TransAct Ithaca 90PLUS Series Programmer's Manual page 114

Printer Control Codes
Control Codes Summary
Normal Second
ASCII field
ASCII
[ESC] [EM]W<n>
[ESC] #0
[ESC] %G
[ESC] %H
1
[ESC] *<m><n>
2
<n>
[ESC] !<n>
[ESC] -<n>
[ESC] 0
[ESC] 1
[ESC] 2
[ESC] 3<n>
[ESC] 4
[ESC] 5<n>
[ESC] 8
[ESC] 9
[ESC] :
[ESC] <
[ESC] ?<m><n>
[ESC] A<n>
[ESC] B
1 2
<n> <n>
...
3
<n>
k
<n> <0>
[ESC] C <n>
[ESC] D
1 2
<n> <n>
3
<n> ...
k
<n> <0>
[ESC] E
[ESC] F
[ESC] G
[ESC] H
Page 102
PcOS Series 90PLUS
Hex Code IPCL
Equivalent
code
1BH,19H,57H &%ZW<m
<m >
2
1BH,23H,30H &%QT
1BH,25H,47H &%MI
1BH,25H,48H &%CI
1BH,2AH
1BH,21H &%CS
<m ><m >
1 2
<m ><m >
3 3
1BH,2DH &%CU {n=0}
&%MU {n=1}
1BH,30H &%ST
1BH,31H &%SG
1BH,32H
1BH,33H &%SV
<m ><m >
1 2
<m >
3
1BH,34H &%ST
1BH,35H &%CA {n=0}
&%MA {n=1}
1BH,38H &%PF
1BH,39H &%PO
1BH,3AH &%F2
1BH,3CH &%PT
1BH,3FH
1BH,41H
1BH,42H
1BH,43H &%
1BH,44H
1BH,45H &%MM
1BH,46H &%CM
1BH,47H &%ME
1BH,48H &%CE
Rev Q
Programmer's Guide
Description
> Set eject-wait time.
1
Set normal print mode. (HSD is normal).
Begin italics.
End italics.
Print Epson 9-pin graphics in mode <m>.
Select International Character Set.
Begin/end underline mode.
n=0 end
n=1 begin
Set 1/8-inch line spacing.
Set 7/72-inch line spacing.
Begin variable line spacing. (Enable
[ESC] A n).
Set fine line space n/216 inch (defines
feed used by LF).
n=1...255
Set top of form.
Set automatic line feed.
n=0 end
n=1 begin
Disable paper-error sensing.
Enable paper-error sensing.
Set 12 cpi.
Set print suppress and pass-through.
Reassign graphic mode.
Set variable line spacing, n/72, enabled
by [ESC] 2. (n = 1...85)
Set vertical tabs. (Tabs are set at lines n
2 k
n ... n 0).
Set form length in lines or inches.
Set horizontal tabs. (Tabs are set at
1 2 k
columns n n ... n
value of n depends on the station
selected.
Begin emphasized print (half-speed).
End emphasized print.
Begin enhanced print (double-pass).
End enhanced print.
Page
67
26
41
41
50
28
39
22
23
23
22
24
25
60
60
35
76
50
23
1
24
25
20
0). The maximum
40
40
40
40
11/07/05