Page 1 Jetstream ® CPX-1000 Voice Services Platform TL1 Reference Release 2.5 Document No. 1000-A2-GH30-00...
Page 2 Copyright © 2003 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave.
Page 3: Table Of Contents
Preface Audience vii Organization vii Related Documents viii Chapter 1 TL1 Agent...1-1 Connections ...1-2 Configurable Options...1-2 User Administration...1-3 Command Scoping Rules...1-3 Grouping of Parameter Arguments ...1-4 Conventions and Notations...1-4 Chapter 2 Access Parameters...2-1 February 2003 Table of Contents Introduction Parameter Types AID ...2-1 ATAG ...2-2 CTAG ...2-2...
Page 4 Table of Contents Other Parameters ...2-3 AIDType ...2-3 AlarmCutoff Mode ...2-4 AlarmIndication Signal ...2-4 ATAGSeq ...2-5 Attenuation ...2-5 BoolYN ...2-5 BoolYNull...2-5 Cable ...2-6 CableType...2-6 ChannelGoTo ...2-6 ClearLog ...2-7 CommandMode ...2-7 CompressionType ...2-7 ConditionEffect ...2-8 ConditionType ...2-8 ControlState ... 2-11 ControlType ... 2-11 DgnRoutineTerm...2-12 Direction ...2-12 DSMode ...2-13...
Page 5 1000-A2-GH30-00 February 2003 Loopback ...2-19 LoopbackType ...2-19 LossBudget...2-20 MessageType...2-21 ModeofSwitch...2-21 MonitoredLevel ...2-22 MonitoredType ...2-22 MonitoredValue...2-22 NotificationCode...2-23 OCFacility ...2-23 ON_OFF ...2-23 Operation Category ...2-23 PrimaryState ...2-24 Redundancy ...2-25 ReportInterval ...2-25 SecondaryState ...2-25 ServiceEffect...2-26 SignalingType ...2-26 State...2-26 STSFacility...2-27 STSMap...2-28 ThresholdLevel...2-28 TimePeriod ...2-29 Timing...2-29 TimingReference...2-30 TransportType...2-30...
Page 6 Table of Contents Chapter 3 DSFacility ...3-3 Environment ...3-7 Equipment... 3-11 Fault ...3-27 IAD Provisioning ...3-42 TL1 Commands and Messages REPT ALM <DSnFacility>...3-3 RTRV-<DSnFacility>...3-5 REPT ALM ENV...3-7 RTRV-ALM-ENV...3-9 REPT ALM EQPT ... 3-11 REPT EVT EQPT...3-13 RTRV-EQPT...3-16 RTRV-IAD...3-17 RTRV-IADPORT ...3-20 RTRV-IADPRF ...3-21 RTRV-IG...3-23 RTRV-PROTGRP ...3-25...
Page 7 1000-A2-GH30-00 Log...3-50 OCFacility ...3-58 Protection ...3-63 Security ...3-63 STSFacility...3-72 System...3-74 Chapter 4 February 2003 INIT-LOG ...3-50 REPT DBCHG...3-52 RTRV-ATTR-LOG...3-53 RTRV-LOG ...3-54 RTRV-LOG-TL1LOG...3-56 SET-ATTR-LOG ...3-57 REPT ALM <OCFacility> ...3-58 RTRV-OC3 ...3-60 DLT-USER-SECU ...3-64 ED-PID...3-65 ED-SECU ...3-66 ED-USER-SECU ...3-67 ENT-USER-SECU ...3-69 RTRV-USER-SECU ...3-70 ACT-USER...3-74 ALW-MSG-<AIDType>...3-75 CANC-USER...3-76...
Page 8 Table of Contents Chapter 5 Index Environmental Alarm Types 1000-A2-GH30-00 February 2003...
Page 9 Audience The TL1 Reference is written for network operations center crafts personnel who manage and monitor alarms and events of the CPX-1000 equipment. These readers should know the command language interface and be familiar with TL1. Organization The TL1 Reference is organized as follows:...
Page 10 CPX-1000 Voice Services Platform Installation and Operation Describes the features, installation, testing, troubleshooting, and repair of the CPX-1000 Voice Services Platform equipment. JetCraft User’s Guide Describes the installation and use of JetCraft in CPX-1000 provisioning. JetVision Installation Describes the installation of JetVision software. JetVision User’s Guide Describes the top level management of multiple CPX-1000 equipment.
Page 11: Chapter 1 Introduction
Jetstream TL1 is based on the following Bellcore documents: TL1 Agent The TL1 Agent is an application that allows TL1 messages to be sent to the CPX-1000 Voice Services Platform. The messages supported allow for alarm management and retrieval of the current CPX-1000 configuration.
Page 12: Connections
1. Introduction Connections The TL1 Agent supports several simultaneous sessions to access information about the CPX-1000. You can access the TL1 Agent via TELNET or one of the serial ports on the MP card of the CPX-1000. Configurable Table 1–1 Options your setup and their default settings.
Page 13: User Administration
RWADM Read/Write Administration Retrieves (Request): To allow as much bulk and flexible retrieval of information from the CPX-1000, the fields of requests permit the following values and/or operators. — Fields with default values are optional and allow the wildcard value “ALL.” Where their syntaxes allow, these fields are listable and rangeable.
Page 14: Grouping Of Parameter Arguments
1. Introduction Grouping of Some parameters in a message can be grouped by using the Parameter ampersand (&) character so a single occurrence of a message may be applied to more than one entity. The grouping can be done to Arguments generate a list of AIDs or a range (incremented in integer steps) of AIDs.
Page 15 1000-A2-GH30-00 Table 1–3. Syntactical Characters February 2003 Character Description A semicolon indicates the end of a message. A comma separates parameters within a parameter block. A colon separates parameter blocks. – A dash is used to separate the first and second modifier.
Page 16 1. Introduction 1000-A2-GH30-00 February 2003...
Page 17: Chapter 2 Parameter Types
Parameters The Access Identification code (AID) directs an input command to its intended physical or data entity inside the CPX-1000. Equipment module and facilities are typical examples of entities addressed by the access code. The following table lists all AIDS used in TL1 messages by the CPX-1000.
Page 18: Atag
A message sent to an CPX-1000 may be addressed at that CPX-1000 or routed by it to its target CPX-1000. If an CPX-1000 is the only target possible for a message sent on a connection, then TID may be left out of that message. Otherwise, a TID must be specified.
Page 19: Other Parameters
This parameter indicates the type of Access Identifier (AID) for most non-environment messages. It defines the scope of AIDs for equipment (EQPT), the CPX-1000 as a whole (COM), and facility AIDs. The different facility AIDs have their own enums (i.e., AIDTypeOC, AIDTypeTn).
