Table Of Contents; Icp-Cc488 | Installation Guide | Contents En - Bosch ICP-CC488 Installation Manual

ICP-CC488 | Installation Guide | Contents
Contents
1.0 Introduction......................................................8
1.1 ICP-CC488 Features .......................................8
1.2 Quick Start........................................................9
1.2.1 Set the Date and Time ....................................9
1.2.2 ICP-CC488 Zone Defaults .............................9
1.2.3 Zone Types.................................................... 10
2.0 Codepad Indicators ...................................... 10
2.1 ICP-CP508W Eight Zone LED Codepad . 10
2.2 ICP-CP508LW Eight Zone LCD Codepad11
2.3 ICP-CP500PW Master Partitioned LED
Codepad......................................................... 12
2.4 ICP-CP516 Sixteen Zone Codepads.......... 13
3.0 System Operations........................................ 14
3.1 Arming the System in AWAY Mode ........ 14
3.2 Disarming the System from AWAY Mode14
3.3 Arming the System in STAY Mode 1 ....... 14
3.4 Disarming the System from STAY Mode 115
3.5 Arming The System in STAY Mode 2 ...... 15
3.6 Disarming the System from STAY Mode 216
3.7 Codepad Duress Alarm ............................... 16
3.8 Codepad Panic Alarm.................................. 16
3.9 Codepad Fire Alarm .................................... 17
3.10 Codepad Medical Alarm ............................. 17
3.11 Isolating Zones .............................................. 17
3.11.1 Standard Isolating......................................... 17
3.11.2 Code to Isolate .............................................. 17
3.12 Fault Analysis Mode..................................... 18
3.13 Fault Descriptions ......................................... 18
.4.0 Remote Radio Transmitter Operations.......... 20
4.1 Indications from Remote Radio Transmitter
Operations ..................................................... 21
4.2 Remote Radio User Code Priority Levels. 21
4.3 Changing or Deleting Remote Radio User
Codes.............................................................. 21
5.0 System Functions .......................................... 22
5.1 Installer Code Functions.............................. 22
5.1.1 Add or Delete RF Wireless Devices .......... 22
5.1.2 Set the Number of Days until the First Test
Report............................................................. 23
5.1.3 Change Domestic Phone Numbers............ 23
5.1.4 Change Telco Arm/Disarm Sequence....... 24
5.1.5 Setting STAY Mode 2 Zones ...................... 25
5.1.6 Satellite Siren Service Mode ....................... 25
5.1.7 Turning Telephone Monitor Mode On and
Off................................................................... 25
5.1.8 Walk Test Mode ........................................... 26
5.1.9 Event Memory Recall Mode....................... 26
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
5.2 Master Code Functions ................................ 27
5.2.1 Arm or Disarm Both Areas at the Same
Time................................................................ 27
5.2.2 Changing and Deleting User Codes........... 27
5.2.3 Changing and Deleting Remote Radio User
Codes .............................................................. 28
5.2.4 Changing Domestic Phone Numbers......... 28
5.2.5 Change Telco Arm/Disarm Sequence ....... 29
5.2.6 Setting STAY Mode 2 Zones....................... 30
5.2.7 Turning Outputs On/Off ............................. 30
5.2.8 Setting the Date and Time ........................... 31
5.2.9 Walk Test Mode............................................ 31
5.2.10 Event Non-volatile Memory Recall Mode 31
5.3 User Code Functions .................................... 32
5.3.1 Arm or Disarm Both Areas at the Same
Time................................................................ 32
5.4 Hold-Down Functions .................................. 32
5.4.1 Arm the System in AWAY Mode .............. 32
5.4.2 Arm the System in STAY Mode 1 ............. 32
5.4.3 Arm the System in STAY Mode 2 ............. 32
5.4.4 Horn Speaker Test ........................................ 33
5.4.5 Bell Test.......................................................... 33
5.4.6 Strobe Test ..................................................... 33
5.4.7 Turning Day Alarm On and Off................. 33
5.4.8 Fault Analysis Mode ..................................... 33
5.4.9 Initiate a Modem Call .................................. 33
5.4.10 Reset Latching Outputs................................ 33
5.4.11 Change the Codepad Buzzer Tone ............ 33
5.4.12 Send Test Report........................................... 34
6.0 Remote Arming by Telephone ................... 34
7.0 Programming ................................................. 34
7.1 Programming with the Remote Codepad.. 34
7.2 Programming with the Programming Key 35
7.3 Programming Option Bits............................ 36
7.4 Installer's Programming Commands.......... 36
7.4.1 Command 959 - Test the Programming Key
......................................................................... 36
7.4.2 Command 960 - Exit from Installer's
Programming Mode...................................... 37
7.4.3 Command 961 - Reset the Control Panel to
Factory Default Settings ............................... 37
7.4.4 Command 962 - Copy the Control Panel
Memory to the Programming Key ............. 37
7.4.5 Command 963 - Copy the Programming
Key to the Control Panel ............................. 37
7.4.6 Command 964 - Erase the Programming
Key .................................................................. 38
7.4.7 Command 965 - Set Up Domestic Dialing
Format............................................................. 38
7.4.8 Command 966 - Enable/Disable the
Automatic Stepping of Locations................ 38
EN | 3