Korg microARRANGER Owner's Manual page 239

Files in Use Not Deleted (Press Exit)
This message may appear during an Erase operation.
Files used by other procedures have not been erased.
Files in use have not been overwritten
This message may appear during a Copy with Over‐
write operation. Files used by other procedures have
not been copied.
File Is Protected (Press Exit)
You were trying to overwrite a protected file.
File Not Found (Press Exit)
The file is not in the current medium. The card has
probably been replaced before finishing the card opera‐
tion. Insert the card again, and try again.
Format Completed (Press Exit)
Formatting has been successfully completed.
Format aborted (Press Exit)
Format operation aborted.
Format failed! (Press Exit)
An error occurred during Format. Format operation
aborted.
Illegal name (Press Exit)
The name is not allowed on microARRANGER.
Insert an SD card and press Enter
While saving the operating system "Save OS" on
page 141, or executing a Backup procedure (see
"Backup Data" on page 141), microARRANGER asks
for a card.
Invalid Copy Parameter (Press Exit)
The copy operation was not possible. Maybe you were
trying to copy a file over itself, or copying nested fold‐
ers.
Load Failed! (Press Exit)
The Load procedure has not been executed. Try again,
or try with different files.
Make New Dir Failed! (Press Exit)
While trying to create a new directory, an error
occurred.
Media Write-Protected (Press Exit)
The card is physically protected. Remove the protec‐
tion, and try again.
Memory full
This message appears in Backing Sequence mode,
when the memory for recording a Song is full.
No Card/Unformatted. (Sh+Enter to Format)
Either there is no card in the drive, or the card is unfor‐
matted. Insert a card, and try again, or press
SHIFT+ENTER to start formatting the card.
Not a Pa-series or Corrupted File
The file you are trying to load is not compatible with
microARRANGER or Pa‐series instruments.
Error messages & Troubleshooting
Not Enough Space on Media
There is no more space to load, save or copy data. The
card operation will be aborted. Replace the card, and
use an empty card to save your data. Should this mes‐
sage appear during loading, the SSD (Solid State Disk)‐
based internal memory is full.
Nothing to Rename (Press Exit)
There are no items to rename.
Overwrite Existing File? (Yes/No)
You are writing data on an existing ".SET" folder, or on
a file of type ".MID" or ".JBX".
Overwrite on Backup? (Enter/Exit)
Press ENTER/YES to overwrite files carrying the same
name on the target device, or EXIT/NO to avoid over‐
writing any file.
Overwrite on Copy? (Enter/Exit)
Press ENTER/YES to overwrite files carrying the same
name on the target device (Press Exit)/NO to avoid
overwriting any file. File that are not yet on card are
always copied.
Overwrite Protected Files? (Enter/Exit)
Protected files cannot usually be overwritten. By press‐
ing ENTER, you can overwrite them during the current
operation.
Rename: Invalid Name (Press Exit)
You can't use the name you entered. Please retry and
select a different name.
Rename: New Name Must Be a \".SET\
You can't modify a ".SET" folder extension.
Rename Failed! (Press Exit)
An error occurred during Rename. Rename operation
aborted.
Save Failed! (Press Exit)
An error occurred during Save. Save operation aborted.
Some Files Missing (Press Exit)
This message may appear at the end of a Restore opera‐
tion. Some User file may be missing. This is not a prob‐
lem for the Factory Data integrity.
Unit Not Found (Press Exit)
You were trying to access a storage device not available
on your instrument.
Unformatted medium
You have selected a medium (card) that is not yet for‐
matted, or is in a format that microARRANGER can't
recognize. Format the medium using the Format proce‐
dure (see "Page 5 ‐ Format" on page 140).
Wait
microARRANGER is busy with a card operation.
237
Error messages