Page 20: Alarmcutoff Mode
2. Parameter Types AlarmCutoff This parameter indicates the mode of alarm cutoff (ACO) Mode operation that is provided by the CPX-1000. AlarmIndication This parameter indicates the type of Alarm Indication Signal (AIS) Signal to be sent on the outgoing cross-connected signal when AIS is on the incoming signal.
Page 21: Atagseq
1000-A2-GH30-00 ATAGSeq This parameter indicates the integral part of ATAG of the autonomous message to be retrieved. Valid values are integers that can be specified as listable and rangeable. Use a single asterisk (*) or double asterisks (**) to specify multiple or a range of values.
Page 22: Cable
2. Parameter Types Cable This parameter is used for provisioning analog service. CableType This parameter defines the type of cable used. ChannelGoTo ChannelGoTo is used for provisioning analog service. This parameter indicates the signaling state(s) to where the channel unit should go under system failure conditions.
Page 23: Clearlog
1000-A2-GH30-00 ClearLog This parameter controls the clearing of the log. CommandMode This parameter commands execution mode. CompressionType This parameter defines the type of compression used. February 2003 Note This parameter is reserved for a future release. Options Description Clear Delete NOCLR Do not clear the log Options...
Page 24: Conditioneffect
2. Parameter Types ConditionEffect This parameter lists the effect of the condition on the CPX-1000. ConditionType This parameter defines the list of conditions or alarms that occur on a CPX-1000 that includes Threshold Crossing Alerts (TCAs). Options Description A standing condition that has cleared.
Page 25 1000-A2-GH30-00 February 2003 Options Description CLKRECOVER Adaptive recovery scheme CPLOCCP Loss of connection CPXDOWN CPX is down DBERR Database error DS0READERR Software error in DS0 read DS1BLUE Received remote alarm signal – blue alarm DS1RED Received remote alarm signal – red alarm DS1YELLOW Received remote alarm signal –...
Page 26 Provisioned ports are greater than the reported ports Power fail RDI-L OAM line RDI RDI-P OAM path RDI READY Ready REBOOTERR CPX-1000 reboot error REBOOTING CPX-1000 rebooting Remote failure indication RXDTAINACT Rxdtainact TDMCLK No adapter is driving the TDM master clock UNEQ...
Page 27: Controlstate
1000-A2-GH30-00 ControlState This parameter defines the state of the external control. ControlType This parameter defines control types or external controls. February 2003 Note This parameter is reserved for a future release. Options Description Not applicable OPER Operated Released Note This parameter is reserved for a future release. Options Description AIRCOND...
Page 28: Dgnroutineterm
Testing stops immediately when failure is detected on a unit; then testing proceeds to other remaining equipment units. NORM The diagnostic terminates normally. The CPX-1000 completes the entire set of phases and iterations of the procedure regardless of failed phases. Options Description...
Page 29: Dsmode
1000-A2-GH30-00 DSMode This parameter defines the mode of operation of a DLC digroup. It may be NULL if not used. DSnFacility This parameter defines AID types for DS facility. Duration This parameter defines the duration of the external control operation. February 2003 Note This parameter is reserved for a future release.
Page 30: Echotype
2. Parameter Types EchoType This parameter defines the source of echo type. EnvConditionType This parameter lists the environmental condition. 2-14 Note This parameter is reserved for a future release. Options Description BOTH Both FARSIDE Far side NEARSIDE Near side No echo UNKNOWN Unknown Note...
Page 31: Equipmenttype
1000-A2-GH30-00 EquipmentType This parameter lists the type of equipment available. FacilityType This parameter lists the AID type for facility protection groups. February 2003 Options Description ATMOC3M ATM Optical Carrier 3 multi-mode ATMOC3S ATM Optical Carrier 3 Single-mode BRIDGE Bridge card COMPRESSION Compression card Central Processor card...
Page 32: Function_Restore
2. Parameter Types Function_Restore This parameter identifies the function or area within the CPX-1000 where restoration is allowed. IadPortType This parameter identifies the port type of the Integrated Access Device (IAD). 2-16 Note This parameter is reserved for a future release.
Page 33: Idle
1000-A2-GH30-00 Idle This parameter indicates the signal inserted from an idle DS. InhibitMode This parameter indicates whether a function is inhibited via an INH command. Interval This parameter defines the duration for which messages are logged. This parameter is expressed in value-unit (e.g., 1-day) format.
Page 34: Linecode
2. Parameter Types LineCode This parameter indicates the line code used. Location This parameter specifies the location of data and is used mainly for performance monitoring. LogName This parameter specifies the name of a log that is used for specific message categories.
Page 35: Loopback
This parameter indicates the remote DS2 loopback request mode. LoopbackType This parameter identifies the type of loopback operated or released by the CPX-1000. Depending on the transmission system, various parts of a signal may be looped back. For example, the LINE loopback may be a full metallic loopback, while a PAYLOAD loopback may result in a signal that has been recoded with new and different header and/or CRC information.
Page 36: Lossbudget
2. Parameter Types LossBudget This parameter specifies the category of optical interface specification based on loss budget. 2-20 Options Description FACIO Facility Input/Output LINE Line For support of the M23 Multiplex—7 DS2 Channel C-bit loopback NETWORK Network PAYLOAD Payload PORT Matrix loopback TERMINAL Terminal...
Page 37: Messagetype
1000-A2-GH30-00 MessageType This parameter specifies the type of autonomous message to be retrieved. Valid values are modifiers of any valid TL1 autonomous messages (e.g., DBCHG, ALM, and EVT messages). MessageType may be used together with ATAGSEQ or null. ModeofSwitch This parameter specifies the mode with which the command is to be implemented.
Page 38: Monitoredlevel
MonitoredType This parameter lists the counters that are monitored and/or kept in the CPX-1000. MonitoredValue This parameter specifies the value to which the register identified by the monitored type is to be initialized to or the measured value of a monitored parameter.
Page 39: Notificationcode
1000-A2-GH30-00 NotificationCode This parameter indicates the alarm level. OCFacility This parameter identifies the type of optical carrier equipment. Only 1 option is available: OC3—Optical carrier 3. ON_OFF This parameter indicates whether a switch, property, or other parameter or entity is set to ON or OFF. Operation This parameter specifies the operation category for the command Category...
Page 40: Primarystate
2. Parameter Types PrimaryState This parameter indicates the primary state and qualifier information of the entity. 2-24 Options Description Service billing Craft Interface Device Memory administration MGMT Network management MTCE System maintenance TRAF Traffic administration TSTG Service testing Options Description IS-ANR In-service, abnormal IS-NR...
Page 41: Redundancy
1000-A2-GH30-00 Redundancy This parameter indicates the redundancy of the equipment. ReportInterval This parameter specifies the reporting interval. Options include: 1-DAY; 1-HR; 12-HR; 15-DAY; 15-MIN; 30-MIN; and 31-DAY SecondaryState This parameter indicates the secondary state of the entity. Multiple values may be specified. February 2003 Note This parameter is reserved for a future release.
