Korg microARRANGER Owner's Manual page 194

192 Effects
Pitch/Phase Mod.
028: AutoFadeMod.
(Stereo Auto Fade Modulation)
This stereo chorus/flanger effect enables you to control
the LFO speed and effect balance using auto fade, and
you can spread the sound by offsetting the phase of the
left and right LFOs from each other.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sine LFO Shape
AutoFade
AUTOFADE Src
Selects the modulation source that starts AutoFade
a Rate
Sets the rate of fade-in
Fade-In Dly (Fade-In Delay) [msec]
Sets the fade-in delay time
LFO Waveform
Selects LFO Waveform
b
LFO Shape
Determines how much the LFO waveform is changed
LFO Phase [degree]
c
Sets the LFO phase difference between the left and right
LFO Frequency Mod
d Switches between D-mod and AUTOFADE for the LFO frequency modula-
tion
LFO Frequency [Hz]
Sets the LFO speed
Src
e
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
L Delay Time [msec]
Sets the left channel delay time
f
R Delay Time [msec]
Sets the right channel delay time
Depth
g
Sets the depth of LFO modulation
Feedback
Sets the feedback amount
h
High Damp [%]
Sets the feedback damping amount in the high range
Wet/Dry Mod
i Switches between D-mod and AUTOFADE for the effect balance modulation
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175

Wet / Dry
Delay
Feedback
High Damp
Delay
Wet / Dry
LFO Phase
LFO Frequency
Wet / Dry
Off...Tempo
Fx:027,
00...2000msec
Triangle, Sine
–100...+100
–180...+180
D-mod, AUTOFADE
0.02...20.00Hz
Off...Tempo
–20.00...+20.00Hz
0.0...500.0msec
0.0...500.0msec
–100...+100
D-mod, AUTOFADE
–Wet...–1:99, Dry, 1:99...Wet
Fx:010, 020,
Off...Tempo
–100...+100
029: 2Voice Res
This effect resonates the input signal at a specified
pitch. You can set the pitch, output level, and pan set‐
tings for two resonators individually. You can control
the resonance intensity via an LFO.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Trim
+
Trim
Right
D
-mod
LFO
Manual
Control Mode
Switches the controls of resonance intensity
a
LFO/D-mod Invert
Reverses the Voice 1 and 2 control when LFO/D-mod is selected
1...100
Fx:027 LFO Frequency [Hz]
Sets the LFO speed
b
Fx:027 D-mod Src
Selects the modulation source that controls resonance intensity
Mod. Depth
Sets the amount of resonance intensity control via LFO/D-mod
c
Fx:020 Trim
Sets the input level at the resonator
Fx:010 Voice1: Pitch
Sets the voice1 Pitch for resonance
d
Fine [cent]
Fx:027
Fine-adjusts the voice 1 pitch for resonance
Voice1: Resonance
Sets the intensity of resonance when Control Mode = Manual
e
High Damp [%]
Sets the damping amount of resonant sound in the high range
Voice1: Level
Sets the Voice1 output level
f
Pan
Sets the Voice1 stereo image
Voice2: Pitch
Sets the Voice2 Pitch for resonance
g
Fine [cent]
0...200
Fine-adjusts the voice 2 pitch for resonance
Voice2: Resonance
Fx:020 Sets the intensity of resonance when Control Mode = Manual
h
High Damp [%]
0...100%
Fx:020 Sets the damping amount of resonant sound in the high range
Voice2: Level
Sets the Voice2 output level
i
Fx:027
Pan
Sets the Voice2 stereo image
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: Control Mode, e: Voice1: Resonance, h: Voice2:
Resonance
This parameter determines the resonance intensity.
When "Control Mode" = Manual, the "Resonance" parameter
sets the intensity of resonance. If the "Resonance" parameter
has a negative value, harmonics will be changed, and reso-
nance will occur at a pitch one octave lower.
High Damp
Resonator
Level Pan
Resonance
Resonator
Level Pan
High Damp
Invert: On/Off
Pitch, Fine [cent]
Control Mode
Manual, LFO, D-mod
Wet / Dry
Wet / Dry
,
Off, On

0.02...20.00Hz
Off...Tempo
–100...+100
0...100
C0...B8
–50...+50
–100...+100

0...100%

0...100
L6...R6
C0...B8
–50...+50
–100...+100

0...100%

0...100
L6...R6
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100