Quantum LTO 3 User Manual page 259

SRV_CMDPROC_MANUFACTURER_ID_NOT_AVAILAB
LE
SRV_CMDPROC_LP1_NOT_AVAILABLE
SRV_CMDPROC_MFR_DATA_NOT_AVAILABLE_TAPE
_NOT_READ
SRV_CMDPROC_MFR_DATA_NOT_AVAILABLE_TAPE
_NOT_READY
SRV_SEQ_LOOP_UNDERRUN_CONDITION_IN_TABLE
SRV_REEL_SETTENSION_API_FAILED_DURING_WRA
P
SRV_BAD_PES_VALUES
SRV_CMDPROC_HEAD_OFFSET_NOT_ZERO_IN_WRI
TE_MODE
SRV_EXCEPT_RETURN_FROM_RTOS
SRV_TRACKING_NEVER_CALLED
SRV_NEVER_SAW_SERVO_SIGNAL
SRV_SERVO_SIGNALS_NOT_WITHIN_ACQUIRING_WI
NDOW
SRV_FAILURE_DURING_TRACKING_RAMPING
SRV_FAILURE_DURING_TRACKING_SETTLING
SRV_FAILURE_DURING_TRACKING_PRE_TRACKING
SRV_FAILURE_DURING_READING
SRV_FAILURE_DURING_WRITING
SRV_MOVETAPE_HEAD_POS_OUT_OF_RANGE
SRV_CMDPROC_ERROR_CODE_NOT_SUPPORTED_F
OR_SET_TRIGGER
SRV_CLOSED_LOOP_STEPPER_TIMEOUT_ATTEMPTI
NG_TO_FIND_PES
SRV_CMDPROC_SET_TRIGGER_REJECTED_TMUXSE
T_API_BUSY
SRV_MOTOR_LP1_OVERRUN
SRV_MOTOR_LP6_OVERRUN
SRV_MOTOR_EOT_OVERRUN
SRV_MOTOR_BOT_UNDERRUN
SRV_SEQUENCER_UNKNOWN_ALERT_RECEIVED
SRV_SZA_SIFT_COUNT_TOO_LARGE
SRV_RTOS_TASK_ID_ERROR
SRV_RTOS_NO_MEMORY_AVAILABLE
SRV_RTOS_MAILBOX_IN_USE
SRV_RTOS_ZERO_MESSAGE
SRV_RTOS_INVALID_SYSTEM_CALL
SRV_RTOS_NO_MESSAGE_PRESENT
SRV_RTOS_QUEUE_ID_ERROR
SRV_RTOS_QUEUE_FULL
SRV_STATEM_COMMAND_ABORTED_BY_EMERGEN
CY_EJECT
SRV_EMERGENCY_EJECT_ABORT
SRV_STEP_THREAD_TEST18_ERROR1
SRV_FINDZERO_INIT_API_REJECT
SRV_FINDZERO_ROUGH_RADIUS_API_REJECT
SRV_FINDZERO_PRECISE_RADIUS
SRV_FINDZERO_COARSE_MOTION_API_REJECT
SRV_MOVETAPE_RAMPDOWNTAPE_API_BUSY_REJ
41Eh Servo Manufacturer id not available
41Fh Servo LP1 value not available
420h Servo Manufacturer id not available.
421h Servo Manufacturer data not available
422h Servo Loop in sequencer table detected an invalid condition of current
state
423h Servo Settension API call failed during wrap tape operation
424h Servo
425h Servo Head offset is not zero while writing.
426h Servo Return from RTOS. Should never go here.
427h Servo
428h Servo
429h Servo
42Ah Servo
42Bh Servo
42Ch Servo
42Dh Servo
42Eh Servo
42Fh Servo invalid head position from stepper task
430h Servo Error code not supported for set trigger command.
431h Servo closed loop stepper timeout attempting to find pes
432h Servo Set trigger argument not supported
433h Servo LP1 underrun alert received in sequencer during command
processing
434h Servo This error happens when we are about to run off the end of tape.
We shut the re
435h Servo EOT overrun alert received in sequencer during command
processing
436h Servo BOT underrun alert received in sequencer during command
processing.
437h Servo Unknown error alert received in sequencer during command
processing.
438h Servo Sift values in READ SZA command exceed the number of
samples
439h Servo RTOS error
43Ah Servo RTOS error
43Bh Servo RTOS error
43Ch Servo RTOS error
43Dh Servo RTOS error
43Eh Servo RTOS error
43Fh Servo RTOS error
440h Servo RTOS error
441h Servo Command aborted by emergency eject
442h Servo Command aborted by emergency abort
443h Servo slack couldn't be taken up
444h Servo findzero init servo findzero api reject
445h Servo findzero: rough radius servo api reject
446h Servo findzero: precise radius servo api rejected
447h Servo findzero: coarse motion servo api rejected
448h Servo findzero rampdown api rejected during findzero operation