Table of Contents
Advertisement
ICP-CC488 | Installation Guide | 10.0
9.2
Setting Up and Programming
Domestic Reporting
Programming the control panel for domestic
reporting is extremely simple when using the
Installer's Programming Command 965. Refer to
Section 7.4.7 Command 965 – Set Up Domestic Dialing
Format on page 38 for more information.
To set up the control panel for domestic dialing:
1. Enter the Installer Code and press [AWAY] to
enter Installer's Programming Mode.
Two beeps sound and the STAY and AWAY
indicators flash.
2. Enter [9 6 5] and press [AWAY].
Two beeps sound. The control panel is now set
up for Domestic Dialing Format.
3. Enter [9 6 0] and press [AWAY] to exit from
Installer's Programming Mode.
Two beeps sound and the STAY and AWAY
indicators are extinguished. The system returns
to the disarmed state.
4. To program your telephone numbers, enter your
Master Code and press [2][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
If any telephone numbers are already
programmed, they are displayed one digit at a
time using the codepad indicators.
If no telephone numbers are programmed, two
additional beeps sound after you enter this mode.
These two beeps normally sound after the last
digit of the last phone number is displayed.
5. Enter the digits for telephone number 1, one
digit at a time.
As you enter each digit, the corresponding
codepad indicator lights.
6. After you enter all the digits of the first telephone
number, press [STAY][4] to insert a break
between the first telephone number and the sec
telephone number.
7. Repeat Step 6 for each additional phone number.
8. After the last digit of the last telephone number,
press [AWAY] to exit from this mode.
Table 38: Domestic Dialing Digits
Digit
Number to
Required
Program
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
Dialer Reporting Formats
Digit
Number to
Required
Program
8
8
9
9
*
[STAY]1
#
[STAY]2
4 sec pause
[STAY]3
break
[STAY]4
15
[STAY]5
Example
To program two separate telephone numbers (9672
1777 and 9672 1233), enter the following sequence:
[2 5 8 0 2][AWAY][9 6 7 2 1 7 7 7][STAY] [4 9 6 7 2
1 2 3 3][AWAY]
You can cancel domestic dialing at any time (for
example, you are moving and do not want the
system to continue calling your work place or mobile
phone).
To disable domestic dialing:
Enter your Master Code and press
[2][AWAY][STAY][4][AWAY].
10.0 Dialer Reporting Formats
10.1
Transmission Formats
The ICP-CC488 Control Panel provides a number of
transmission formats for its dialing and
communication features. Program the transmission
format for Receiver 1 in Location 033 and the
transmission format for Receiver 2 in Location 073
(refer to Section 11.4 Transmission Format for Receiver 1
and Receiver 2 on page 50). The control panel is set at
the factory to report in the Contact ID Format.
10.1.1
Contact ID Format
Contact ID Format can identify hundreds of
protection zones by their unique codes. This format
provides a single-digit Event Qualifier and a three-
digit Event Code that quickly identifies the reported
condition.
In general, Contact ID Format is very simple because
most of the Event Codes and Point ID Codes are
predefined. The base station software usually can
identify an alarmed zone by its Point ID Code and
usually pays little attention to the Event Code.
Refer to Section 10.1.3 Alarm Link Options on page 44
for more information about the ICP-CC488 Point ID
Codes.
EN | 43
Advertisement
Table of Contents
