
Area Idle Text
• Address:
Area 1 Idle Text: 1426 to 1457
-
Area 2 Idle Text: 1490 to 1521
-
Area 3 Idle Text (DS7240V2 only): 1554 to 1585
-
Area 4 Idle Text (DS7240V2 only): 1618 to 1649
-
• Default: Not Ready
•
Selections: See Key/Character selection chart (above)
All control panel text is programmed from the text keypad in a special text-programming mode. See
Text Entry Addresses on page 47 for text programming instructions.
This parameter provides 16 characters of programmable text for each area displayed when the system
is idle (no alarms, no troubles, system disarmed).
If the "Don't Show Zone Status on Keypads" option is not enabled in the Keypad # Options parameter
(page 72), the text keypad displays "OK for All On" or "OK for Perimeter" across the second line. This
indicates that all zones are normal and the system is ready to arm All On or Perimeter Only. If a
controlled zone is faulted, the area idle text for this zone's assigned area replaces the "OK for All
On/OK for Perimeter" message.
If a zone not configured for Perimeter Only arming is faulted, "OK for Perimeter" replaces "OK for All
On" on the text keypad's display. The system might be armed Perimeter Only, but cannot be armed All
On until the faulted zone is restored.
If the "Don't Show Zone Status on Keypads" option is enabled, the area idle text displays continuously
on the second line when the keypad is idle (even if a zone is faulted).
If the "Don't Show Zone Status on Keypads" option is selected, the default Area Idle Text
("Not Ready") should be changed. See Text Entry Addresses on page 47 for text entry
instructions.
Bosch Security Systems, Inc. | 04/12 | F01U253045-02
Ke Character
y
0
+ - 0 * / \ [ ] = > < # §
1
Space . 1 ? ! , @ _ & ~ : ; " ( ) ' ¿ ¡ % £ $ ¥
A B C a b c 2 Å Ä Ã å ä á à â ã α β Ç ç
2
D E F d e f 3 É Æ ë é è ê æ Δ Φ δ ε
3
G H I g h I 4 ï í î ì Γ γ η ι
4
J K L j k l 5 Λ κ λ
5
M N O m n o 6 Ö ö Ñ ñ Ø Õ ø ó ò ô õ Ω μ ν ω
6
P Q R S p q r s 7 Π Σ π ρ σ
7
T U V t u v 8 Ü ü ú ù û Θ Υ θ τ υ
8
W X Y Z w x y z 9 ÿ Ξ Ψ ξ χ ψ ζ
9
* Moves to the address before the
text block.
# Moves to the address after the text
block.
A Moves cursor to the previous
character position in text block.
C Moves cursor to the next character
position in text block.
The following keys are not used in
EN | 67