Page 42: Serviceeffect
2. Parameter Types ServiceEffect This parameter indicates the effect of the reported alarm on service. SignalingType This parameter indicates the signaling type. State This parameter is a combination of the primary and secondary states that indicate the maintenance state. Options AS-ANRST-SWTO IS-ANR-MTCELIMD IS-ANR-PWR...
Page 43: Stsfacility
1000-A2-GH30-00 Options IS-ANRST-PWR IS-ANRST-SGEO IS-ANRST-SWTI IS-NR-ACT IS-NR-BUSY IS-NR-IDLE IS-NR-INHIP IS-RST-SWTI IS-RST-SWTO OOS-AU-AINS OOS-AU-FLT OOS-AU-MEA OOS-AU-PWR OOS-AU-SGEO OOS-AU-UEQ OOS-AU-UEQ-MEA OOS-AURST-AINS OOS-MA-UAS OOS-MA-UEQ STSFacility This specifies the STS-1 type. Its option includes STS1. Only 1 option is available: STS1—Synchronous transport signal 1. February 2003 Description In service, abnormal and restricted, power...
Page 44: Stsmap
2. Parameter Types STSMap This indicates the type of mapping supported by the STS-p SPE. ThresholdLevel This parameter specifies the threshold value for the monitored type (montype). 2-28 Options Description ASYNC DS3 mapped to STS Asynchronous ATM signal (53 bytes) Data link transported in byte F2 of byte synchronous (SYNC) mapping.
Page 45: Timeperiod
This parameter is reserved for a future release. Options Description EXT1544 External 1.544 Mbps source EXT64 External 64 Kbps source Internal timing source. Use the CPX-1000 timing source defined by the TMG parameter for equipment. Loop timed THRU Through timed 2. Parameter Types...
Page 46: Timingreference
2. Parameter Types TimingReference This parameter indicates whether the termination is used as the primary or secondary timing source for the system. TransportType This parameter specifies the transport type. TroubleIsolated This parameter identifies the significance of the isolation information provided by the AID parameter included in the command message.
Page 47: Type
1000-A2-GH30-00 Type This parameter identifies the type of entity being provisioned. February 2003 Options Description Diagnostics in progress and will be returned in a separate message. AID identifies the units on which the diagnostics are being performed. ISLTD Isolated. The AID is a repairable or replaceable unit.
Page 48: Unassigned
2. Parameter Types Unassigned This parameter indicates the use of the unassigned (X) bits/bytes within the transport overhead. UserPrivilege This parameter specifies the access privileges for a CPX-1000 user. 2-32 Note This parameter is reserved for a future release. Options...
Page 49: Tl1 Commands And Messages
This chapter describes the TL1 commands and messages. Table 3–1 message used by the TL1 Agent. Table 3–1. TL1 Commands and Messages February 2003 TL1 Commands and lists the categories and names of the command and Categories Message/Command Names DSFacility REPT ALM <DSnFacility>...
Page 50 3. TL1 Commands and Messages Table 3–1. TL1 Commands and Messages (Continued) Categories Message/Command Names Fault REPT ALM IAD (page 3-27) REPT ALM IADPORT (page 3-29) REPT ALM IG (page 3-30) REPT ALM PROTGROUP (page 3-32) REPT EVT IAD (page 3-34) REPT EVT IADPORT (page 3-36) REPT EVT IG (page 3-37) REPT EVT PROTGROUP (page 3-39)
Page 51: Dsfacility
1000-A2-GH30-00 Table 3–1. TL1 Commands and Messages (Continued) DSFacility The DSFacility category includes these messages: REPT ALM <DSnFacility> Read only Security This message reports alarm condition on a DS (T1, T3) facility Description Related Messages February 2003 Categories Message/Command Names STSFacility RTRV-STS1 (page 3-72) System...
Page 52 CL (Clear) when this message signals the clearing of a condition. This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 53: Rtrv-
Description entity. REPT ALM <DSnFacility> Related Messages All Default errors. Errors Generation Figure 3–2. RTRV <DSnFacility> Format and Example February 2003 RTRV-<DSnFacility>:[TID]:<ds_id>: [CTAG]::[<type>]::[<pst>],[<sst>]; Input Format CPX-1000 98-06-20 14-30-00 001 COMPLD “AID:CLKMOD:AIS=Y,AISC=LOF,AISPASS=FONES, AIST=FONES,AISF=AISF,CMDMDE=FRCD,DLCID=DLCID, DS1TH=28,EQLZ=EQLZ,FENDNTE=NOTANSI,FLMDE=OG, FMT=DLC16,GOS=GOS,IDLE=QRSU,LBO=LBO, LINECDE=AMI,LPBK=INVSTF,MCOND=LOF,MODE=3, MONTYPE=BERP,PBIT=PBIT,PRTY=PRTY, RNPRTY=RNPRTY,SEQ=D4,SHELF=P,TACC=TACC, TMG=THRU,TMGREF=PRI,TPS=TPS,XBIT=XLAT, Note Not all parameters of a message are currently supported.

Page 54 3. TL1 Commands and Messages Table 3–3. Retrieve Parameters <DSnFacility> Parameters and Description Parameter Parameter Type ds_id type Type PrimaryState SecondaryState AlarmIndicationSignal aisc ConditionType cmdmde CommandMode rnprty Description This parameter identifies AID for the DSn equipment. ds_id is listable and rangeable. ds_id must not be null.
Page 55: Environment
1000-A2-GH30-00 Table 3–3. Retrieve Parameters <DSnFacility> Parameters and Description Parameter Parameter Type PrimaryState SecondaryState Environment The environment category includes these messages: REPT ALM ENV Read only Security Report Alarm Environment. This message reports a customer Description defined condition on an environmental alarm input. If an environmental condition is defined to be non-alarmed, then its occurrence or clearance is signaled with REPT-EVT.
Page 56 Date ocrtm Time conddescr REPT ALM ENV: [TID]: “<environmentid>:<ntfcncde>,<envcondtype>, [<ocrdat>],[<ocrtm>]null[<conddescr>]” Output Format CPX-1000 98-06-20 14-30-00 ** 001 REPT ALM ENV “ENV-AID:MJ,ENVCONDTYPE,04-1,12-00-00, \”DESC\”ENV-AID:MJ,ENVCONDTYPE,04-1,12-00- \”DESC\” Description This parameter indicates the AID Environment. This parameter indicates the notification code of the event that caused the condition to be reported.
