Table of Contents
Advertisement
4.6
Power Consumption
Power Connection
Pin No.
1
(Valves and Outputs)
2
(Node and Inputs)
3
4
(Node and Inputs)
5
(Valves and Outputs)
Power Rating
•
For maximum supply current capability please refer to page 8-53.
Loads should not draw more than 0.5 Amps of current from any one individual discrete output point (Contact
•
factory for higher current capability requirements).
Component
Solenoid Valve Coil 501 (Each)
Solenoid Valve Coil 502 (Each)
Solenoid Valve Coil 503 (Each)
Solenoid Valve Coil 2002 (Each)
Solenoid Valve Coil 2005 (Each)
Solenoid Valve Coil 2012 (Each)
Solenoid Valve Coil 2035 (Each)
Solenoid Valve Coil ISO 5599/2 - SPA
Valve Adapter (Driver) 2000 Series
Valve Adapter (Driver) 500 Series
501 Series 32+ Valve Driver Board
502 Series 32+ Valve Driver Board
503 Series 32+ Valve Driver Board
Digital Module (M12 Style)
Digital Module (M8 Style)
Analog Module
Sub-Bus Hub
RTD Module
Communication Module (Node)
Sub-Bus Valve Module
580 Sub-Bus Valve Module
Auto Recovery Module (ARM)
ARM-Clip Module
Manual Configuration Module (MCM)
*
Current depends on graphic display brightness setting. Max. value shown with high brightness.
Values decrease by approx. 5% for Medium and 11% for Low brightness settings.
•
NOTE!
G3 Series PROFIBUS-DP
Function
0 VDC Common
0 VDC Common
Earth Ground
+24 VDC
+24 VDC
Voltage
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
24 VDC
Total power consumption for each Discrete I/O point is dependent on the specific
current draw of input sensor devices and output loads.
TDG3PTTM1-11EN
Subject to change without notice
www.asco.com
Technical Manual
TM
Description
0 VDC Voltage used to power outputs
(valve coils and discrete outputs) SW
0 VDC (-V) Voltage used to power
discrete inputs and node electronics UNSW
Protective Earth
Voltage used to power
discrete inputs and node electronics UNSW
Voltage used to power outputs
(valve coils and discrete outputs) SW
+24VDC
(Valves and Outputs)
Tolerance
Pins 1 & 5
Current
+10%/-15%
0.03 A
+10%/-15%
0.05 A
+10%/-15%
0.07 A
+10%/-15%
0.02 A
+10%/-15%
0.06 A
+10%/-15%
0.11 A
+10%/-15%
0.11 A
+10%/-15%
0.17 A
+/- 10%
0.03 A
+/- 10%
0.03 A
+/- 10%
0.03 A
+/- 10%
0.03 A
+/- 10%
0.03 A
+/- 10%
0.04 A
+/- 10%
0 A
+/- 10%
0.01 A
+/- 10%
0 A
+/- 10%
0.01 A
+/- 10%
0 A
+/- 10%
0 A
+/- 10%
0.034 A
+/- 10%
0 A
+/- 10%
0 A
+/- 10%
0 A
07/2020
+24VDC
(Node and Inputs)
Pins 2 & 4
Power
Current
Power
0.80 W
0 A
0 W
1.30 W
0 A
0 W
1.70 W
0 A
0 W
0.48 W
0 A
0 W
1.44 W
0 A
0 W
2.64 W
0 A
0 W
2.64 W
0 A
0 W
4.08 W
0 A
0 W
0.72 W
0.02 A
0.48 W
0.72 W
0.02 A
0.48 W
0.72 W
0.05 A
1.20 W
0.72 W
0.05 A
1.20 W
0.72 W
0.05 A
1.20 W
0.96 W
0.05
A*
1.20
W*
0 W
0.19 A
4.56 W
0.24 W
0.08
A*
1.92
W*
0 W
0.06
A*
1.44
W*
0.24 W
0.06
A*
1.44
W*
0 W
0.08
A*
1.92
W*
0 W
0.03
A*
0.72
W*
0.8 W
0.04
A*
0.9
W*
0 W
0.02 A
0.48 W
0 W
0.02 A
0.48 W
0 W
0.01 A
0.24 W
4-23
Advertisement
Table of Contents
