1. Manuals
  2. Brands
  3. Beisler Manuals
  4. Sewing Machine
  5. 2110/5
  6. Working instructions

Beisler 2110-5 Working Instructions

Hide thumbs Also See for 2110-5:
Table of Contents

Advertisement

Quick Links

Beisler Automated Sewing Equipment
Short Seam Automat 2110-5 / 2111-5 Working Instructions
Working Instructions
Short Seam Automat 2110-5 / 2111-5
DOC 000060
- A 1 -

Advertisement

Table of Contents
loading

Related Manuals for Beisler 2110-5

Summary of Contents for Beisler 2110-5

  • Page 1 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Working Instructions Short Seam Automat 2110-5 / 2111-5 DOC 000060 - A 1 -...
  • Page 2 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Contents of the working instructions The working instructions are divided into four sections: General notes: page A 1 - A 10 Safety instructions for the operating and service personnel and for the opera- tor of the machine.
  • Page 3 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Section A General notes - A 3 -...

  • Page 4: Table Of Contents

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Section A General notes Contents A.1 Safety instructions ......................5 A.1.1 Symbols used in the working instructions ..............8 A.1.2 Symbols used on the machine ..................8 A.1.3 General safety instructions ....................

  • Page 5: Safety Instructions

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Safety instructions Important information for the operator! This machine has been manufactured in keeping with the latest technological develop- ments and is operationally safe. However, it may present potential hazards, particu- larly if it is operated by inadequately trained personnel or if it is not used correctly: •...
  • Page 6 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Safety instructions Exclusion of liability Beisler GmbH warrants the faultlessness of the product as set forth by their advertisement, product information and these working instructions. Other product characteristics are not warranted. Beisler GmbH is not responsible for the profitability or for the correct function of the short seam automat 2110-5 / 2111-5 if it is used for other purposes than those defined in section „Correct use“.
  • Page 7 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Safety instructions Important information for the operating personnel! Please note that any work to the SHORT SEAM AUTOMAT 2110-5 / 2111-5 must be carried out only by trained operating personnel: •...

  • Page 8: Symbols Used In The Working Instructions

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Safety instructions A.1.1 Symbols used in the working instructions A.1.2 Symbols used on the machine WARNING! WARNING: DANGER! is used if non-observance may cause serious or even lethal Caution! Observe working instructions.

  • Page 9: General Safety Instructions

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Safety instructions A.1.3 General safety instructions Correct use Safety devices • The SHORT SEAM AUTOMAT 2110-5 / 2111-5 is a The SHORT SEAM AUTOMAT 2110-5 / 2111-5 is equip- sewing machine.

  • Page 10: Notices

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Notices - A 10 -...

  • Page 11: Operating Instructions

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Section B Operating Instructions - B 11 -...
  • Page 12 Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Section B Operating instructions Contents B.1 Description of the machine ....................12 B.1.1 Functional units ......................13 B.2 Functions of the machine ....................14 B.2.1 Functional sequence ....................14 B.2.2 Line-up and alignment ....................

  • Page 13: Description Of The Machine

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Description of the machine Fig. 1 B.1.1 Functional units All functional units of the SHORT SEAM AUTOMAT Control unit 2110-5 / 2111-5 are mounted to the height-adjustable table Operating panel frame and freely accessible.

  • Page 14: Functions Of The Machine

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine B.2.1 Functional sequence Fig. 2/3 Fig. 2 The short seam automat 2110-5 / 2111-5 allows the au- tomatic crimping over of pocket edges and the tucking of pocket edges to pocket bags.
  • Page 15 Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine B.2.2 Line-up and alignment Fig. 4 Fig. 4 Crimping over and picking up pocket edge, The folder moves to the right to the pick-up plate .
  • Page 16 Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine B.2.2 Line-up and alignment Fig. 5 Fig. 5 Manual labeling, Single labels are positioned manually with the pocket bag . The exact line-up position of the labels is marked with the reticle of the guide laser Automatic label feed system, The short seam automat can be equipped with an au-...

  • Page 17: Transport And Sewing

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine Fig. 6 B.2.3 Transport and sewing Folder Sewing head The folder moves to the left with the pocket edge, The sewing head performs only the functions sewing is lowered and puts the pocket edge onto the pocket stitch and thread cutting.

  • Page 18: Switches

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine B.2.4 Switches Fig. 7 The short seam automat is equipped with three different Supply switches: types of switches: Main switch • Emergency switch for stopping a sewing program, The main switch is used to turn the power supply •...