Page 57: Rtrv-Alm-Env
ATTR -< ype> RTRV COND AIDT ATTR RTRV-ALM-ENV:[TID]: [<environmentid>]:[CTAG]::[<ntfcncde>], <envcondtype>; Input Format CPX-1000 98-06-20 14-30-00 001 COMPLD “ENV-AID:CR,ENVCONDTYPE,04-1,12-00-00,DESC” 3. TL1 Commands and Messages < acility> REPT ALM REPT ALM EQPT REPT ALM IADPORT REPT ALM PROTGROUP REPT EVT EQPT REPT EVT IADPORT REPT EVT PROTGRP -<...
Page 58 3. TL1 Commands and Messages Table 3–5. Retrieve Alarm Environment Parameters and Description Parameter Parameter Type environmentid ntfcncde NotificationCode envcondtype EnvConditionType ocrdat Date ocrtm Time description 3-10 Description This parameter indicates the AID of the environmental entity; it is listable and rangeable. If no value is specified, environmentid is equivalent to ALL.
Page 59: Equipment
1000-A2-GH30-00 Equipment The equipment category includes the following messages: REPT ALM EQPT Read only Security Description Report Alarm Equipment. REPT ALM messages are generated autonomously by a network element to report the onset or clearing of a standing condition that requires immediate attention. It does not signal environmental alarms that are signaled using REPT-ALM-ENV, and it does not signal non-alarmed conditions that are signaled with REPT-EVT.
Page 60 300 REPT ALM IG “GR303-1:CL,CCSPRI,NSA,06-09- Description This parameter identifies the entity in the CPX-1000 to which the command pertains. Access Identifier identifies an equipment unit, facility, link, packet link, or signaling link in the CPX-1000. eqpt_id is the AID equipment.
Page 61: Rept Evt Eqpt
REPT EVT EQPT Read only Security Report Event Equipment. This message is generated by the Description CPX-1000 to report non-alarmed events (e.g., the crossing of a performance threshold). Related Messages February 2003 Description This parameter indicates the effect on service caused by the standing or alarm condition.
Page 62 265 REPT EVT IGGR303-1:RXDTAINACT,TC,06-08- Description This parameter identifies the entity in the CPX-1000 to which the command pertains. Access Identifier identifies an equipment unit, facility, link, packet link, or signaling link in the CPX-1000. eqpt_id is the AID equipment. This parameter indicates the condition type for an alarm or a reported event.
Page 63 1000-A2-GH30-00 Table 3–7. Report Event Equipment Parameters and Description (Continued) Parameter Parameter Type ocrtm Time conddescr February 2003 3. TL1 Commands and Messages Description This parameter indicates the time when the specific event or violation occurred. This parameter describes the alarm or event condition.
Page 64: Rtrv-Eqpt
Related Messages All Default errors. Errors Generation Figure 3–7. Retrieve Equipment Format and Example 3-16 REPT ALM EQPT RTRV-EQPT: [TID]: “<equipmentId>:[TYPE=<type>],[PORTNB=<portnb>] [FIRMWARE=<firmware>],[SNUM=<snum>]: Input Format CPX-1000 98-06-20 14-30-00 001 COMPLD “AID:TYPE=T1,PORTNB=8,FIRMWARE=1.2, CLEI=JSSC12354,HWVER=123756, SNUM=1827674283,REDUNDANCY=PRIM:IS,BUSY” 1000-A2-GH30-00 REPT EVT EQPT Example February 2003...
Page 65: Rtrv-Iad
1000-A2-GH30-00 Table 3–8. Retrieve Equipment Parameters and Description Parameter Parameter Type equipmentId type EquipmentType portnb firmware snum PrimaryState RTRV-IAD Security Read only Retrieve IAD. This command retrieves information about an IAD. Description All Default errors. Errors Generation February 2003 3. TL1 Commands and Messages Description This parameter indicates the AID Environment and is listable and rangeable.
Page 66 Figure 3–8. Retrieve IAD Format and Example Table 3–9. Retrieve IAD Parameters and Description Parameter Parameter Type iadmodel ports 3-18 RTRV-IAD:[TID]:<IAD_id>:[CTAG]; Input Format CPX-1000 2000-06-12 05:46:59 1 COMPLD IAD-1:IADMODEL=Jetstream IAD- Flex,TAG1=company A,TAG2=DSLAM A,TAG3=SubscriberA, IG=GR303-1,SUB=cpxuser,SN=,PG=ATM1, PORTS=0,VPI=0,VCI=1,TRS=ATM,PST=OOS, Description This parameter specifies the IAD profile. iadprf is the AID IADPRF.
Page 67 1000-A2-GH30-00 Table 3–9. Retrieve IAD Parameters and Description (Continued) Parameter Parameter Type TransportType PrimaryState SecondaryState February 2003 3. TL1 Commands and Messages Description This parameter specifies the virtual path identifier (vpi). vpi is an integer and the valid entry is 0. This parameter specifies the virtual circuit identifier (vci).
Page 68: Rtrv-Iadport
Parameter Parameter Type port_id iadPort dialNumber 3-20 RTRV-IADPORT:[TID]:<port_id>:[CTAG]; Input Format CPX-1000 2000-06-08 10:43:41 1 COMPLD IADPort-1-1:CRV=1,IG=GR303-1, DIALNUMBER=, TYPE=VOICE,SIG=LOOP,COMPRESSION=NONE, ECHO=NO,PST=IS-NR, Description This parameter identifies the IAD port. port_id is the AID IADPort; it’s listable and rangeable. port_id must not be null.
Page 69: Rtrv-Iadprf
This parameter indicates the primary state of the entity. This parameter indicates the secondary state of the entity. sst is optional. RTRV-IADPRF:[TID]:<prf_id>:[CTAG]; Input Format CPX-1000 2001-02-15 10:08:18 71 REPT DBCHG /* 00001 */ CPX-1000 2001-02-15 10:08:18 1 COMPLD MOD=IAD802,PORT=24,SIG=GROUND,TRS=ATM, COMP=32KBP,ECHO=FARSIDE 3.
Page 70 3. TL1 Commands and Messages Table 3–11.Retrieve IAD Profile Parameters and Description Parameter Parameter Type prf_id port comp CompressionType echo EchoType 3-22 Description This parameter specifies the IAD profile. prf_id is the AID IADPRF. prf_id must not be null. This parameter specifies the IAD model. mod is a string and is optional.
Page 71: Rtrv-Ig
Figure 3–11. Retrieve Interface Group Format and Example Table 3–12.Retrieve Interface Group Parameters and Description Parameter Parameter Type IG_id igname switchmodel February 2003 RTRV-IG:[TID]:<IG_id>:[CTAG]; Input Format CPX-1000 2000-06-07 14:28:37 1 COMPLD GR303-1:IGNAME=ig1,SWITCHMODEL=Lucent-5ESS, LDS=lds1,PRIMEOC=CPX-1-1,PRIMEOCCHN=?--?, SECEOC=CPX-1-2,SECEOCCHN=?--?,PRIMTMC=CPX- 1-1, PRIMTMCCHN=?--?,SECTMC=CPX-1-2,SECTMCCHN=?- IGMEMBER=CPX-1-1&CPX-1-2&CPX-1-3&CPX-1- 4&CPX-1 -5 &CPX-1-6&CPX-1-7&CPX-1-8 Description This parameter identifies the Interface Group.
