TANDBERG MXP F8 Administrator's Manual page 166

MXP
Contents Introduction
MENU ADDRESS SETTINGS DESCRIPTION
Control Panel > FAR END CAMERA CONTROL
General > ON: The far end will be able to select your video sources, control the camera (pan, tilt, zoom) and request
snapshots
PERMISSIONS
OFF: The far end can access none of the features above on your system. You will however still be able to
control your camera, select your video sources and request snapshots.
Control Panel > FALLBACK TO TELEPHONY
This feature is only available for ISDN Networks.
General >
ON: Enables fallback from video calls to telephone calls.
PERMISSIONS
OFF: Disables fallback.
Control Panel > FAR END ISDN SYSTEM UPGRADE
General > ON: The system will allow a remote system to upgrade local software.
OFF: The system will not allow a remote system to upgrade local software.
PERMISSIONS
The remote software upgrade configuration can also be done via Telnet or the serial port:
xConfiguration RemoteSwUpgrade Mode: <On/Off>
Control Panel > MAXIMUM CALL LENGTH
Enter Maximum Call Length. Enter a value between 0-999 minutes:
General >
Value = 0: Enter the value 0 to disable the Maximum Call Length.
PERMISSIONS
Value = 1-999: Enter a value between 1-999 to enable Maximum Call Length.
Control Panel > PICTURE LAYOUT
General > PICTURE IN PICTURE (PIP): When you have selected PIP and you press the Layout button on the remote
control, this will result in an extra picture in smaller view (Picture in Picture). Press the Layout button to
SCREEN SETTINGS
move it around in the corners of the screen and finally hide it.
PICTURE OUTSIDE PICTURE (POP): When you have selected POP and you press the Layout button on
the remote control, you can see the images side-by-side, e.g. 1+1 layout, where the far end and near end
are displayed as images of equal size. Press again to see a 1+2 layout and a 1+3 layout and finally back
to full screen.
AUTO LAYOUT
Control Panel >
ON: When set to On the system will change layouts automatically depending on the number of participants in
General >
a call and if you have a dual stream or not.
SCREEN SETTINGS
OFF: When set to Off there will be no automatic layout changes during a call. All desired layout changes
must be done manually with the
D14033.06—AUGUST 2010
Getting started The menu structure The settings library The settings library
Layout button on the remote control.
Using the system Physical interfaces Peripheral equipment
INFORMATION
Lets you control if the other side (far end) should be allowed to
select your video sources and request snapshots.
When fallback is enabled, and the system fails to place a video
call it will attempt to place a telephone call to the same number
instead.
It is possible to upgrade software remotely, i.e. a far end system
may upgrade software on a local system via HTTP on ISDN*.
The system to be upgraded must be configured to allow remote
software upgrade. A
control the far end system to accomplish the software upgrade.
* Applies to systems with ISDN capabilities, e.g. this setting does
not apply to TANDBERG 1700 MXP.
This feature will automatically end both incoming and outgoing
calls when the call time exceeds the specified Maximum Call
Length in minutes.
The Picture Layout is related to the
remote control and it can be used at any time to change
the screen layout. For wide screen systems POP mode is
recommended. You will get optimized picture layouts for wide
screen by pressing the Layout button on the remote control.
TIP! Press and hold the Layout key on the remote control for one
second to hide the small picture directly from any position.
When receiving low resolution images (176 × 144 pixels
NOTE!
or less) the screen will automatically adjust to a smaller view to
give optimum quality experience.
The resolution 176 x 144 pixels is also known as QCIF.
Administrator Guide
Appendices Contact us
Remote Upgrade Password can be set to
Layout button on the
PRODUCT
All MXP
systems
with
controllable
camera
All MXP
systems
with ISDN
All MXP
systems
with ISDN
All MXP
systems
All MXP
systems
All MXP
systems
166