  • Page 19: Operating Panel

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Functions of the machine B.2.5 Operating panel Fig. 8 Fig. 8 Display During the operation of the machine, the display shows the values of the selected sewing program. If menus were requested, the menu symbol or the cor- responding parameters of the function are displayed.

  • Page 20: Operation

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.1 Safety instructions for operation Machine operation: Handling the guide laser: WARNING - Machine operation intervention! CAUTION - Damage of the retina! The machine is driven by electric motors and by com- If the eye is directed toward the laser beam for some pressed air.

  • Page 21: Preparing The Machine

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.2 Preparing the machine Fig. 9 Prior to the production start, check the supply connections, Fig. 9 connect the machine to the compressed air and power supply systems and prepare the sewing head. 1.

  • Page 22: Selecting The Sewing Program

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.3 Selecting the sewing program Fig. 10/11 After the machine has been switched on and the control Fig. 10 program has been booted, the display on the ope- rating panel shows the most recently selected sewing program.

  • Page 23: Activating Additional Seam Numbers

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.4 Activating additional seam numbers B.3.7 Setting the thread clamp manually 1. Select seam number of desired seam. Before the first start of a sewing program, the top thread clamp must be activated to protect the top thread from Move cursor to seam number: being pulled out of the needle when the machine starts.

  • Page 24: Aligning Sewing Pieces

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation Fig. 12 B.3.9 Aligning sewing pieces Fig. 12 The line-up positions of pocket edge, pocket bag and label must be aligned to one another. 1. Mark the exact position of the pocket at the line-up station with tape or pen.

  • Page 25: Quick Stitch Width Setting

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.10 Quick stitch width setting Fig. 13 Fig. 13 The quick stitch width adjustment makes the selection of 4 preadjusted different stitch widths possible. NOTE - Stitch width! The stitch width depends on the thickness of the fabric.

  • Page 26: Starting Machine Cycle

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.11 Starting machine cycle A machine cycle can be started in four different sequences 8. Depress, then release footswitch for machine cycle: (mode 00, mode 01, mode 02, mode 03). The factory de- •...

  • Page 27: Resetting Line-Up Process

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Operation B.3.14 Stopping a sewing program Controlling machine cycle in mode 03: 1. Press key STOP. After each working step the following machine cycle can When the key STOP is pressed, the program stops. All be continued automatically.

  • Page 28: Service Instructions

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Section C Service Instructions - C 27 -...
  • Page 29 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Section C Service Instructions Contents C.1 Delivery of the machine ....................29 C.1.1 Packaging ........................29 C.1.2 Scope of delivery ......................29 C.2 Storage and location requirements ................. 30 C.2.1 Floor quality .........................

  • Page 30: Delivery Of The Machine

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Delivery of the machine C.1.1 Packaging C.1.2 Scope of delivery The machine is delivered in a solid packaging box on a The machine is delivered in an operative condition. The pallet.

  • Page 31: Storage And Location Requirements

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Storage and location requirements C.2.1 Floor quality C.2.4 Supply connections The floor of the room where the machine is to be instal- The machine requires on-site power and compressed air led must have a sufficient surface strength.

  • Page 32: Start-Up

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Start-up C.3.1 Machine table alignment Fig. 1/2 Fig. 1 After the machine has been installed at the desired loca- tion, the machine table must be aligned: • Set machine table to required height. •...

  • Page 33: Compressed Air Connections

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Start-up C.3.2 Compressed air connections Fig. 3 Fig. 3 Fig. 3: The compressed air connection is preinstalled on the machine. It comprises the following components: • Pressure reducer with manometer and water separator...

  • Page 34: Connecting The Machine To The Power Supply

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Start-up C.3.4 Safety check C.3.3 Connecting the machine to the power supply Before the machine is released for operation, all safety de- The power cable and the power plug are preinstalled on vices must be checked for their correct operation.

  • Page 35: Operation And Shut-Down

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Operation and shut-down C.4.1 Working with the machine C.4.2 Machine shut-down Factory settings: When the machine is to be shut down, it must be discon- The machine has a factory-programmed standard program nected from all supply sources.

  • Page 36: Maintenance

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance WARNING - Electric shock! C.5.2 Cleaning Contact with current-carrying components may cause The machine must be cleaned after large production se- a lethal electric shock ries, or at least once a day, whichever occurs first. If the machine is put in motion accidentally, persons in its direct vicinity may be caught by moving parts Cleaning the machine surfaces:...
  • Page 37 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.3 Service Fig. 4 Fig. 4 The following service works must be carried out in weekly intervals. Oiling the clamp rail: 1. Disconnect machine from power supply. 2.