Page 72 3. TL1 Commands and Messages Table 3–12.Retrieve Interface Group Parameters and Description (Continued) Parameter Parameter Type primeoc primeocchn seceoc seceoccchn primtmc primtmcchn sectmc sectmcchn igmember 3-24 Description This parameter specifies the logical digital switch (LDS). lds is a string. This parameter specifies the primary Embedded Operations Channel (EOC).
Page 73: Rtrv-Protgrp
1000-A2-GH30-00 RTRV-PROTGRP Read only Security Retrieve Protection Group. This command retrieves information Description about a CPX-1000 Protection Group. All Default errors. Errors Generation Figure 3–12. Retrieve Protection Group Format and Example Table 3–13.Retrieve Protection Group Parameters and Description Parameter Parameter Type...
Page 74 3. TL1 Commands and Messages Table 3–13.Retrieve Protection Group Parameters and Description (Continued) Parameter Parameter Type bmember active 3-26 Description This parameter indicates the secondary member of a Protection Group. bmember is the AID DS. bmember is optional. This parameter indicates the active member of a Protection Group.
Page 75: Fault
1000-A2-GH30-00 Fault The fault category includes the following messages: REPT ALM IAD Security Read only Report Alarm IAD. This message reports a condition on an Description Integrated Access Device (IAD). Related Messages February 2003 REPT ALM IAD (page 3-27) REPT ALM IADPORT (page 3-29) REPT ALM IG (page 3-30) REPT ALM PROTGROUP (page 3-32) REPT EVT IAD (page 3-34)
Page 76 CL (Clear) when this message signals the clearing of a condition. This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 77: Rept Alm Iadport
RTRV COND AIDT ATTR REPT ALM IADPORT: [TID]: “<iadport_id>:<ntfcncde>,<condtype>,<srveff>, <ocrdat>,<ocrtm>,[<conddescr>]” Output Format CPX-1000 2001-02-22 16:07:23 ** 16 REPT ALM IADPORT “00001-1:MN,PORTMISMATCH,NSA,02-22-2001, 16:07:13,,,,,:PortNo 1 - Mismatched compression schemes: provisioned=16kbps, supported= None,,,:,” 3. TL1 Commands and Messages < acility> REPT ALM...
Page 78: Rept Alm Ig
CL (Clear) when this message signals the clearing of a condition. This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 79 CL (Clear) when this message signals the clearing of a condition. This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 80: Rept Alm Protgroup
3. TL1 Commands and Messages Table 3–16.Report Alarm Interface Group Parameters and Description (Continued) Parameter Parameter Type ocrtm Time conddescr REPT ALM PROTGROUP Read only Security Description Report Alarm Protection Group. This message reports a condition on a Protection Group. Related Messages 3-32 Description...
Page 81 CL (Clear) when this message signals the clearing of a condition. This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 82: Rept Evt Iad
Parameter Type ocrtm Time conddescr REPT EVT IAD Read only Security Report Event IAD. This message is generated by the CPX-1000 to Description report non-alarmed IAD events. Related Messages 3-34 Description This parameter indicates the time when the specific event or violation occurred.
Page 83 This parameter lists the conditions or alarms that occur on a CPX-1000. This parameter indicates the effect of the event based on the condition of the CPX-1000. This parameter indicates the date when the specific event or violation occurred. This parameter indicates the time when the specific event or violation occurred.
Page 84: Rept Evt Iadport
3. TL1 Commands and Messages REPT EVT IADPORT Read only Security Report Event IAD Port. This message is generated by the CPX-1000 Description to report a non-alarmed IAD port event. Related Messages Figure 3–18. Report Event IAD Port Format and Example 3-36 <...
Page 85: Rept Evt Ig
REPT EVT IG Read Only Security Report Event Interface Group. This message is generated by the Description CPX-1000 to report a non-alarmed Interface Group event. Related Messages February 2003 Description This parameter identifies the IAD port. iadport_id is the AID IADPORT.
Page 86 This parameter defines the list of conditions or alarms that occur on a CPX-1000. This parameter indicates the effect of the event based on the condition of the CPX-1000. This parameter indicates the date when the specific event or violation occurred.
Page 87: Rept Evt Protgroup
1000-A2-GH30-00 REPT EVT PROTGROUP Read only Security Report Event Protection Group. This message is generated by the Description CPX-1000 to report non-alarmed Protection Group events. Related Messages Figure 3–20. Report Event Protection Group Format and Example February 2003 < acility>...
Page 88: Rtrv-Alm-
<AIDType> Read only Security Retrieve Alarm. This command generates a report on the current Description state of alarm conditions within the CPX-1000. (The RTRV-COND command generates a report on both alarms and conditions.) Related Messages 3-40 Description This parameter identifies the Protection Group.

Page 89 2000,14:35:26,,,: MP Lost connection to CP,,,,, Description This parameter identifies the entity in the CPX-1000 to which the command pertains. alm_id is the AID ALL and is listable and rangeable. If no value is specified, alm_id is equivalent to ALL.
Page 90: Iad Provisioning
3. TL1 Commands and Messages Table 3–22.Retrieve Alarm Parameters and Description (Continued) Parameter Parameter Type srveff ServiceEffect entitytype AIDType ocrdat Date ocrtm Time conddescr The IAD provisioning category includes the following messages: Provisioning ENT-IAD Read/Write Security Description Enter IAD. This command creates a new Integrated Access Device (IAD).
Page 91 Table 3–23.Enter IAD Parameters and Description Parameter Parameter Type protgroup February 2003 ED-IAD:[TID]:<src>:[CTAG]:: [<ig>],[<protGroup>],[<vpi>], <vci>], [<transportType>],[<ports>],[<company>], [<dslam>],[<subscriber>],[<pst>]; Input Format CPX-1000 2001-02-14 17:48:52 6 REPT DBCHG /* 00001 */ CPX-1000 2001-02-14 17:48:52 1 COMPLD IAD-1 CPX-1000 2001-02-14 17:48:52 7 REPT DBCHG “DATE=2001-02-14,TIME=17-48- 52,USERID=cpxuser, DBCHGSEQ=1:ent-iad:::”...
Page 92 3. TL1 Commands and Messages Table 3–23.Enter IAD Parameters and Description (Continued) Parameter Parameter Type transport TransportType ports company dslam subscriber PrimaryState 3-44 Description This parameter specifies the virtual path identifier (vpi). vpi is an integer, and the valid entry is 0. This parameter specifies the virtual circuit identifier (vci).
