Bosch. material. Except as specified above or where authorised by the Bosch Security Systems Pty Ltd reserves the right to Copyright Act 1968 (Cth), no part of this publication make changes to features and specifications of its may be reproduced, transmitted, modified or stored, products at any time without prior notification.
CC488 | Quick Reference Guide | Contents EN | 3 2.1.8 Handshake Tone For Receiver 2 ....11 Contents 2.1.9 Transmission Format For Receiver 2 ...11 2.1.10 Subscriber ID Number For Receiver 2 ..11 Overview ............6 2.1.11 Dialling Format ..........11 Introduction............
Page 4
CC488 | Quick Reference Guide | Contents EN | 4 2.10.2 Open/Close Reporting Options....15 2.14.14 Speaker Beep Volume........19 2.10.3 Codepad Duress Report.........15 2.15 Options Programming........19 2.10.4 Codepad Panic Report........15 2.15.1 System Options 1 ..........19 2.10.5 Codepad Fire Report........15 2.15.2 System Options 2 ..........19 2.10.6 Codepad Medical Report ......15...
CC488 | Quick Reference Guide | 1.0 Overview EN | 6 To move to another programming location, enter the 1.0 Overview location number followed by the [#] key. The data in the new location is displayed using the codepad Introduction indicators.
CC488 | Quick Reference Guide | 1.0 Overview EN | 7 Table 2: Codepad Indicators Data Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 MAINS Value Indicator Indicator Indicator Indicator Indicator Indicator...
CC488 | Quick Reference Guide | 1.0 Overview EN | 8 Arming/Disarming the System Table 5: Arming/Disarming the System AWAY Mode STAY Mode 1 STAY Mode 2 Arming Press and hold the [#] key until two Press and hold the [*] key until two...
CC488 | Quick Reference Guide | 1.0 Overview EN | 9 1.12 Satellite Siren Service Mode 1.15 Change Domestic Telephone Numbers Enter the four character Installer Code, followed by [5] and the [#] key (for example, [1 2 3 4 5 #]).
CC488 | Quick Reference Guide | 1.0 Overview EN | 10 1.20 Fault Analysis 1.23 Codepad ID/Buzzer Tone 1. Press and hold the [5] key until two beeps are 1. Press and hold the [8] key until the desired heard.
CC488 | Quick Reference Guide | 2.0 Programming Parameters EN | 12 2.1.17 Telephone Line Fail Options User Code Programming Location 2.3.1 User Codes Default Location 185 to 264 Display FAULT Indicator when telephone line fails Location Default Sound alarm when system is armed...
CC488 | Quick Reference Guide | 2.0 Programming Parameters EN | 13 Day Alarm Zones 2.6.1 Zone Defaults (continued) Location Location 267 to 322 Default Zone #04 (Default = Handover) Zone 1 Zone Type Zone 2 Zone Pulse Count Zone 3...
CC488 | Quick Reference Guide | 2.0 Programming Parameters EN | 14 2.6.2 Zone Types 2.6.8 Keyswitch Zone Options Zone Type Description The keyswitch zone options replace Zone Options 1 only for the zones that were programmed to Instant operate as a keyswitch zone.
CC488 | Quick Reference Guide | 2.0 Programming Parameters EN | 20 2.20.3 RF Device Mapping for Devices 9 to 2.17 User Code Area Assignment Location 462 to 477 Location 536 to 543 Location Default Location Default User Code 1...
CC488 | Quick Reference Guide | 2.0 Programming Parameters EN | 21 2.21.3 System Date Location 905 to 910 Location Default Day of the month (tens digit) Day of the month (units digit) Month of the year (tens digit) Month of the year (units digit)
CC488 | Quick Reference Guide | 6.0 Wiring Diagrams EN | 25 Solution Ultima Series Figure 8: Solution Ultima Series Wiring Diagram 1 = 605 Plug 7 = Link between +12 V and Comm 2 = 1 (Green) - Internal phone line...
CC488 | Quick Reference Guide | 7.0 Component Overlay EN | 26 Component Overlay Figure 9: Solution Ultima Series Component Overlay 1 = OUT – Internal phone line 7 = Relay contact select OUT – Internal phone line 8 = Programming key or hand help programmer plugs IN –...