019: Ensemble
This Ensemble effect has three chorus blocks that use
LFO to create subtle shimmering, and gives three
dimensional depth and spread to the sound, because
the signal is output from the left, right, and center.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Right
Shimmer
LFO
Speed
Sets the LFO speed
Src
a
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
Depth
Sets the depth of LFO modulation
Src
b
Selects the modulation source of the LFO modulation depth
Amt
Sets the modulation amount of the LFO modulation depth
Shimmer
c
Sets the amount of shimmering of the LFO waveform
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
d
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
c: Shimmer
This parameter sets the amount of shimmering of the LFO
waveform. Increasing this value adds more shimmering, mak-
ing the chorus effect more complex and richer.
Level
Wet / Dry
Ensemble
Wet / Dry
1...100
Off...Tempo
–100...+100
0...100
Off...Tempo
–100...+100
0...100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Ensemble LFO
Shimmer
Time
020: Flanger
(Stereo Flanger)
This effect gives a significant swell and movement of
pitch to the sound. It is more effective when applied to
a sound with a lot of harmonics. This is a stereo flanger.
You can add spread to the sound by offsetting the
phase of the left and right LFOs from each other.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sine
Delay Time [msec]
a
Sets the delay time from the original sound
LFO Waveform
Selects LFO Waveform
b
LFO Shape
Determines how much the LFO waveform is changed
LFO Phase [degree]
c
Sets the LFO phase difference between the left and right
LFO Frequency [Hz]
Sets the LFO speed
Src
d
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
e
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Depth
f
Sets the depth of LFO modulation
Feedback
Sets the feedback amount
g
High Damp [%]
Sets the feedback damping amount in the high range
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
h
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
b: LFO Shape
Changing the LFO waveform shape controls the peak sweep
of flanging effects.
LFO Shape = 0...+100
g: Feedback, h: Wet/Dry
The peak shape of the positive and negative "Feedback"
value is different. The harmonics will be emphasized when
the effect sound is mixed with the dry sound if you set a posi-
Effects
Pitch/Phase Mod.
Flanger
Feedback
High Damp
Flanger
LFO Phase
LFO Shape
Fx:009,
–20.00...+20.00Hz
Fx:009,
–Wet...–1:99, Dry, 1:99...Wet
Fx:010,
LFO Shape
LFO Shape = 0...–100
LFO Waveform=Sine
187
Wet / Dry
Wet / Dry
0.0...50.0msec
Triangle, Sine
–100...+100
–180...+180
Fx:010
0.02...20.00Hz
Off...Tempo
Off, On
MIDI, 40...240
Fx:009
Fx:009
x1...x16
Fx:009
0...100
–100...+100
0...100%
Off...Tempo
–100...+100