Bosch Security Systems, Inc. | 04/12 | F01U253045-02 En - Bosch DS7200V2-EXP Installation Manual

DS7200V2-EXP | Installation Guide | Figures
Figures
Figure 1: Enclosure Installation .......................................................................................................... 11
Figure 2: Control Panel Board Mounting ............................................................................................ 12
Figure 3: Standby Battery Connections .............................................................................................. 12
Figure 4: RAM Backup Battery ............................................................................................................ 13
Figure 5: RJ31X/RJ38X Wiring ............................................................................................................ 13
Figure 6: Ground Start ........................................................................................................................ 14
Figure 7: Keypad Jumper Plug Configuration ..................................................................................... 15
Figure 8: Keypad to Control Panel Wiring ........................................................................................... 15
Figure 9: Keypad to Control Panel Wiring (External Power Supply) .................................................. 16
Figure 10: Keyswitch: Tamper Wired Zone Configuration .................................................................... 16
Figure 11: Maintained Keyswitch: Single EOL Resistor Configuration ................................................. 17
Figure 12: Momentary Keyswitch: Single EOL Resistor Configuration ................................................. 17
Figure 13: Keyswitch: Zone Doubled Configuration ............................................................................. 17
Figure 14: Keyswitch: No EOL Resistor Configuration ......................................................................... 17
Figure 15: Tamper-Wired Zone Configuration ...................................................................................... 18
Figure 16: Single Zone Sensor Loop Wiring ......................................................................................... 19
Figure 17: On-board Doubled Zone Sensor Loop Wiring ...................................................................... 19
Figure 18: Single Zone Sensor Loop Wiring (No EOL) ......................................................................... 20
Figure 19: 4-wire Smoke Detector (Tamper-wired) .............................................................................. 20
Figure 20: 4-wire Smoke Detector (Single EOL Resistor) ................................................................... 21
Figure 21: PO 1 Wiring (PO 1 Jumper Shorted) ................................................................................... 21
Figure 22: PO1 Dry Contact Wiring (No PO 1 Jumper) ........................................................................ 21
Figure 23: PO 1 Positive Alarm Trigger Wiring ...................................................................................... 22
Figure 24: PO 2 to PO 4 Wiring ............................................................................................................ 22
Figure 25: RF3227E Address Jumper Settings ..................................................................................... 22
Figure 26: RF3227E to Control Panel Wiring ........................................................................................ 23
Figure 27: Standard DX2010 Installation Locations ............................................................................. 23
Figure 28: Optional DX2010 Mounting Locations ................................................................................. 24
Figure 29: DX2010 to Control Panel Wiring .......................................................................................... 24
Figure 30: DX2010 to Control Panel Wiring (External Power Supply) .................................................. 25
Figure 31: DX2010 Auxiliary Output Wiring .......................................................................................... 25
Figure 32: DX2010 Tamper Input Wiring .............................................................................................. 26
Figure 33: DX2010 No Tamper .............................................................................................................. 26
Figure 34: DX2010 Tamper-Wired Zone Wiring..................................................................................... 26
Figure 35: DX2010 Single EOL Zone Wiring ......................................................................................... 27
Figure 36: DX2010 Doubled Zone Wiring ............................................................................................. 27
Figure 37: DX2010 DIP Switch Configuration ....................................................................................... 28
Figure 38: DX2010 Status LED Location .............................................................................................. 28
Figure 39: DX3010 to Control Panel Enclosure Installation ................................................................. 29
Figure 40: DX3010 to Control Panel Wiring .......................................................................................... 30
Figure 41: DX3010 Output States ......................................................................................................... 30
Figure 42: DX3010 to Control Panel Wiring (External Power Supply) .................................................. 30
Figure 43: DX3010 DIP Switch Configuration ....................................................................................... 31
Figure 44: DX4010i to Control Panel Wiring ......................................................................................... 32
Figure 45: DX4010i to Control Panel Wiring (External Power Supply) ................................................. 32
Figure 46: DX4010i RPS Direct Connect Address Setting .................................................................... 33
Figure 47: DX4010i Direct Connection ................................................................................................. 33
Figure 48: DX4010 Direct Connection .................................................................................................. 34
Figure 49: P1 Jumper Pin Settings ....................................................................................................... 34
Figure 50: DX4010 P2 Jumper Pin Settings.......................................................................................... 35
Figure 51: RS-232 Device DIP Switch Setting ...................................................................................... 35
Figure 52: DB9 Connector Layout ........................................................................................................ 35
Bosch Security Systems, Inc. | 04/12 | F01U253045-02
EN | 4