Icom IC-7800 Instruction Manual page 207

D Command table (continued)
Cmd. Sub Cmd. Data
1A 050222 00, 01
050223 00 to 07 Send/read the peak color level for dis-
050224 00, 01
050225 see p. 14-11 Send/read waveform color for Audio
050226 00, 01
050227 see p. 14-11 Send/read waveform color for Audio
050228 00, 01
050229 01 to 15 Send/read the repeat interval to trans-
050230 00, 01
050231 00, 01
050232 00, 01
050233 00, 01
050234 00, 01
050235 00 to 03 Send/read QSO PLAY Skip time.
06 see p. 14-11 Send/read DATA mode with filter set
07 00
01
02
08 00
01
09 00
01
02
0A 00
01
02
1B 00 see p. 14-11 Send/read repeater tone frequency
01 see p. 14-11 Set/read TSQL tone frequency
1C 00 00
01
01 00
01
02
02 00 or 01 Send/read transmit frequency moni-
Description
Send/read the waterfall display on the
Spectrum scope. (00=OFF, 01=ON)
playing the waterfall.
00=Grid 1, 01=Grid 2, 02=Grid 3,
03=Grid 4, 04=Grid 5, 05=Grid 6,
06=Grid 7, 07=Grid 8
Send/read waveform type on the
Audio FFT scope.
(00=Fill, 01=Line)
FFT scope.
Send/read the waterfall display on the
Audio FFT scope. (00=OFF, 01=ON)
Oscilloscope scope.
Send/read the voice 1st menu.
(00=VOICE-Root, 01=VOICE-PLAY)
mit the recorded voice audio.
(01=1 sec. to 15=15 sec.)
Send/read the QSO recording device
setting.
( 00=CF memory card, 01=USB flash
drive)
Send/read the recording mode.
(00=TX&RX, 01=RX Only)
Send/read the squelch status for the
RX voice audio recording
(00=Always, 01=Squelch Auto)
Send/read the QSO audio record file
Split function setting.
(00=OFF, 01=ON)
Send/read the PTT Automatic Record-
ing function setting.
(00=OFF, 01=ON)
( 00=3 sec., 01=5 sec., 02=10 sec.,
03=30 sec.)
WIDE selection for SSB transmit
bandwidth
MID selection for SSB transmit band-
width
NAR selection for SSB transmit band-
width
SHARP selection for DSP filter type
SOFT selection for DSP filter type
3 kHz roofing filter selection
6 kHz roofing filter selection
15 kHz roofing filter selection
WIDE selection for manual notch
width
MID selection for manual notch width
NAR selection for manual notch width
Transceiver's condition (RX)
Transceiver's condition (TX)
Antenna tuner OFF (through)
Antenna tuner ON
Tuning
tor setting
(00=OFF, 01=ON)
Cmd. Sub Cmd. Data
1E 00
01 see p. 14-12 Read TX band edge frequencies
02
03 see p. 14-12 Send/read user-set TX band edge fre-
21 00 see p. 14-12 Send/read RIT frequency.
01 00, 01
02 00, 01
14-9
CONTROL COMMAND
Description
Read number of available TX fre-
quency band
Read number of user-set TX fre-
quency band
quencies
Send/read RIT setting.
(00=OFF, 01=ON)
Send/read ∂TX setting.
(00=OFF, 01=ON)
14