  • Page 38: Service

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.4 Repairs Fig. 5 Fig. 5 Any repairs to the machine must only be carried out by: • authorized Technical Service, • personnel that has been instructed about the setting up and maintenance of the machine on the occasion of a training by the supplier or manufacturer.

  • Page 39: Clamp Transport Belt Replacement

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.4 Repairs Fig. 6/7 Fig. 7 Clamp transport belt replacement: 1. Disconnect machine from power supply system. 2. Slide clamp to left until it reaches stop position. 3.

  • Page 40: Clamp Rail Replacement

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.4 Repairs Fig. 8 Fig. 8 Clamp rail replacement: The clamp rail must be replaced if the protective lining at the bottom side of the rail is worn. Clamp rail removal: 1.

  • Page 41: Machine Set-Up

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.5 Machine set-up Fig. 9 Fig. 9 NOTE - Activating inputs /outputs! To allow for testing machine movements or interval opera- tion, the individual stages of movement can be activated with the inputs/outputs of the machine control unit (see pro- gramming instructions, section D.3.3, service menu level 1).

  • Page 42: Clamp Rail Clamping Pressure Adjustment

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.5 Machine set-up Fig. 10/11 Fig. 10 After any works to the main clamp, the clamping pressure and the alignment of the clamp rail to the needle must be checked.

  • Page 43: Adjustment Of Clamp Slide Disengagement Position

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.5 Machine set-up Fig. 12/13 Fig. 12 Adjustment of clamp slide disengagement positi- The disengagement position of the clamp slide is adjusted for the front and rear stop point at the pedestal. Fig.

  • Page 44: Folder To Clamp Rail Alignment

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.5 Machine set-up Fig. 14 Fig. 14 Folder to clamp rail alignment: The lowered folder must be absolutely parallel to and in slight contact with the clamp rail along its entire length. Folder position adjustment: 1.

  • Page 45: Folder To Pick-Up Plate Alignment

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.5 Machine set-up Fig. 15 Folder to pick-up plate alignment: Fig. 15 To ensure that the folder can pick up the pocket edge even- ly, the folder must lie upon the pick-up plate along its entire length.

  • Page 46: Folder Bar To Folder Clamp Alignment

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.5 Machine set-up Fig. 16/17 Folder bar to folder clamp alignment: Fig. 16 To ensure that the folder can crimp over the pocket edge evenly, the folder clamp must pe positioned centrically above the folder bar Folder bar adjustment:...

  • Page 47: Photocell Light Sensitivity Setting

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.5 Machine set-up Fig. 18 Photocell light sensitivity setting: Fig. 18 The photocell at the sewing head controls the begin- ning and the end of the sewing process. The sensitivity of the photocell must be set in accordance with the sewing material used.

  • Page 48: Installation Stepper Motor

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.5 Machine set-up Fig. 19 Installation stepper motor: Fig. 19 The PCB for controlling the stepper motor is installed in the control box. NOTE - Machine cycle! To prevent moving machine parts from colliding with each other or with other components when the machine is swit- ched on again, move the machine manually into its start...

  • Page 49: Setting The Thread Cutter

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance Fig. 20 C.5.5 Machine set-up Fig. 20 Setting the thread cutter: The three-digit value input (GP Par. 35) determines when the thread cutter is activated. The setting of the thread cutter must be checked during machine operation and corrected as required.

  • Page 50: Checking The Rest Thread Monitor

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Maintenance C.5.5 Machine set-up Fig. 21 Fig. 21 Checking the rest thread monitor: The rest thread monitor is checked using a photocell. If the messages on the display do not match the filling state of the spool, the photocell sensitivity must be checked.

  • Page 51: Adjust Stitch Width

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Maintenance C.5.5 Machine set-up Fig. 22 Adjust stitch width: Fig. 22 The quick stitch width adjustment makes the presetting of 4 different stitch widths possible. 1. Fig. 22: Turn the handwheel to the required ran- 2.

  • Page 52: Troubleshooting

    Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Troubleshooting Error 01: Current sewing program empty; possibly Insert program values manually, copy from „Sewing program empty“ distances and routes have not been input other program or retrieve from ROM or the entire program was erased (parameter INIT) Error 02 :...
  • Page 53 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Troubleshooting Error 13: Excessive difference between nominal Remove blocked component; check clamp „Clamp position error“ position (step motor default) and actual slide for easy movement; check motor position (pulse from incrimental sensor) of pinion (may be loose on shaft);...
  • Page 54 Short Seam Automat 2110-5 / 2111-5 Working Instructions Beisler Automated Sewing Equipment Troubleshooting Error 32: During thread cutting, sewing motor did not Input slower cutting speed and earlier „Thread position does not reach cutting position cutting position; replace sewing motor or come“...

