Tuning Parameters - Omron 3G3MV-PDRT2 User Manual

Appendices
Note 1. When the control mode is changed, the Inverter will revert to default settings. (The V/F con-
trol default setting is given above.)
Note 2. The default setting is 0.1 for V/f control with PG.
Note 3. The default setting is 2.00 s for Inverters with a capacity of 55 kW or more.
Note 4. The same capacity as the Inverter can be set by initializing this parameter.
Note 5. The setting range for Asian models is 0 to 300.0
Note 6. The setting range for Asian models is 0 to 1.

Tuning Parameters

■
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
C1-01 0200 02
C1-02 0201 02
C1-03 0202 02
C1-04 0203 02
C1-05 0204 02
C1-06 0205 02
C1-07 0206 02
C1-08 0207 02
C1-09 0208 02
C1-10 0209 02
C1-11 020A 02
C2-01 020B 02
C2-02 020C 02
C2-03 020D 02
C2-04 020E 02
C3-01 020F 02
C3-02 0210 02
C3-03 0211 02
C3-04 0212 02
C3-05 0213 02
C4-01 0215 02
C4-02 0216 02
C4-03 0217 02
C4-04 0218 02
C4-05 0219 02
Name
At-
tribute
00 Acceleration time 1
01 Deceleration time 1
02 Acceleration time 2
03 Deceleration time 2
04 Acceleration time 3
05 Deceleration time 3
06 Acceleration time 4
07 Deceleration time 4
08 Deceleration Stop Time
09 Accel/decel time setting unit
0A Accel/decel time switching frequency
0B S-curve characteristic time at accelera-
tion start
0C S-curve characteristic time at accelera-
tion end
0D S-curve characteristic time at decelera-
tion start
0E S-curve characteristic time at decelera-
tion end
0F Slip compensation gain
10 Slip compensation primary delay time
11 Slip compensation limit
12 Slip compensation selection during
regeneration
13 Output voltage limit operation selection 0, 1
15 Torque compensation gain
16 Torque compensation primary delay
time constant
17 Starting torque value (forward) (See
note 4.)
18 Starting torque value (reverse) (See
note 4.)
19 Starting torque time constant (See note
4.)
Chapter 10
Setting Setting Default
range unit setting
0.0 to 0.1 s 10.0
6000.0 (Set with
(Set with C1-10.)
C1-10.)
0, 1 1 1
0.0 to 0.1 Hz 0.0
400.0
0.00 to 0.01 s 0.20
2.50
0.00 to 0.01 s 0.20
2.50
0.00 to 0.01 s 0.20
2.50
0.00 to 0.01 s 0.00
2.50
0.0 to 2.5 0.1 0.0 (See
note 1.)
0 to 1 ms 2000
10000 (See
note 1.)
0 to 250 1% 200
0, 1 1 0
1 0
0.00 to 0.01 1.00
2.50
0 to 1 ms 200 (See
10000 note 1.)
0.0 to 0.1% 0.0
200.0
−200.0 to
0.1% 0.0
0.0
0 to 200 1 ms 10
Write
during
opera-
tion
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
10-53