Table of Contents
Advertisement
SRV_DIVIDER_TIMEOUT
SRV_SERVO_TIMEOUT
SRV_FIND_INDEX_FAILED
SRV_CAL_SLOT_FAILED
SRV_GOTO_POINT_INVALID
SRV_SERVO_POWEROFF_FAILED
SRV_REWIND_NOT_NECESSARY
SRV_NOT_USED_8
SRV_DIVIDER_OVERFLOW
SRV_MULTIPLY_ERROR
SRV_WRONG_REEL_SELECT
SRV_CMDPROC_UNDEFINED_SCRAMBLER_COMMA
ND
SRV_INVALID_MONITOR_MSG
SRV_SELF_MONITOR_BUF_OVERFLOW
SRV_SELF_EVENT_BUF_OVERFLOW
SRV_RTOS_UNKNOWN
SRV_SEQ_TABLE_LOOKUP
SRV_SEQ_NULL_FUNCTION_CALLED
SRV_SEQ_UNEXPECTED_MESSAGE_RESPONSE
SRV_SELF_ERROR_BUF_OVERFLOW
SRV_SEQ_NON_MECHANICAL_SCRAMBLER_COMM
AND
SRV_SEQ_OUT_OF_RANGE_SCRAMBLER_COMMAN
D
SRV_SELF_RTOS_BUF_OVERFLOW
SRV_CMDPROC_UNDEFINED_TASK_FOR_COMMAND
_IN_BYPASS_MODE
SRV_CMDTYPE_TABLE_INTEGRITY
SRV_REEL_NO_TASK_SPECIFIED
SRV_STACK_OVERFLOW
SRV_NO_SINECAL_DATA
SRV_BAD_SINECAL_DATA
SRV_NO_SINECAL_INDEX
SRV_NO_LOADRCA_INDEX
SRV_PARAM_TABLE_INTEGRITY
SRV_PARPORT_SCRAMBLER_NOT_READY_IN_SEND
_RESPONSE
SRV_PARPORT_UNDEFINED_CONDENSED_FORMAT
SRV_CMDPROC_NO_TAPE_TO_EJECT
SRV_CMDPROC_REJECT_EJECT_INVALID_STATE
SRV_STATUS_100
SRV_CMD_REJECT
SRV_CMD_ERROR
SRV_CMD_ABORTED
SRV_ALERT
SRV_MOVETAPE_ERROR_EOT_OVERRUN_DURING_
CRUISE_CONTROL
SRV_MOVETAPE_ERROR_BOT_UNDERRUN_DURING
_CRUISE_CONTROL
SRV_MOVETAPE_ERROR_EOT_OVERRUN_DURING_
RAMP_UP
SRV_MOVETAPE_ERROR_BOT_UNDERRUN_DURING
_RAMP_UP
SRV_INVALID_MARK_SELECT
ECC_C2_ERROR
MIC_NO_STATUS
MIC_PAGE_ID_BAD
DCh
Servo
FW timed out waiting for hardware divider
DDh
Servo
Servo firmware time out
DEh
Servo
Find drive motor index failed
DFh
Servo
Calibrate slot command failed
E0h
Servo
target point to close to ramp to or already past
E1h
Servo
servo did not acknowledge power off
E2h
Servo
current tape position is at or before wrap point.
E3h
Servo
E4h
Servo
division overflow when using hardware divider.
E5h
Servo
overflow error in scaled int multiply routine.
E6h
Servo
Wrong reel selected in rotate reel or stop reel command.
E7h
Servo
Command sent from scrambler is not defined.
E8h
Servo
internal RTOS message unknown.
E9h
Servo
fiq monitor to irq buffer overflow.
EAh
Servo
fiq event to irq buffer overflow.
EBh
Servo
unknown rtos error.
ECh
Servo
sequencer table look up error.
EDh
Servo
sequencer table function is null.
EEh
Servo
response not expected for command.
EFh
Servo
fiq error buf to irq buffer overflow.
F0h
Servo
non mechanical command received by sequencer.
F1h
Servo
out of range command received by sequencer.
F2h
Servo
fiq rtos buffer to irq buffer overflow.
F3h
Servo
undefined task specified.
F4h
Servo
table integrity for command type or parameter table look
F5h
Servo
reel task received a message without a valid sender specified.
F6h
Servo
stack overflow.
F7h
Servo
Sine calibration failed to find 0-xings.
F8h
Servo
Sine calibration found invalid 0-xings.
F9h
Servo
Sine calibration couldn't find index.
FAh
Servo
Sine RCA/RCB load couldn't find index.
FBh
Servo
Table lookup not consistent with COMMAND_ENUM definitions.
FCh
Servo
Scrambler not ready to accept command.
FDh
Servo
Undefined scrambler condensed format.
FEh
Servo
Eject attempt rejected because there was no tape.
FFh
Servo
Reject eject button due to invalid mechanical state.
100h
Servo
101h
Servo
Command rejected
102h
Servo
Command error
103h
Servo
Command aborted
104h
Servo
Servo Alert
105h
Servo
Tape has gone past eot during cruise control state
106h
Servo
Tape has gone past bot during cruise control state
107h
Servo
Tape has gone past eot during ramp up state
108h
Servo
Tape has gone past bot during ramp up state
109h
Servo
Invalid mode select in mark.c.
10Ah
ECC
10Bh
Medium
Fill Info.Word with this if there is no status to send.
Auxiliary
Memory
10Ch
Medium
the PAGE ID value received is out of RANGE.
Advertisement
Table of Contents
