TANDBERG MXP F8 Administrator's Manual page 11

MXP
Contents Introduction Introduction
Safety Instructions
The following safety instructions applies to:
TANDBERG 8000 MXP
TANDBERG 6000 MXP Profile
TANDBERG Profile 52" with Codec 6000 MXP
TANDBERG 3000 MXP Profile
TANDBERG 1700 MXP
TANDBERG 1000 MXP
TANDBERG Edge 95/85/75 MXP
TANDBERG 990/880/770 MXP
TANDBERG 550 MXP
For your protection please read these safety
instructions completely before you connect the
equipment to the power source. Carefully observe all
warnings, precautions and instructions both on the
apparatus and in these operating instructions.
Retain this manual for future reference.
WATER AND MOISTURE
Do not operate the apparatus under or near water –
for example near a bathtub, kitchen sink, or laundry
tub, in a wet basement, near a swimming pool or in
other areas with high humidity.
•
Never install jacks for communication cables
in wet locations unless the jack is specifically
designed for wet locations.
•
Do not touch the product with wet hands.
CLEANING
Unplug the apparatus from communication lines,
mains power-outlet or any power source before
cleaning or polishing. Do not use liquid cleaners
or aerosol cleaners. Use a lint-free cloth lightly
moistened with water for cleaning the exterior of the
apparatus.
VENTILATION
Do not block any of the ventilation openings of the
D14033.06—AUGUST 2010
Getting started The menu structure The settings library
apparatus. Never cover the slots and openings with
a cloth or other material. Never install the apparatus
near heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that
produce heat.
Do not place the product in direct sunlight or close to
a surface directly heated by the sun.
LIGHTNING
Never use this apparatus, or connect/disconnect
communication cables or power cables during
lightning storms.
DUST
Do not operate the apparatus in areas with high
concentration of dust.
VIBRATION
Do not operate the apparatus in areas with vibration
or place it on an unstable surface.
POWER CONNECTION AND HAZARDOUS
VOLTAGE
The product may have hazardous voltage inside.
•
Never attempt to open this product, or any
peripherals connected to the product, where this
action requires a tool.
•
This product should always be powered from an
grounded power outlet.
•
Never connect attached power supply cord to
other products.
•
In case any parts of the product has visual
damage never attempt to connect main power,
or any other power source, before consulting
service personnel
•
The plug connecting the power cord to the
product/power supply serves as the main
disconnect device for this equipment. The power
cord must always be easily accessible.
•
Route the power cord so as to avoid it being
walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs,
receptacles and the point where the cord exits
from the apparatus.
Using the system Physical interfaces
•
Do not tug the power cord.
•
If the provided plug does not fit into your outlet,
consult an electrician.
•
Never install cables, or any peripherals, without
first unplugging the device from its power source.
Applies to: TANDBERG 3000 MXP Profile, Codec
3000 MXP, 1700 MXP, 1000 MXP, 990/880/770
MXP, 550 MXP
•
Always use the power supply (AC–DC adaptor)
provided with this product.
•
Replace only with power supply (AC–DC adaptor)
specified by TANDBERG.
•
Never connect attached power supply (AC–DC
adaptor) to other products.
SERVICING
•
Do not attempt to service the apparatus yourself
as opening or removing covers may expose you
to dangerous voltages or other hazards, and will
void the warranty. Refer all servicing to qualified
service personnel.
•
Unplug the apparatus from its power source and
refer servicing to qualified personnel under the
following conditions:
•
If the power cord or plug is damaged or
frayed.
•
If liquid has been spilled into the apparatus.
•
If objects have fallen into the apparatus.
•
If the apparatus has been exposed to rain or
moisture
A Class Declaration for TANDBERG 8000
声 明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING:
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
Administrator Guide
Peripheral equipment Appendices
•
If the apparatus has been subjected to
excessive shock by being dropped.
•
If the cabinet has been damaged.
•
If the apparatus seems to be overheated.
•
If the apparatus emits smoke or abnormal
odor.
•
If the apparatus fails to operate in accordance
with the operating instructions.
ACCESSORIES
Use only accessories specified by the manufacturer,
or sold with the apparatus.
COMMUNICATION LINES
Do not use communication equipment to report a
gas leak in the vicinity of the leak.
Applies to: TANDBERG 8000MXP,
TANDBERG Profile 52" with Codec 6000MXP,
3000MXP Profile, 1000MXP, 95/85/75MXP,
990/880/770MXP, 550MXP
•
Never touch uninstalled communication wires
or terminals unless the telephone line has been
disconnected at the network interface.
•
To reduce the risk of fire, use only No. 26 AWG or
larger telecommunication line cord (ISDN cables).
MXP
Contact us
6000MXP Profile,
11