Toshiba G9 Installation And Operation Manual page 30

efesotomasyon.com -Toshiba inverter,drive,servo,plc
Terminal Descriptions
Note: The programmable terminal assignments may be accessed and changed from their
default settings as mapped on
Direct Access  Applicable Parameter Number. See the section titled
Mode Menu Navigation on pg. 46
numbers.

For further information on terminal assignments and default setting changes, see the
sections titled
Note: See the section titled
ASD conductor and terminal electrical specifications.
Note: Programmable terminals will not retain their settings indefinitely in the event of a
power loss. Connect an external +24 VDC supply to the SU+ terminal to retain the
programmable settings in the event of Control Power loss (see
ST — The default setting for this terminal is the Standby mode controller. As the default setting, this
terminal must be activated for normal system operation. The ST terminal is activated by connecting CC
to this terminal (Sink mode). When deactivated, OFF is flashed on the LED Screen and the Not-Ready-
to-Run indicator is displayed on the LCD Screen (see
programmed to any of the functions listed in
RES — The default setting for this terminal is Reset. The RES terminal is activated by connecting CC
to this terminal (Sink mode). A momentary connection to CC resets the ASD and any fault indications
from the display. Reset is effective when faulted only. This input terminal may be programmed to any
of the functions listed in
F — The default setting for this terminal is Forward run command. The F terminal is activated by
connecting CC to this terminal (Sink mode). This input terminal may be programmed to any of the
functions listed in
R — The default setting for this terminal is Reverse run command. The R terminal is activated by
connecting CC to this terminal (Sink mode). This input terminal may be programmed to any of the
functions listed in
S1 — The default setting for this terminal is Preset Speed 1 (see
terminal is activated by connecting CC to this terminal (Sink mode). This input terminal may be
programmed to any of the functions listed in
S2 — The default setting for this terminal is Preset Speed 2 (see
terminal is activated by connecting CC to this terminal (Sink mode). This input terminal may be
programmed to any of the functions listed in
S3 — The default setting for this terminal is Preset Speed 3 (see
terminal is activated by connecting CC to this terminal (Sink mode). This input terminal may be
programmed to any of the functions listed in
S4 — The default setting for this terminal is Preset Speed 4 (see
terminal is activated by connecting CC to this terminal (Sink mode). This input terminal may be
programmed to any of the functions listed in
RR — The default function assigned to this terminal is the Frequency Mode 1 setting. The RR
terminal accepts a 0 – 10 VDC input signal that is used to control the function assigned to this terminal.
This input terminal may be programmed to control the speed or torque of the motor via an amplitude
setting or regulate by setting a limit. The gain and bias of this terminal may be adjusted for application-
specific suitability (see
22
or via the Direct Access method: Program 
pg. 46
for the applicable Direct Access parameter

Terminal on pg. 47 and Default Setting Changes on pg.
Cable/Terminal/Torque Specifications on pg. 265
Table 5 on pg. 234
Table 5 on pg. 234 (see F114).
Table 5 on pg. 234 (see F111).
Table 5 on pg. 234 (see F112).
Table 5 on pg. 234
Table 5 on pg. 234
Table 5 on pg. 234
Table 5 on pg. 234
F210 – F215).
Program
74.
for the G9
Figure 20 on pg.
Figure 22. on pg. 31). This input terminal may be
(see F113).
Preset Speed 1 on pg.
(see F115).
Preset Speed 2 on pg.
(see F116).
Preset Speed 3 on pg.
(see F117).
Preset Speed 4 on pg.
(see F118).
G9 ASD Installation and Operation Manual
26).
83). The S1
83). The S2
84). The S3
84). The S4