Table of Contents
Advertisement
Appendix A
Module Tags
Table 10 - Configuration Tags – 1732E-IB8M8SOER
Tag Name
Type
C.FilterOffOn
INT
C.FilterOnOff
INT
C.LatchEvents
BOOL
C.MasterSyncEn
BOOL
C.Pt0CaptureOffOn...Pt7CaptureOff
BOOL
On
C.Pt0CaptureOnOff...Pt7CaptureOn
BOOL
Off
Table 11 - Input Tags – 1732E-IB8M8SOER
Tag Name
Type
I.Fault
DINT
I.Data
SINT
I.NewData
SINT
84
Tags Used
Configuration, Input and Output Tags for 1732E-IB8M8SOER
Table 10
to
Table 12
generated in Studio 5000 Logix Designer software when you use your 1732E-
IB8M8SOER module.
Description
Sets the OFF to ON filter time for all 8 inputs. Times are set in µs increments of 0, 1000 (default), 2000, 4000, 8000
and 16000 µs.
0 = no filtering
For more information on Software Configurable Input Filters, see
Sets the ON to OFF filter time for all 8 inputs. Times are set in µs increments of 0, 1000 (default), 2000, 4000, 8000
and 16000 µs.
0 = no filtering
For more information on Software Configurable Input Filters, see
Latches events so that an event will not be overwritten until acknowledged.
0 = SOE not latched
1 = SOE latched (default)
Latched means that a sequence of events of LO to HI and HI to LO then LO to HI will cause the first LO to HI transition
to be recorded and the final LO to HI to be ignored. All subsequent transitions on that point will be ignored until
acknowledged/reset. If the bit is not set, the new LO to HI will overwrite the first LO to HI event immediately, even if the
controller has yet to extract that data.
PTP enabled bit indicates if the module is expected to sync to a master clock.
0 = Synchronization indication disabled (default)
1 = Synchronization indication enabled
If not enabled (0) then the Module Status Indicators will not flash green if we are not synched to a master clock.
Disabling the bit does not prevent the module from synchronizing to a master clock.
Enables capturing OFF to ON events on a per point basis. If disabled (0), that point will not record timestamp data for
OFF to ON input transitions.
0 = Capture disabled for OFF to ON input transitions
1 = Capture enabled (default) for OFF to ON input transitions
This option is useful if you want to avoid reporting data on the module for events in which you have no interest.
Enables capturing ON to OFF events on a per point basis. If disabled (0), that point will not record timestamp data for
ON to OFF input transitions.
0 = Capture disabled for ON to OFF input transitions
1 = Capture enabled (default) for ON to OFF input transitions
This option is useful if you want to avoid reporting data on the module for events in which you have no interest.
Set on Per Point
or Module-wide
Description
basis
Communication fault – The controller sets this tag to 1 for all 32 bits if a communication fault occurs on
Module-wide
the module otherwise all bits are zero.
Status of the input point. This data is filtered if the Input Filter feature is used on the module. Thus, an
input change must pass through the filter before it is seen in this tag.
Per point
0 = input is OFF
1 = input is ON
For example, if input 3 is ON, I.Data.3 = 1.
Flag indicating if new timestamp data was detected on the input.
0 = no new timestamp data on the input
1 = new timestamp data on the input (since last acknowledged)
Because input data for all inputs is sent the next RPI after each timestamped transition, this tag is
(1)
useful to quickly determine on which input the transition occurred. For example, if the module sends
Per point
new input data to the owner-controller and I.NewData.5 = 1, you know that at least one of the
timestamps for input 5 (I.Timestamp[5].OffOn or I.Timestamp[5].OnOff) has new data.
This tag only clears when the controller acknowledges the new data or all events on the module are
reset. For more information, see
Rockwell Automation Publication 1732E-UM003D-EN-E - November 2021
describe the configuration, input, and output tags
page
page
page
72.
52.
52.
Advertisement
Table of Contents
