Stereo Bpm Delay - Korg microARRANGER Owner's Manual

a: BPM, b: L Delay Base Note, b: Times, c: C Delay Base
Note,
c: Times, d: R Delay Base Note, d: Times
The delay time is the length of the note obtained by multiply-
ing the "Base Note" parameter by the Times value, in relation
to the tempo specified by the "BPM" parameter (or the MIDI
Clock tempo if "BPM" is set to MIDI).

050: BPM Delay

(Stereo BPM Delay)

This stereo delay enables you to set the delay time to
match the song tempo.
Note: With extreme values, the sync may be lost.
Stereo In - Stereo Out
Left
Input Level D-mod
Input Level D-mod
Right
Tempo
BPM
Base Note x Times Adjust [%]
BPM
Base Note x Times Adjust [%]
BPM
Selects MIDI Clock and assigns tempo
a
R >
Display the error message if the right channel delay time exceeds the upper
limit
L Delay Base Note
Selects the type of notes to specify the left channel delay time 
Times
b
Sets the number of notes to specify the left channel delay time
Adjust [%]
Fine-adjust the left channel delay time
R Delay Base Note
Selects the type of notes to specify the right channel delay time 
Times
c
Sets the number of notes to specify the right channel delay time
Adjust [%]
Fine-adjust the right channel delay time
L Feedback
Sets the feedback amount for the left channel
Src
d
Selects the modulation source of feedback amount
Amt L
Sets the modulation amount of the left channel feedback
R Feedback
Sets the feedback amount for the right channel
e
Amt R
Sets the modulation amount of the right channel feedback
High Damp [%]
f
Sets the damping amount in the high range
Low Damp [%]
g
Sets the damping amount in the low range
Input Level Dmod [%]
Sets the modulation amount of the input level
h
Src
Selects the modulation source for the input level
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
i
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
Wet / Dry
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
Wet / Dry
MIDI, 40...240
Fx:049,
----, OVER!!
Fx:049,
x1...x16
Fx:049
–2.50...+2.50%
Fx:049,
x1...x16
Fx:049
–2.50...+2.50%
–100...+100
Off...Tempo
–100...+100
–100...+100
–100...+100
0...100%
Fx:043
0...100%
Fx:043
–100...+100
Fx:037,
Off...Tempo
Fx:037
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
051: Seq. Delay
(Sequential Delay)
This four‐tap delay enables you to select a tempo and
rhythm pattern to set up each tap.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
Tempo
BPM
Rythm Pattern
BPM
a
Selects MIDI Clock and assigns tempo
Rhythm Pattern
b
Selects a rhythm pattern
Tap1 Pan
Sets the panning of Tap1
Tap2 Pan
Sets the panning of Tap2
c
Tap3 Pan
Sets the panning of Tap3
Tap4 Pan
Sets the panning of Tap4

Feedback
Sets the feedback amount
Src
d
Selects the modulation source of feedback amount
Amt
Sets the modulation amount of the feedback
High Damp [%]
Sets the damping amount in the high range
e
Low Damp [%]
Sets the damping amount in the low range
Input Level Dmod [%]
Sets the modulation amount of the input level
f
Src
Selects the modulation source for the input level
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
g
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: BPM, b: Rhythm Pattern
With the tempo specified by the "BPM" parameter (or the
MIDI Clock tempo if "BPM" is set to MIDI), the length of one
beat equals the feedback delay time, and the interval
between taps becomes equal. Selecting a rhythm pattern will
automatically turn the tap outputs on and off. When "BPM" is
set to MIDI, the lower limit of the "BPM" is 44.
Effects
ER/Delay

Pan
Delay
Feedback
BPM
Fx:037,
Dry, 1:99...99:1, Wet
207
Wet / Dry
Wet / Dry
MIDI, 44...240
,
– – – ... 3
,
L, 1...99, R
L, 1...99, R
L, 1...99, R
L, 1...99, R
–100...+100
Off...Tempo
–100...+100
0...100%
Fx:043
0...100%
Fx:043
–100...+100
Off...Tempo
Fx:037
Off...Tempo
–100...+100