Toshiba G9 Installation And Operation Manual page 288

efesotomasyon.com -Toshiba inverter,drive,servo,plc
Terminal Descriptions, 22
Time Limit For Lower-Limit Frequency Operation, 125
Torque, 44, 59
Torque Bias Input Selection, 143
Torque Command Selection, 154
Torque Control, 59, 60
Torque Current, 44
Torque Limit Settings, 60
Torque Reference, 44
Torque Speed Limiting, 60
Trace, 49, 50
Trace Cycle, 201
Trace Data 1, 201
Trace Data 2, 201
Trace Data 3, 202
Trace Data 4, 202
Trace Selection, 201
Traverse, 58
Traverse Acceleration Time, 233
Traverse Deceleration Time, 233
Traverse Jump Step, 233
Traverse Selection, 233
Traverse Step, 233
Trip Code, 44
Trip History, 253
Trip History (read-only), 50, 51
Trip Record at Monitor Screen, 253
Trip Settings, 53
Trouble Shooting, 244
Type Error, 250
Type Reset, 50, 79
U
U/T1, 16, 17
UC, 247
UL 1995, 254
Under-Voltage Trip, 187
Under-Voltage Trip Detection Time, 188
Under-Voltage/Ridethrough, 53
UP/DOWN Frequency (down) Frequency Step, 129
UP/DOWN Frequency (down) Response Time, 129
UP/DOWN Frequency (up) Frequency Step, 129
UP/DOWN Frequency (up) Response Time, 128
UP/DOWN Frequency Functions, 54
Up/Down Frequency Operation, 130
UP1, 252
UP2, 252
U-Phase Over-Current, 251
Upper Limit Frequency, 81
Upper-Limit Frequency, 71
User Notification Codes, 245
280
User Notification codes, 244
Utilities, 49
V
V/f 5-Point Setting Frequency 1, 101
V/f 5-Point Setting Frequency 2, 102
V/f 5-Point Setting Frequency 3, 103
V/f 5-Point Setting Frequency 4, 103
V/f 5-Point Setting Frequency 5, 104
V/f 5-Point Setting Voltage 1, 102
V/f 5-Point Setting Voltage 2, 103
V/f 5-Point Setting Voltage 3, 103
V/f 5-Point Setting Voltage 4, 103
V/f 5-Point Setting Voltage 5, 104
V/f Control Error, 248
V/f Pattern, 81
V/I, 21, 44, 54
V/I (V), 23
V/I Analog Input Broken Wire Detection Level, 189
V/I Input, 25
V/I Input Bias, 161
V/I Input Gain, 161
V/I Input Point 1 Frequency, 106
V/I Input Point 1 Rate, 107
V/I Input Point 1 Setting, 105
V/I Input Point 2 Frequency, 106
V/I Input Point 2 Rate, 108
V/I Input Point 2 Setting, 106
V/I Settings, 54
V/I Terminal, 44
V/T2, 16, 17
Vector Control, 13
Vector Motor Model, 59
Version (read-only), 51
VI/II Terminal, 44
Viewing Trip Information, 253
Virtual Input Terminal 1 Selection, 230
Virtual Input Terminal 2 Selection, 230
Virtual Input Terminal 3 Selection, 230
Virtual Input Terminal 4 Selection, 230
Voltage and Frequency Rating of the Motor, 71
Volts Per Hertz Setting, 72
V-Phase Over-Current, 251
W
W/T3, 16, 17
Warranty Card, 2
Wizard Finish, 73
W-Phase Over-Current, 251
G9 ASD Installation and Operation Manual