User Interface; 2.11.1 Commands; 2.11.2 Command Center Selections; Table 25: Command Center Programming Choices - Bosch D9412G Program Entry Manual

D9412G/D7412G | Program Entry Guide | 2.0 9000MAIN
•
Custom Functions can perform several tasks at
once. For example:
To toggle relays 7, 8, and 9 in one Custom
-
Function enter:
[A] [5] [4] [7] [E] [E] [8] [E] [E] [9] [E] [E] [C]
- To add a temporary passcode, enter:
[A] [5] [6] [3] [0] [E] [E] [9] [8] [7] [E] [E] [D]
[E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E]
[1] [E] [1] [E] [C]
This adds user 30, passcode 987 with
authority level 1 in all areas.
To delete the passcode, enter:
-
[A] [5] [3] [3] [0] [E] [E] [E] [C]
•
To program multiple area Arming or Disarming
functions, use keystroke sequences including
COMMAND 50 (Move to Area) and
COMMAND 1.
0101
Custom function cannot be used to change
0101
time (such as Daylight Savings Time). Use
0101
Skeds S## Function Codes 13 and 14 to
adjust for Daylight Savings Time (see S##
Custom Function prompt in Section 5.2
Skeds.
2.11

User Interface

Define which functions can be used by each of the
fourteen user authority levels. Each user can be
assigned the same or different authority level by
area. The user has rights in the area where the
command center is assigned based on the authority
level assigned to the user's passcode for that area.
When the passcode is entered at the command
center, the control panel checks the authority level.
The control panel executes the function only in
areas where the passcode has the authority to use the
function.

2.11.1 Commands

Similr to command initiation used in other Bosch
Security Systems products, the Commands method
provides continuity in the arming commands across
product lines and makes an easy transition for
dealers using other Bosch Security Systems products.
With commands, the end user presses
[COMMAND] and then the numeral of the
command to initiate. For example, [COMMAND][2]
arms the perimeter of the area. Some prompts can
only be accessed from a menu and is noted as such
by (Menu Function only). To access these functions,
press [MENU], enter the function number, and use
the [PREV] and [NEXT] keys to scroll through the
choices.
Bosch Security Systems | 10/03 | 47775E
The D9412G/D7412G Program Record Sheet lists the
commands available with the system. Command
numbers are shown in the column labeled
Command. If a particular function does not have a
command number, it can only be accessed through
the Function List.
If you plan to use only commands to operate the
system, along with arming and disarming by
entering a passcode, then you do not need to
program Custom Function or Function List.

2.11.2 Command Center Selections

Programming choices in this section determine if
command center functions are disabled (blank),
enabled (E), or restricted (P) panel-wide.
Press the [SPACE ] bar to scroll through the
selections. Press [ENTER] when the correct selection
appears in the display.
Table 25: Command Center Programming
Choices
Selection Description
Blank Disable the function panel-wide.
Accessing the function using a
command or the Function List
displays NO AUTHORITY.
E Enable the function panel-wide.
The function can be executed
without entering a passcode.
P Passcode required. When the
passcode is entered at the
command center, the control panel
checks the user's authority level.
See Section 2.11.3 Authority
Level Selections.
See Section 2.11.3 Authority Level
Selections for a detailed description of the
functions on the following pages. These
parameters only determine if the authority
level functions are passcode protected.
EN | 53