Page 93: Ed-Iad
1000-A2-GH30-00 ED-IAD Read/Write Security Edit IAD. This command modifies an existing IAD. All fields are Description optional. All Default errors. Errors Generation Figure 3–23. Edit IAD Input Format Table 3–24.Enter IAD Parameters and Description Parameter Parameter Type protgroup February 2003 ED-IAD:[TID]: <src>:[CTAG]:: [<ig>],[<protGroup>],[<vpi>],[<vci>], [<transportType>],[<ports>],[<company>],...
Page 94 3. TL1 Commands and Messages Table 3–24.Enter IAD Parameters and Description (Continued) Parameter Parameter Type transport TransportType ports company dslam subscriber PrimaryState 3-46 Description This parameter specifies the virtual circuit identifier (vci). vci is an integer. The valid range is between 1 to 1024.
Page 95: Dlt-Iad
Errors Generation Identify the IAD to be modified. Figure 3–24. Delete IAD Format and Example February 2003 DLT-IAD:[TID]:<src>:[CTAG]; Input Format CPX-1000 2001-02-15 10:08:18 71 REPT DBCHG /* 00001 */ CPX-1000 2001-02-15 10:08:18 1 COMPLD /* IAD deleted */ CPX-1000 2001-02-15 10:08:18 72 REPT DBCHG “DATE=2001-02-15,TIME=10-08-...
Page 96: Ed-Iadport
All Default errors. Errors Generation Figure 3–25. Edit IAD Port Format and Example 3-48 ED-IADPORT:[TID]:<src>:[CTAG]:: [<crv>],[<signalingType>],[<compressionType>], Input Format CPX-1000 2001-02-21 11:29:57 23 REPT DBCHG /* 00001 */ CPX-1000 2001-02-21 11:29:57 1 COMPLD /* IAD port modified */ CPX-1000 2001-02-21 11:29:57 24 REPT DBCHG “DATE=2001-02-21,TIME=11-29-57,...
Page 97 1000-A2-GH30-00 Table 3–25.Edit IAD Port Parameters and Description Parameter Parameter Type Signaling SignalingType Compression CompressionType Echo EchoType Reference PrimaryState February 2003 3. TL1 Commands and Messages Description This parameter identifies the IAD to be modified. src is the AID IADPORT. This parameter specifies the call reference value (CRV).
Page 98: Log
3. TL1 Commands and Messages The CPX-1000 maintains logs of system events and messages. The logs allow CPX-1000 users to retrieve operational system information. The logs also provide historical information on commands and alarms that are useful in understanding the current and past system behavior.
Page 99 1000-A2-GH30-00 Figure 3–26. Initialize Log Format and Example Table 3–26.Initialize Log Parameters and Description Parameter Parameter Type log_id lognm LogName ocrdat Date ocrtm Time February 2003 INIT-LOG:[TID]: <log_id>:[CTAG]::<lognm>,<ocrdat>,<ocrtm>; Input Format INIT-LOG:TID:AID:CTAG::LOGNM,STADAT,STATM Description This parameter identifies the AID COM. Only two values accepted in the AID field: COM and NULL.
Page 100: Rept Dbchg
Report Database Change. This message reports immediately to the Description OS the CPX-1000 database changes that have occurred as a result of commands to change equipment provisioning or configuration. This message also includes changes to the value of the TID or SID,...
Page 101: Rtrv-Attr-Log
1000-A2-GH30-00 RTRV-ATTR-LOG Read only Security Retrieve Attribute Log. This command instructs the CPX-1000 to Description retrieve the current attributes for an existing log. The log contains attributes that govern the kind, length, and number of messages are logged. Related Messages All Default errors.
Page 102: Rtrv-Log
All Default errors. Errors Generation 3-54 RTRV-ATTR- LOG:[TID]:[<log_id>]:[CTAG]::[<lognm>]; Input Format CPX-1000 98-06-20 14-30-00 001 COMPLD “ALM,TRAF,15-DAY,123” Description This parameter identifies the source aid. log_id is the AID LOGID and is listable and rangeable. If no value is specified, log_id is equivalent to ALL.
Page 103 1000-A2-GH30-00 RTRV-LOG:[TID]:[<log_id>]:[CTAG]::[<lognm>]; Input Format agent> rtrv-log-tl1log:cpx-1000:all:1 CPX-1000 2001-01-03 11:51:02 1 COMPLD “ CPX-1000 2001-01-03 11:50:35 3 REPT ALM EQPT “CPX:CL,CPXDOWN,NSA,01-03-2001,11:49:38,,,,,:CPX is up,,,:,” ;” “ CPX-1000 2001-01-03 11:50:35 ** 12 REPT ALM EQPT “CPX-9:MJ,PEERCPMISS,SA,01-03-2001,11:50:27,,,,,:CP (slot 7) detected that the peer CP (slot 9) has been removed,,,:,”...
Page 104: Rtrv-Log-Tl1Log
3-56 INIT RTRV ATTR ATTR RTRV-LOG-TL1LOG:[TID]:<lognm>:[CTAG]; Input Format CPX-1000 98-06-20 14-30-00 001 COMPLD “RESPONSE” Description This parameter indicates the name of the log to be retrieve. lognm must not be null. This parameter indicates the name of the log being retrieved.
Page 105: Set-Attr-Log
1000-A2-GH30-00 SET-ATTR-LOG Read/Write Security Set Attribute Log. This command instructs the CPX-1000 to set the Description attributes associated with a message log. If a log already exists, the new values specified by the command replace the previous values. Related Messages All Default errors.
Page 106: Ocfacility
3. TL1 Commands and Messages Table 3–30.Set Attribute Log Parameters and Description Parameter Parameter Type log_id lognm LogName logdur Interval OCFacility This category contains these messages: REPT ALM <OCFacility> Read only Security Report OC3 Alarm. This message reports an alarm on an optical Description carrier facility.
Page 107 CL (Clear) when this message signals the clearing of a condition. This parameter lists conditions or alarms that occur on a CPX-1000. This parameter indicates the effect on service caused by the standing or alarm condition.
Page 108: Rtrv-Oc3
This parameter describes the alarm condition. conddescr is a string and optional. This parameter indicates the expected behavior whose deviation is described in obsdbhbr. exptdbhvr is a string and is optional. RTRV-OC3:[TID]:<oc_id>:[CTAG]; Input Format CPX-1000 2000-06-12 05:52:59 1 COMPLD CPX-11-1::FREQ=1550,IF=DROP,LINENO=14,,: OOS-AU,FAF 1000-A2-GH30-00 Example February 2003...
