Protective Function Parameters - Omron 3G3MV-PDRT2 User Manual

Appendices
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
H5-04 0428 04
H5-05 0429 04
H5-06 042A 04
H5-07 042B 04
H6-01 042C 04
H6-02 042D 04
H6-03 042E 04
H6-04 042F 04
H6-05 0430 04
H6-06 0431 04
H6-07 0432 04
Note 1. The values in parentheses indicate initial values when initialized in 3-wire sequence.
Note 2. Set H5-01 to 0 to disable Inverter responses to RS-422A/485 communications.
Note 3. Values in parentheses are for Asian model Inverters.
Note 4. This parameter is not supported by the Asian model Inverters.

Protective Function Parameters

■
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
L1-01 0480 04
L1-02 0481 04
L1-03 0482 04
L1-04 0483 04
L1-05 0484 04
L2-01 0485 04
L2-02 0486 04
L2-03 0487 04
L2-04 0488 04
L2-05 0489 04
Name
At-
tribute
28 Stopping method after communication
error
29 Communication error detection selec-
tion
2A Send wait time
2B RTS control ON/OFF
2C Pulse train input function selection
2D Pulse train input scaling
2E Pulse train input gain
2F Pulse train input bias
30 Pulse train input filter time
31 Pulse train monitor selection
32 Pulse train monitor scaling
Name
At-
tribute
80 Motor protection selection
81 Motor protection time constant
82 Alarm operation selection during motor
overheating
83 Motor overheating operation selection
84 Motor temperature input filter time con-
stant
85 Momentary power loss detection
86 Momentary power loss ridethru time
87 Min. baseblock time
88 Voltage recovery time
89 Undervoltage detection level
Chapter 10
Setting Setting Default
range unit setting
0 to 3 1 3
0, 1 1 1
5 to 65 1 ms 5
0, 1 1 1
0 to 2 1 0
1000 to 1 Hz 1440
32000
0.0 to 0.1% 100.0
1000.0
−100.0 to
0.1% 0.0
100.0
0.00 to 0.01 s 0.10
2.00
1, 2, 5, 1 2
20, 24,
36
0 to 1 Hz 1440
32000
Setting Setting Default
range unit setting
0 to 3 1 1
0.1 to 5.0 0.1 min 1.0
0 to 3 1 3
0 to 2 1 1
0.00 to 0.01 s 0.20
10.00
0 to 2 1 0
0.0 to 2.0 0.1 s Depends
on
capacity.
0.1 to 5.0 0.1 s Depends
on
capacity.
0.0 to 5.0 0.1 s Depends
on
capacity.
150 to 1 V 190
210 (150 (380)
to 420) (See
(See note 1.)
note 1.)
Write
during
opera-
tion
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Write
during
opera-
tion
No
No
No
No
No
No
No
No
No
No
10-61