  • Page 55: Specifications

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Working Instructions Specifications Compressed air Power supply Operating pressure 6 bar Supply voltage 230 V ±10 %, 50/60 Hz Connection to supply (1, N, PE) AC Quality oil-free Air consumption 12 NL Power consumption 1.3 kW...
  • Page 56 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Section D Programming Instructions - D 56 -...
  • Page 57 Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Section D Programming Instructions Contents D.1 Operating panel ......................... 59 D.1.1 Display and key functions .................... 59 D.2 Fundamentals of programming ..................60 D.2.1 Program control layout ....................60 D.2.2 Program level overview ....................
  • Page 58 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Section D Programming Instructions Contents D.3.9 Level 5 special parameters / Functions ............... 81 Switching the top thread monitor on or off .............. 81 Switching the rest thread monitor or bottom thread monitor on or off ....81 Switching clamp position after end of seam on or off ..........

  • Page 59: Operating Panel

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Operating panel D.1.1 Display and key functions Fig. 1 Fig. 1 Display During machine operation, the display shows the values of the selected sewing program. If menus are activated, the menu symbols or the correspon- ding parameters of the function are displayed.

  • Page 60: Fundamentals Of Programming

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Fundamentals of programming D.2.1 Program control layout The program control is controlled using four different kinds Sewing program of menus: A sewing program controls the entire machine operation 1.
  • Page 61 Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Fundamentals of programming D.2.1 Program control layout Access to menus Factory setting The following menus are freely accessible: The machine comes with a factory-installed standard pro- • Service menu, gram (M 01) with six seams (01, 02, 03, 04, 05, 06).

  • Page 62: Program Level Overview

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Fundamentals of programming D.2.2 Program level overview Fig. 2 jkrmno*q Start level abcdefgh Service menu System menu (Direct access (Submenus) F1 - F8) ABCD Level 1 abcdefgh Global parameter menu Special parameter menu (Parameter list) Operating levels with functions/parameter lists...

  • Page 63: Programming

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.1 System menu The system menu is divided into several submenus. The NOTE - Submenu levels! submenus themselves are divided into access-protected and open submenus. Access is protected by the service All input for the system menus must be started from the code.

  • Page 64: Setting The Seam Sequence

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.1 System menu D.3.1 System menu Eprom seam parameters Copying seam numbers This function allows to copy the factory-programmed fi- Use this function to copy the properties of a factory-pro- xed seams from the Eprom back to the sewing program.

  • Page 65: Entering Seam Names

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.1 System menu Copying sewing programs to the memory stick • Press key (erase seam). Programmed sewing programs can be copied to the memory stick (back-up copies). •...

  • Page 66: Copying Variables To The Memory Stick

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.1 System menu D.3.1 System menu Running clamp motor in permanent test Copying variables to the memory stick The clamp motor can be run permanently to check for All variables (global parameters/special parameters) can be constant machine movement.

  • Page 67: Service Menu Start Level

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.2 Service menu start level The service functions of the service menu are requested Enter a completely new numeric value: by direct access from the start level or from level 1. Ser- •...

  • Page 68: Photocell Correction For End Of Seam, Seam Length And Fixed Seam End Point

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.2 Service menu start level Photocell correction for end of seam, seam length Seam 5: The beginning and the end of the seam are de- and fixed seam end point termined by the scan points of the photocell, the automatic The settings made in this menu refer to the selected needle label feed is an integral part of the machine operation.

  • Page 69: Filling Spool

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.2 Service menu start level Filling spool Resetting the insertion process Insert thread and fill spool: This function depends on the mode of machine operati- on. It refers only to machine movements that can be per- formed before the automatic operation.

  • Page 70: Manual Winding

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.3 Service menu level 1 Functions on level 1: Confirm input and exit menu: The function keys on the start level are assigned to the symbols above them as shown on the display. •...
  • Page 71 Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.3 Service menu level 1 Manual winding Select output: This function is used to wind thread from the thread spool to the top thread spool. To start the function: •...
  • Page 72 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.3 Service menu level 1 Outputs Valve Output Cylinder Signal Valve number number output type Open / close clamp X07 Pin02 5/2 way Move clamp in / out sideways X07 Pin03 5/2 way Swing folder left / right...