Page 109 1000-A2-GH30-00 Table 3–32.Retrieve OC3 Parameters and Description Parameter Parameter Type oc_id type Type aisnc NotificationCode BoolYN ferfnc NotificationCode BoolYN BoolYN February 2003 3. TL1 Commands and Messages Description This parameter specifies the AID for optical carrier facility. oc_id is the AID OC and is listable and rangeable.
Page 110 3. TL1 Commands and Messages Table 3–32.Retrieve OC3 Parameters and Description (Continued) Parameter Parameter Type lfebe BoolYN linecde LineCode montype MonitoredType protn BoolYN PrimaryState SecondaryState 3-62 Description This parameter indicates that performance monitoring data is to be gathered based on the LINE FEBE.
Page 111: Protection
Read only Security REPT SW (Report Switchover). This message is generated by the Description CPX-1000 after it switches an active card to standby and its mate to active. Figure 3–34. Report Switch Format and Example Table 3–33.Report Switch Parameters and Description...
Page 112: Dlt-User-Secu
The user cannot be deleted if he/she is logged on. USER USER SECU RTRV USER SECU DLT-USER-SECU:[TID]:<uid>:[CTAG]; Input Format CPX-1000 2000-06-06 19:05:02 1 COMPLD /* User 'user02' is deleted */ 1000-A2-GH30-00 CANC USER SECU USER SECU Example...
Page 113: Ed-Pid
USER USER SECU USER SECU RTRV USER SECU ED-PID:[TID]:<uid>:[CTAG]::<oldpid>,<newpid>; Input Format CPX-1000 2000-06-06 17:09:31 1 COMPLD /* Password changed */ CPX-1000 2000-06-06 17:09:31 53 REPT DBCHG “DATE=2000-06-06,TIME=17-09-31, USERID=user01, DBCHGSEQ=1:ED-PID:CPX-1000: user01:” 3. TL1 Commands and Messages CANC USER SECU...
Page 114: Ed-Secu
3. TL1 Commands and Messages Table 3–34.Edit Password Parameters and Description Input Parameters Description This is the user's identifier. uid is a string. oldpid This is the old password. oldpid is a string. newpid This is the user's new password. newpid is a string. ED-SECU Admin Security...
Page 115: Ed-User-Secu
1000-A2-GH30-00 Figure 3–37. Edit Security Format and Example Table 3–35.Edit Security Parameters and Description Input Parameters Description This parameter indicates AIDs affected. pid is a string. view This is a position-defined parameter that specifies the view (e.g., LI for subscriber line view). view is a string.
Page 116 Table 3–36.Edit User Security Parameters and Description Parameter Parameter Type UserPrivilege page 3-68 ED-USER-SECU: [TID]:<uid>:[CTAG]::[<pid>],[<cid>],[<uap>]: [PAGE=<page>]; Input Format CPX-1000 2000-06-06 18:03:39 2 COMPLD /* Editing done */ CPX-1000 2000-06-06 18:03:39 59 REPT DBCHG “DATE=2000-06-06,TIME=18-03- 39,USERID=user01, DBCHGSEQ=2:ed-user-secu:CPX-1000:user02:” Description This is the user's identifier. uid is a string.
Page 117: Ent-User-Secu
February 2003 USER USER SECU SECU RTRV USER SECU ED-USER-SECU: [TID]:<uid>:[CTAG]::[<pid>],[<cid>],[<uap>]: [PAGE=<page>]; Input Format CPX-1000 2000-06-06 17:25:26 2 COMPLD /* Editing done */ CPX-1000 2000-06-06 17:25:26 54 REPT DBCHG “DATE=2000-06-06,TIME=17-25- 26,USERID=user01, DBCHGSEQ=2:ed-user-secu:CPX-1000:user01:” 3. TL1 Commands and Messages CANC USER USER...
Page 118: Rtrv-User-Secu
Related Messages 3-70 Description This is the user's identifier that is unique to the CPX-1000. uid is a string. This is the user's password or private identifier. pid is a string. This is the channel ID consisting of up to 20 alphanumeric characters.
Page 119 An integer of up to 999, this interval is expressed in days, typically it’s 45 to 60 days. February 2003 RTRV-USER-SECU:[TID]:<uid>:[CTAG]; Input Format CPX-1000 2000-06-11 15:12:39 1 COMPLD user01:RWADM&RWALM:PAGE=14771, 3. TL1 Commands and Messages Example 3-71...
Page 120: Stsfacility
NotificationCode 3-72 RTRV-<STSFacility>:[TID]:<sts_id>: [CTAG];<type>:[AISNC=<aisnc>],[EXPTRC=<exptrc> [FEPM=<fepm>],[GOS=<gos>],[MONTYPE=<montype>], Input Format CPX-1000 2000-06-12 05:42:51 1 COMPLD CPX-1-1:STS1::IS,ACT Description This parameter identifies AID for synchronous transport signal entity. sts_id is the AID STS and is listable and rangeable. sts_id must not be null. This parameter identifies the type of entity being provisioned.
Page 121 1000-A2-GH30-00 Table 3–39.Retrieve STS1 Parameters and Description (Continued) Parameter Parameter Type exptrc fepm BoolYN montype MonitoredType yelnc NotificationCode PrimaryState SecondaryState February 2003 3. TL1 Commands and Messages Description This parameter indicates the expected path trace content. exptrc is a string of up to 64 ASCII characters and is optional.
Page 122: System
3. TL1 Commands and Messages System The system category includes the following messages: ACT-USER Read only Security Login. This command is used to login to a CPX-1000. Description Related Messages All Default errors. Errors Generation Figure 3–42. Login Input Format and Example...
Page 123: Alw-Msg-
Allow Event. This command permits or resumes the dispatch of Description automatic messages from the CPX-1000 that were inhibited by an INH-MSG call. Unreported alarms in existence at the time of restoration should be transmitted to the OS with the Report Alarm message.

Page 124: Canc-User
All Default errors. Errors Generation User's identifier. uid is a string. Figure 3–44. Logout Format and Example 3-76 act-user dlt-user-secu ed-pid ed-user-secu inh-msg-<aidtype> rtrv-user-secu CANC-USER:[TID]:<uid>:[CTAG]; Input Format CPX-1000 2000-06-06 16:46:21 1 COMPLD 1000-A2-GH30-00 alw-msg-<aidtype> ed-dat ed-secu ent-user-secu rtrv-hdr set-sid Example February 2003...
Page 125: Ed-Dat
ED-DAT Read/Write Security Edit Date and Time. This command allows the user to edit the date Description and/or time of the CPX-1000. Related Messages All Default errors. Errors Generation Figure 3–45. Edit Data and Time Format and Example Table 3–41.Edit Data and Time Parameters and Description...
