Table of Contents
Advertisement
ICP-CC488 | Installation Guide | 11.0
Table 46: Telco Arm/Disarm Dialing Digits
Digit
Number to
Required
Program
terminator
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
To turn call forward (immediate) on, enter:
[* 2 1][forwarding telephone number][#]
Example
To immediately forward all incoming calls to the
telephone number 96721055 after arming the system
in AWAY Mode, program:
[11 2 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
To turn call forward (no answer) on, enter:
[* 6 1][forwarding telephone number][#]
Example
To forward all incoming calls, when there is no
answer, to the telephone number 96721055 after
arming the system in AWAY Mode, program:
[11 6 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
11.8
Telco Disarming Sequence
143 to 158
Location
Default
0
These locations allow you to deactivate call diversion
automatically on your telephone when you disarm
the system from AWAY Mode.
To turn call forward (immediate) off, enter:
[# 2 1 #]
Example
To disable call forward (immediate) after disarming
the system from AWAY Mode, program:
[12 2 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
To turn call forward (no answer) off, enter:
[# 6 1 #]
Example
To disable call forward (no answer) after disarming
the system from AWAY Mode, program:
[12 6 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
Dialer Information
Digit
Number to
Required
Program
8
8
9
9
0
10
*
11
#
12
4 sec pause
13
break
14
15
15
11.9
Call Back Telephone Number
159 to 174
Location
Default
0
This location stores the telephone number to call
when Upload/Download is requested or the user
holds down [6] to initiate a modem call from the
control panel to establish a communications link with
the remote computer. The computer must be running
the CC816 Alarm Link Software and must be set to
Waiting for an Incoming Call. The Call Back
Telephone Number is also required if Remote
Connection with Callback Verification is required
(refer to Section 8.1.3 on page 41).
Refer to Section 8.0 Alarm Link Software on page 40
for more information.
11.10 Ring Count
Location
175
8
Default
0
Panel does not answer
1 to 13
Number of rings until panel answers
14
Answering machine bypass 2
15
Answering machine bypass 1
This location sets the number of rings before the
control panel answers an incoming call. Set this
count to an acceptable level, noting that one ring is
"Ring, Ring – Ring, Ring" and that a Ring Count of
10 represents approximately 60 sec. This location has
an effect only if Remote Arming, remote
Upload/Download using Alarm Link, or both are
enabled. Programming this location to 0 prevents the
control panel from answering incoming calls
regardless of other programmed options.
Answering Machine Bypass
Answering Machine Bypass allows a connection with
the control panel for Remote Arming or
Upload/Download when an answering machine or
facsimile machine is on the same telephone line.
Answering Machine Bypass has two different
methods. Program a 14 to use the secondary method
only when there is a large amount of traffic on the
line (at a home office, for example). This method
reduces the chance of the control panel incorrectly
answering an incoming call.
Programming the Ring Count to 15 enables
Answering Machine Bypass in the primary mode.
When calling the control panel, allow the telephone
to ring no more than four times and then hang up. If
you call again within 45 sec, the control panel
answers the call on the first ring and the connection
is established. This prevents the answering machine
or facsimile machine from answering the call. To
enable Answering Machine Bypass only when the
system is armed, select Option 2 in Location 177
(refer to Section 12.1 Dialer Options 1 on page 52).
EN | 51
Advertisement
Table of Contents