  • Page 73: Global Parameters

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.4 Global parameters Global parameters are values that control the basic func- Browse through list: tions of the machine. If global parameters are changed, • Press key. this change affects all stored sewing programs.
  • Page 74 Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.4 Global parameters Programmable global parameters (F2) TILL CLAMP SIDEWAYS FWD: Scan and part pickup after clamp movement forward / time interval TILL CLAMP DOWN ..: Lower clamp after clamp movement forward for part pickup / time interval TILL VACUUM OFF ..: Switch vacuum off after clamp down / time interval THRD LENGTH,BOBBIN FULL...
  • Page 75 Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.4 Global parameters Programmable global parameters (F2) TILL SCISSORS CLOSED: Time until scissors pinch the trousers component DURATION SCISSORS CUTS: Time during which the scissors are closed TILL FABRIC CLAMP OPEN: Time during which the fabric clamp is closed TILL SWING RETAINER DWN:...

  • Page 76: List Of Special Parameters

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.5 List of special parameters Special parameters are values that refer to only one Request / exit special parameter menu specific sewing program. Changes of these values affect Select sewing program and change from start level to level 1: only the currently selected sewing program for which the setting is made.
  • Page 77 Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.5 List of special parameters Programmable special parameters in lists (F3) TACKING LENGTH SEAM END: Final bar tack length only for lock stitch STITCH LENGTH SEAM BEG: Stitch length at beginning of seam (input 5.0 mm max.) DISTANCE OF THIS ST.LEN: Distance of stitch length at beginning of seam...

  • Page 78: Level 2 Special Parameters / Functions

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.6 Level 2 special parameters / Functions Fig. 3 Fig. 3 Functions of level 2 submenus: The following section describes the special parameters that can be enabled or disabled as functions. Back to start level Enable / disable functions Enabling / disabling functions...

  • Page 79: Level 3 Special Parameters / Functions

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.7 Level 3 special parameters / Functions Level 3 submenus: Switching folder on or off The folder puts the pocket edge onto the pocket bag. If this function is disabled, the pocket edge must be put onto the pocket bag manually.

  • Page 80: Level 4 Special Parameters / Functions

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.8 Level 4 special parameters / Functions Level 4 submenus: Switching label feed on or off Folded labels can only be sewed up using the automatic label feed function. Plain labels can be put onto the pocket edge manually when the automatic label feed is switched off.

  • Page 81: Level 5 Special Parameters / Functions

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.9 Level 5 special parameters / Functions Level 5 submenus: NOTE - Operation without thread monitor! During normal production, the rest thread monitor or the top thread monitor should always be switched on as other- wise the sewing programm will not be stopped if the thread breaks.

  • Page 82: Level 2 Special Parameters / Lists

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Programming D.3.10 Level 2 special parameters / Lists Parameter setting for level 2 submenus Settable values The following section describes the special parameters that Start mode are set in lists. When a submenu is requested, only tho- The selected start mode determines how the machine se positions of the parameter list are displayed that refer operation is started and executed.

  • Page 83: Setting Stitch Lengths And Bar Tacks

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Programming D.3.10 Level 2 special parameters / Lists Setting stitch lengths and bar tacks Parameters for clamp transport All settings for the configuration of the seam can be chan- This list is used to make all settings for the clamp move- ged using this list.

  • Page 84: Factory Settings

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Factory settings D.4.1 Factory settings for global parameters M01 Global parameters 2110-5 Pos. global parameters 2110-5 Value Unit Till CLAMP SIDEWAYS FWD TILL CLAMP DOWN TILL VACUUM OFF THREAD LENGTH spool full TILL CLAMP INSERTING SEWING END ->CL.SIDEW.

  • Page 85: M01 Global Parameters 2111-5

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Factory settings D.4.1 Factory settings for global parameters M01 Global parameters 2111-5 Pos. global parameters 2111-5 Value Unit Till CLAMP SIDEWAYS FWD TILL CLAMP DOWN TILL VACUUM OFF THREAD LENGTH spool full TILL CLAMP INSERTING SEWING END ->CL.SIDEW.

  • Page 86: Factory Settings For Special Parameters

    Beisler Automated Sewing Equipment Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Factory settings D.4.2 Factory settings for special parameters M01 Special parameters 2110-5: Pos. SEAM 01 - POCKET FACING Value Unit CLAMP POSITION RIGHT FOLDER SWING RELEASE INSERT SPEED CLAMP SPEED WAITING POSITION 1000...

  • Page 87: M01 Special Parameters 2111-5

    Short Seam Automat 2110-5 / 2111-5 Workinging Instructions Beisler Automated Sewing Equipment Factory settings D.4.2 Factory settings for special parameters M01 Special parameters 2111-5: Pos. SEAM 01 - POCKET FACING Value Unit CLAMP POSITION RIGHT FOLDER SWING RELEASE INSERT SPEED CLAMP SPEED WAITING POSITION 1200...

This manual is also suitable for:

2111-5

Table of Contents