Page 126: Inh-Msg-
INH-MSG- <AIDType> Not applicable Security Inhibit Message. This command instructs the CPX-1000 to disable Description the transmission of autonomous messages. This message affects all alarms for the Access Identifier specified. While autonomous message transmission is inhibited on the CPX-1000, standing and transitory conditions (alarmable and non-alarmable) are still posted against the appropriate CPX-1000 entities.

Page 127: Rtrv-Hdr
Read only Security Retrieve Header. This is a standard “keep-alive” message used to Description ping the CPX-1000. The header also returns the current time and TID of the CPX-1000 as part of a message. Related Messages Errors Generation All Default errors.
Page 128: Set-Sid
Related Messages All Default errors. Errors Generation Figure 3–48. Set System ID Format and Example 3-80 USER CANC USER -< ype> AIDT Source ID for the CPX-1000. sid is a string. SET-SID:[TID]::[CTAG]::<sid>; Input Format SET-SID:TID::CTAG::SID; 1000-A2-GH30-00 -< ype> AIDT RTRV Example...
Page 129: Error Codes
ENMD EQUIPAGE February 2003 For default error codes, go to For general error codes, go to error code CPX-1000 2000-06-06 16:47:19 1 DENY PIUI /* Can't login */ Error Message Not Valid for Access Type Not Equipped with Audit Capability...
Page 130 4. Error Codes Table 4–1. Default Error Codes (Continued) Error Code Error Type ENPM EQUIPAGE ENPS EQUIPAGE ENRI EQUIPAGE ENRS EQUIPAGE ENSA EQUIPAGE ENSI EQUIPAGE ENSS EQUIPAGE EQWT EQUIPAGE IBEX INPUT IBMS INPUT IBNC INPUT ICNC INPUT ICNV INPUT IDMS INPUT IDNC INPUT...
Page 131 1000-A2-GH30-00 Table 4–1. Default Error Codes (Continued) Error Code Error Type INAC INPUT INDV INPUT INUP INPUT IPEX INPUT IPMS INPUT IPNC INPUT IPNV INPUT ISCH INPUT ISPC INPUT ITSN INPUT MERR STATUS PICC PRIVILEGE PIFC PRIVILEGE PIMA PRIVILEGE PIMF PRIVILEGE PIRC PRIVILEGE...
Page 132 4. Error Codes Table 4–1. Default Error Codes (Continued) Error Code Error Type SAPR STATUS SARB STATUS SATF STATUS SCNA STATUS SCNF STATUS SDAS STATUS SDFA STATUS SDLD STATUS SDNA STATUS SDNC STATUS SDNR STATUS SDNS STATUS SFAS STATUS SFNS STATUS SLBM STATUS...
Page 133 1000-A2-GH30-00 Table 4–1. Default Error Codes (Continued) Error Code Error Type SNVS STATUS SPFA STATUS SPLD STATUS SPNA STATUS SPNF STATUS SRCI STATUS SROF STATUS SSRD STATUS SSRE STATUS SSTP STATUS STAB STATUS SVNS STATUS SWFA STATUS SWLD STATUS Table 4–2. General Error Codes Error Code (errcde) Error Type EANS...
Page 134 Error Message (errmsg) Not Terminate and Leave Red-Lined Circuit Software Program Does Not Support Command CPX-1000 Failure - Circuit Restored to Last Condition - Monitor or Terminate No Dial Tone Detected NTE Has Lost 16-KHz Byte Clock RTU Component or Configuration Error...
Page 135 1000-A2-GH30-00 Table 4–2. General Error Codes (Continued) Error Code (errcde) Error Type SACS STATUS SADC STATUS SADS STATUS SAMS STATUS SAOS STATUS SAPF STATUS SCAT STATUS SCBS STATUS SCIS STATUS SCNS STATUS SCOS STATUS SCSD STATUS SCSN STATUS SDBE STATUS SEOS STATUS SFYA...
Page 136 4. Error Codes Table 4–2. General Error Codes (Continued) Error Code (errcde) Error Type SNNS STATUS SNRS STATUS SNYA STATUS SOSE STATUS SOST STATUS SRAC STATUS SRAN STATUS SRCN STATUS SROS STATUS SRQN STATUS SRTN STATUS SRTO STATUS SSCE STATUS SSNG STATUS SSNP...
Page 137 Environmental Alarm Types This chapter lists and describes valid values for the alarm type (almtype) parameter. February 2003 Alarm Types Description AIRCOMPR Air compressor failure AIRCOND Air conditioning failure AIRDRYR Air dryer failure BATDSCHRG Air dryer failure BATTERY Battery failure CLFAN Cooling fan failure CPMAJOR...
Page 138 5. Environmental Alarm Types Alarm Types Description FUSE Fuse failure Generator failure HIAIR High airflow HIHUM High humidity HITEMP High temperature HIWTR High water INTRUDER Intrusion LWBATVG Low battery voltage LWFUEL Low fuel LWHUM Low humidity LWPRES Low cable pressure LWTEMP Low temperature LWWTR...
Page 139 ChannelGoTo characters, syntactical ClearLog February 2003 command list parameter grouping scoping rules CommandMode CompressionType ConditionEffect ConditionType configurable options connecting to the CPX-1000 ControlState 2-11 ControlType 2-11 conventions correlation tag (CTAG) Date and Time 3-77 DgnRoutineTerm 2-12 Direction 2-12 DLC digroup...
Page 140 Index ED-USER-SECU 3-67 ENT-IAD 3-42 ENT-USER-SECU 3-69 environmental alarm types EquipmentType 2-15 error codes default example general external control 2-11, 2-13 FacilityType 2-15 Fault 3-27 Function_Restore 2-16 general error codes IAD provisioning 3-42 IadPortType 2-16 Idle 2-17 InhibitMode 2-17 INH-MSG 3-78 INIT-LOG 3-50...
Page 141 1000-A2-GH30-00 REPT SW 3-63 RTRV RTRV-ALM 3-40 RTRV-ALM-ENV RTRV-ATTR-LOG 3-53 RTRV-EQPT 3-16 RTRV-HDR 3-79 RTRV-IAD 3-17 RTRV-IADPORT 3-20 RTRV-IADPRF 3-21 RTRV-IG 3-23 RTRV-LOG 3-54 RTRV-LOG-TL1LOG 3-56 RTRV-OC3 3-60 RTRV-PROTGRP 3-25 RTRV-USER-SECU 3-70 scoping rules SecondaryState 2-25 Security 3-63 serial port ServiceEffect 2-26 sessions, number allowed...

Paradyne Jetstream CPX-1000 Reference Manual

Chapter 1 Introduction

Chapter 2 Parameter Types

Chapter 3 TL1 Commands and Messages

Chapter 4 Error Codes

Quick Links

Related Manuals for Paradyne Jetstream CPX-1000

Summary of Contents for Paradyne Jetstream CPX-1000

Table of Contents