Table of Contents
Advertisement
ICP-CC488 | Installation Guide | 7.0
3. Enter [9 5 9 #].
Two beeps sound after a successful test of the
programming key. A long beep indicates that the
programming key data is corrupt and must be
erased to clear the corrupt data. Refer to Section
7.4.6 on page 38 for more information.
4. Enter [9 6 0 #] to exit from Installer's
Programming Mode.
Two beeps sound. The STAY and AWAY
indicators are extinguished on the remote
codepad and the system returns to the disarmed
state.
5. Remove the programming key from the control
panel.
Failure to exit from Installer's Programming
Mode before removing the programming key
can corrupt the data in the programming key.
7.4.2
Command 960 – Exit from Installer's
Programming Mode
This command exits from Installer's Programming
Mode. You can exit from Installer's Programming
Mode from any location.
To exit from Installer's Programming Mode:
Enter [9 6 0 #].
Two beeps sound and the system returns to the
disarmed state. When using the remote codepad, the
STAY and AWAY indicators are extinguished.
7.4.3
Command 961 – Reset the Control
Panel to Factory Default Settings
This command resets the control panel to factory
default values. Default values are listed throughout
this guide and in the programming sheets in
Section 25.0
Programming Sheets on page 101. You
can reset the control panel from any location.
To reset the control panel to factory defaults:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound and the STAY and AWAY
indicators flash on the remote codepad to
indicate that you entered Installer's
Programming Mode. The remote codepad
displays the data stored in Location 000.
2. Enter [9 6 1 #].
Two beeps sound and the system is reset to the
factory default values.
7.4.4
Command 962 – Copy the Control
Panel Memory to the Programming Key
This command copies the control panel memory to
the programming key. You can only use the CC891
Programming Key with the ICP-CC488 Control
Panel.
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
Programming
To copy the control panel memory to the
programming key:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound and the STAY and AWAY
indicators flash on the remote codepad to
indicate you entered Installer's Programming
Mode. The remote codepad displays the data
stored in Location 000.
2. Connect the programming key to the
PROGRAMMING KEY pins (next to the
Auxiliary Module socket) at the top of the
control panel found printed circuit board.
3. Enter [9 6 2 #].
Two beeps sound after the control panel
memory is successfully copied to the
programming key. A long beep indicates that the
programming key is corrupt and must be erased
to clear the corrupt data. Refer to Section 7.4.6
Command 964 – Erase the Programming Key on page
38 for more information.
4. Enter command [9 6 0 #] to exit from Installer's
Programming Mode.
The STAY and AWAY indicators are
extinguished on the remote codepad to indicate
the system is disarmed.
5. Remove the programming key from the control
panel.
Failure to exit from Installer's Programming
Mode before removing the programming key
can corrupt the programming key.
7.4.5
Command 963 – Copy the
Programming Key to the Control Panel
This command copies data from the programming
key to the control panel. You can use the CC891
Programming Key only with the ICP-CC488 Control
Panel.
To copy the programming key memory to the
control panel:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer's Programming Mode.
Two beeps sound and the STAY and AWAY
indicators flash on the remote codepad to
indicate you entered Installer's Programming
Mode. The remote codepad displays the data
stored in Location 000.
2. Connect the programming key to the
PROGRAMMING KEY pins (next to the
Auxiliary Module socket) at the top of the
control panel printed circuit board.
EN | 37
Advertisement
Table of Contents
