Quantum LTO 3 User Manual page 295

SRV_UNTHREAD_PULL_NO_STALL
SRV_UNTHREAD_PULL_UNEXPECTED_STALL
SRV_REEL_HW_DID_NOT_DETECT_STOP
SRV_PIN_GRABBER_PRE_INIT_STUCK_ZONE_A
SAS_INTERFACE_CTIO_ABORTED
SAS_INTERFACE_CTIO_CRCERROR
SAS_INTERFACE_CTIO_CRCERRORAUTOGOOD
SAS_INTERFACE_CTIO_CTIOM0SCBERR
SAS_INTERFACE_CTIO_CONNECTIONDOWN
SAS_INTERFACE_CTIO_DMAPARITYERROR
SAS_INTERFACE_CTIO_DATAPHASECRCERR
SAS_INTERFACE_CTIO_I_T_NEXUSLOSS
SAS_INTERFACE_CTIO_UNUSED
SAS_INTERFACE_CTIO_OKRESID
SAS_INTERFACE_CTIO_OKSTOP
SAS_INTERFACE_CTIO_OKSTOPAUTOGOOD
SAS_INTERFACE_CTIO_OPENTIMEOUT
SAS_INTERFACE_CTIO_PATHWAYBLOCKED
SAS_INTERFACE_CTIO_PEER_LOGOUT
SAS_INTERFACE_CTIO_XFERMISPECIFIED
SAS_INTERFACE_CTIO_XFERABORTEDCMD
SAS_INTERFACE_CTIO_WWNTABLEERR
SAS_INTERFACE_CTIO_WWNIOCOUNTERR
SAS_INTERFACE_CTIO_TASK_UNAVAIL
SAS_INTERFACE_CTIO_SHORTIU
SAS_INTERFACE_CTIO_SENDRESPSCBERR
SAS_INTERFACE_CTIO_SENDFRAMESCBERR
SAS_INTERFACE_CTIO_RETRY
SAS_INTERFACE_DETECT_WRITE_CRC_ERROR_AFT
ER_COMMAND_DONE
SRV_PIN_GRABBER_CANNOT_MOVE_OUT_TO_STA
NDBY
SRV_CMD_MEM_IS_NOT_COMPATIBLE_WITH_CNTR
L
DSM_WORM_SET_CAPACITY_NOT_ALLOWED
SCSI_DETECTED_WORM_CM_CONFLICT_IN_CART_T
YPE
SCSI_DETECTED_WORM_CM_CONFLICT_IN_MEDIA_
MFG_WORD
SCSI_DETECTED_WORM_CM_CONFLICT_IN_FORMA
T_TYPE
SRV_DOMAIN_ERROR
SCSI_SET_CAPACITY_NOT_ALLOWED_ON_INIT_WO
RM_CART
SCSI_WORM_MODE_NOT_SUPPORTED
CM_BAD_ERROR_USAGE
CM_BAD_CARTRIDGE_CONTENT
FC_INTERFACE_CTIO_ABORTED
MIC_CART_TYPE_NOT_RECOGNIZED
FC_INTERFACE_CTIO_CRCERROR
hub.
09C7h Servo Pulling tape to the cart reel didn't stall
09C8h Servo Pulling tape to cart reel stalled before the pin could reach the
grabber mover.
09C9h Servo This is an exception when HW does not detect stop condition
09CAh Servo Cannot move the pin grabber out of zone A to zone C2 during
pre-initialization.
09CBh SCSI Thread aborted by initiator
09CCh SCSI SDRAM CRC error
09CDh SCSI SDRAM CRC error after autogood sent
09CEh SCSI SAS_SSP_TGT_CtioM0Start out of rsrcs
09CFh SCSI Connection went down mid-transfer
09D0h SCSI DMA Parity error on Read
09D1h SCSI Data phase CRC error
09D2h SCSI I_T Nexus Loss Timer expired
09D3h SCSI Status not needed anymore
09D4h SCSI SSP_DL mismatch with autogood reqst
09D5h SCSI XferStop completed without errors
09D6h SCSI XferStop did full transfer+autogood
09D7h SCSI Open Timeout during open attempt
09D8h SCSI Pathway Blocked retries exhausted
09D9h SCSI Peer logged out while executing CTIO
09DAh SCSI XferData incorrectly specified
09DBh SCSI XferData attempted of aborted signal
09DCh SCSI Invalid WWN Table entry during Tx
09DDh SCSI WN I/O Count reached maximum value
09DEh SCSI Task not available
09DFh SCSI Short information unit received
09E0h SCSI SAS_SendRespFrame out of resources
09E1h SCSI SAS_SSP_SendFrame out of resources
09E2h SCSI OPEN_REJECT(RETRY) received. Retry.
09E3h SCSI Controller detect CRC error within SDRAM after send good
response to the host
09E4h Servo Cannot move pin grabber out to the standby position during
initialization.
09E5h Servo Controller and Servo both should have same shared memory
address space.
09E6h Data set Can't use SET_CAPACITY command on an initialized WORM
manager cartridge.
09E7h SCSI Some CM fields indicate WORM but cartridge type is not WORM.
09E8h SCSI Some CM fields indicate WORM but Media Manufacturer Info
page - media mfg word n
09E9h SCSI Some CM fields indicate WORM but Initialization Data page
Format Type field does
09EAh Servo Math Function out of domain
09EBh SCSI SET CAPACITY is not allowed on initialized WORM cartridges
09ECh SCSI Drive is not configured to support WORM
09EDh Medium CM Error Usage page
Auxiliary
Memory
09EEh Medium CM Cartridge Content page
Auxiliary
Memory
09EFh SCSI Thread aborted by initiator
09F0h Medium The Cartridge Manufacturer Information page cart type is not
Auxiliary recognized
Memory
09F1h SCSI SDRAM CRC error occurred during transfer.