Korg microARRANGER Owner's Manual page 181

Low Cutoff [Hz]
Sets the center frequency for Low EQ (shelving type)
f
Gain [dB]
Table , "Sets the gain of Low EQ," on page 176
Mid1 Cutoff [Hz]
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
g
Sets the band width of Mid/High EQ 1
Gain [dB]
Sets the gain of Mid/High EQ 1
Mid2 Cutoff [Hz]
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
h
Sets the band width of Mid/High EQ 2
Gain [dB]
Sets the gain of Mid/High EQ 2
Direct Mix
Sets the amount of the dry sound mixed to the distortion
i
Speaker Simulation
Switches the speaker simulation on/off
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: Wah
The Wah parameter switches the wah effect on/off.
a: Sw
This parameter sets how the wah effect is switched on and off
via the modulation source.
When "Sw" = Moment, the wah effect is usually turned off. It
is turned on only when you press the pedal or operate the joy-
stick.
When a value for the modulation source is less than 64, "off" speed
is selected, and when the value is 64 or higher, "on" is selected.
When "Sw" = Toggle, the wah effect is switched between on
and off each time you press the pedal or operate the joystick.
The switch will be turned on/off each time the value of the modula-
tion source exceeds 64.
b: Wah Sweep Range, b: Wah Sweep Src
This parameter sets the sweep range of the wah center fre-
quency. A negative value will reverse the direction of sweep.
The wah center frequency can be controlled by the modula-
tion source specified in the "Wah Sweep Src" parameter.
d: Drive, e: Output Level
The degree of distortion is determined by the level of input
signal and the setting of "Drive". Raising the "Drive" setting
will cause the entire volume level to increase. Use the "Output
Level" parameter to adjust the volume level. The "Output
Level" parameter uses the signal level input to the 3-Band
EQ. If clipping occurs at the 3-Band EQ, adjust the "Output
Level" parameter.
d: Pre Low-cut
Cutting the signal in the low range before it is input to the Dis-
tortion will create a sharp distortion.
g: Q, h: Q
These parameters set the bandwidth of each equalizer. The
higher the value, the narrower the band becomes.
007: Param.4B Eq
20...1.0kHz
(Stereo Parametric 4-Band EQ)
–18...+18dB
This is a stereo 4‐band parametric equalizer. You can
select peaking type or shelving type for Band 1 and 4.
300...10.00kHz
The gain of Band 2 can be controlled by dynamic mod‐
0.5...10.0
ulation.

–18...+18dB
Stereo In - Stereo Out
Left
500...20.00kHz
0.5...10.0

–18...+18dB
Right
0...50
Off, On
Trim
a
Sets the input level
Dry, 1:99...99:1, Wet
Band1 Type
b
Selects the type of Band 1
Band4 Type
Off...Tempo
c
Selects the type of Band 4
Band2 Dynamic Gain Src
–100...+100
Selects the modulation source of the Band 2 gain
d
Amt [dB]
Sets the modulation amount of Band 2 gain
Band1 Cutoff [Hz]
Sets the center frequency of Band 1
Q
e
Sets the bandwidth of Band 1
Gain [dB]
Sets the gain of Band 1
Band2 Cutoff [Hz]
Sets the center frequency of Band 2
Q
f
Sets the bandwidth of Band 2
Gain [dB]
Sets the gain of Band 2
Band3 Cutoff [Hz]
Sets the center frequency of Band 3
Q
g
Sets the bandwidth of Band 3
Gain [dB]
Sets the gain of Band 3
Band4 Cutoff [Hz]
Sets the center frequency of Band 4
Q
h
Sets the bandwidth of Band 4
Gain [dB]
Sets the gain of Band 4
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
i
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
b: Band1 Type, c: Band4 Type
Selects a filter type for Band 1 and 4.

Band1 Band2 Band3 Band4
PEQ PEQ PEQ
Trim
LEQ
LEQ
Trim
PEQ PEQ PEQ
D
-mod
Parametric 4EQ - Band1, Band4 Type
3dB
+Gain
Band4 Type=Shelving High
Band4 Type=Peaking
0dB
Band1 Type=Shelving Low
Band1 Type=Peaking
–Gain
3dB
Band1 Cutoff
Effects 179
Filter/Dynamic
Wet / Dry
PEQ
HEQ
HEQ
PEQ
Wet / Dry
0...100
Peaking, Shelving-Low

Peaking, Shelving-High

Off...Tempo

–18...+18dB

20...1.00kHz
0.5...10.0
Fx:006
–18.0...+18.0dB
50...10.00kHz
0.5...10.0
Fx:006
–18.0...+18.0dB
,
300...10.00kHz
0.5...10.0
Fx:006
–18.0...+18.0dB
500...20.00kHz
0.5...10.0
Fx:006
–18.0...+18.0dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Band4 Cutoff