Korg microARRANGER Owner's Manual page 182

180 Effects
Filter/Dynamic
d: Band2 Dynamic Gain Src, d: Amt [dB], f: Gain [dB]
You can control the gain of Band 2 using the modulation
source.
D
+15dB
+6dB
0dB
Band2 Cutoff
Band2 Gain[dB]= +6.0
Band2 Dynamic Gain Amt[dB]= +9.0

008: Graph.7B Eq
(Stereo Graphic 7 Band EQ)
This is a stereo 7‐band graphic equalizer. The bar graph
of the gain setting for each band gives you a clear,
visual idea of frequency responses. You can select a
center frequency setting for each band from twelve
types, according to the sound.
Stereo In - Stereo Out
Left
Trim
Band1 Band2 Band3 Band4
Trim
Band1 Band2 Band3 Band4 Band5 Band6 Band7
Right
Type 1:Wide 1, 2:Wide 2, 3:Wide 3, 4:Half Wide 1, 5:Half Wide 2, 6:Half
a Wide 3, 7:Low, 8:Wide Low, 9:Mid, 10:Wide Mid, 11:High, 12:Wide High
Selects a combination of center frequencies for each band
Trim
b
Sets the input level
Band1 [dB]
c
Sets the gain of Band 1
Band2 [dB]
d
Sets the gain of Band 2
Band3 [dB]
e
Sets the gain of Band 3
Band4 [dB]
f
Sets the gain of Band 4
Band5 [dB]
g
Sets the gain of Band 5
Band6 [dB]
h
Sets the gain of Band 6
Band7 [dB]
i
Sets the gain of Band 7
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
a: Type
This parameter selects a combination of center frequencies
for each band. Each center frequency is shown on the right
edge of the LCD.
Parametric 4EQ - Band2 Dynamic Gain Control
-mod
Band2 Cutoff
+6dB
0dB
–9dB
D
-mod
Band2 Gain[dB]= +6.0
Band2 Dynamic Gain Amt[dB]= –15.0
Wet / Dry
Band5 Band6 Band7
Wet / Dry
–18.0...+18.0dB
–18.0...+18.0dB
–18.0...+18.0dB
–18.0...+18.0dB
–18.0...+18.0dB
–18.0...+18.0dB
–18.0...+18.0dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
You can configure a 21-Band Graphic EQ ranging from 80Hz
to 18kHz if you route three Graphic 7Band EQ effects in
series, with a setting of 7:Low, 9:Mid, and 11:High for each
EQ.
009: Wah/AutoWah
(Stereo Wah/Auto Wah)
This stereo wah effect allows you to create sounds from
vintage wah pedal simulation to auto‐wah simulation,
and much broader range settings.
Stereo In - Stereo Out
Left
Envelope Sens
+
Right
Frequency Bottom
Sets the lower limit of the wah center frequency
a
Frequency Top
Sets the upper limit of the wah center frequency
Sweep Mode
Selects the control from auto-wah, modulation source, and LFO
b Src
Selects the modulation source for the wah when Sweep Mode=D-mod
Response
Sets the response speed when Sweep Mode = Auto or D-mod
Envelope Sens (Envelope Sensitivity)

Sets the sensitivity of auto-wah
c
0...100
Envelope Shape
Sets the sweep curve of auto-wah
LFO Frequency [Hz]
Sets the LFO speed
Src
d
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
e
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Resonance
Sets the resonance amount
f
Low Pass Filter
Switches the Wah Low Pass Filter on and off
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
g
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175

Wah
Sweep Mode
Envelope Shape
Auto
Response
D-mod
D
-mod
LFO
LFO
Wah
Auto, D-mod, LFO
–20.00...+20.00Hz
, ,
Dry, 1:99...99:1, Wet
Wet / Dry
Wet / Dry
0...100

0...100

,
Off...Tempo
0...100
0...100

–100...+100

0.02...20.00Hz
,
Off...Tempo
Off, On
,
MIDI, 40...240

, , , , ,

x1...x16

0...100
Off, On
Off...Tempo
–100...+100