Quantum LTO 3 User Manual page 294

SRV_FLANGE_UNLOCKED_WITHOUT_CARTRIDGE
SRV_SERVO_ENUM_SPEED_OBSOLETE
SCSI_DRIVE_MODE_DOES_NOT_ALLOW_READ_WRI
TE_ACCESS_TO_WORM_MEDIA
SCSI_DRIVE_MODE_DOES_NOT_ALLOW_WRITE_AC
CESS_TO_WORM_MEDIA
SRV_EOT_CALC_DELTA_TOO_BIG
SRV_WW_INVALID_SET_COMMAND
SRV_CMDPROC_UNEXPECTED_MESSAGE_RESPON
SE
SRV_WW_INVALID_GET_COMMAND
SRV_CMDPROC_LOG_FULL
SRV_NOT_ALLOW_TO_WRITE_TO_SVO_OFFTRK_RE
G
SCSI_CLEANING_CARTRIDGE_CM_INVALID
ASSERTION_HARD_FAILURE
SRV_DAMPING_INPUT_FROZEN_FOR_N_FIQ
SCSI_INTERFACE_CDB_PHASE_RETRIES_EXHAUST
ED
SCSI_INTERFACE_DATA_PHASE_RETRIES_EXHAUS
TED
SCSI_INTERFACE_MAX_PARITY_RETRIES
SCSI_INTERFACE_RESELECT_TIMEOUT
SCSI_INTERFACE_BAD_MESSAGE_RECEIVED
SCSI_INTERFACE_BAD_IDENTIFY_MESSAGE_RECEI
VED
SCSI_INTERFACE_MAX_IDE_RETRIES
SCSI_INTERFACE_MAX_MESSAGE_RETRIES
SCSI_INTERFACE_NON_IDENTIFY_MESSAGE_RECEI
VED
SCSI_INTERFACE_UNEXPECTED_BUS_FREE
SCSI_INTERFACE_REJECT_MESSAGE_RECEIVED
SCSI_INTERFACE_UNEXPECTED_IDENTIFY_MESSAG
E_RECEIVED
SRV_FID_LPOS_NOTIFICATION_PASSED
SCSI_INTERFACE_ST_DATA_PARITY_RETRIES_EXH
AUSTED
SCSI_INTERFACE_DT_DATA_CRC_RETRIES_EXHAU
STED
SRV_TAPE_SPEED_REQUESTED_OUT_OF_RANGE
SAS_INTERFACE_CTIO_ACKNAK_TIMEOUT
SAS_INTERFACE_CTIO_INVALIDTTAG
SAS_INTERFACE_CTIO_WRITEOVERFLOW
SAS_INTERFACE_CTIO_NAK
SAS_INTERFACE_CTIO_DATAOFFSETERR
SAS_INTERFACE_CTIO_INITRESP_TIMEOUT
SAS_INTERFACE_CTIO_DATAPHASEERR
SRV_FAN_HIGH_TEMP_DETECTED
SCSI_UNKNOWN_MODE_PAGE_SUBPAGE
SRV_THREAD_UNEXPECTED_INTERNAL_MESSAGE
SRV_THREAD_UNABLE_TO_PICK_PIN
SRV_THREAD_UNABLE_TO_UNPICK_PIN
SRV_THREAD_UNPICK_STILL_HAS_PIN_AT_CHECK
SRV_THREAD_PULL_NO_STALL
SRV_THREAD_PULL_UNEXPECTED_STALL
099Bh Servo Flange is unlocked but there's no cartridge present
099Ch Servo Servo speed enum (2-7) will not be supported for Gen3HH or
later
099Dh SCSI worm control is in mode page 21, byte 4
099Eh SCSI worm control is in mode page 21, byte 4
099Fh Servo If the calcutation between last eot and current is too big
09A0h Servo
09A1h Servo
09A2h Servo
09A3h Servo
09A4h Servo Block writing of offtrk register
09A5h SCSI Cleaning cartridge CM is not valid
09A6h SCSI Hard error notification during interrupt context
09A7h Servo Input to the servo module from the sensor is not changing for N
FIQ count
09A8h SCSI SCSI Interface Error
09A9h SCSI Initiator Detected Error retry failure during DATA-IN Phase
09AAh SCSI SCSI Interface Error
09ABh SCSI SCSI Interface Error
09ACh SCSI SCSI Interface Error
09ADh SCSI SCSI Interface Error
09AEh SCSI SCSI Interface Error
09AFh SCSI SCSI Interface error
09B0h SCSI SCSI Interface Error
09B1h SCSI Drive went bus free at wrong time.
09B2h SCSI SCSI Interface Error
09B3h SCSI SCSI Interface Error
09B4h Servo We passed FID LPOS
09B5h SCSI ST DATA Parity Retry failure during DATA-OUT Phase
09B6h SCSI DT DATA CRC Retry failure during DATA-OUT Phase
09B7h Servo Min and max tape speed is limited to capability of mechanics
and / or electronic
09B8h SCSI ACK NAK Timeout returned by the lowlevel
09B9h SCSI CTIO Invalid Target Port Transfer Tag received by lowlevel
09BAh SCSI Write Overflow returned by lowlevel
09BBh SCSI NAK received by lowlevel
09BCh SCSI Data offset error returned by lowlevel
09BDh SCSI Initiator Response Timeout returned by lowlevel
09BEh SCSI Data phase error detected by lowlevel
09BFh Servo High temperature detected by ADC at a value of or greater than
53.9 C for 5 cons
09C0h Unknown Mode page Subpage
09C1h Servo An unexpected internal message is received by the load thread
task.
09C2h Servo Unable to pick the pin after enough retries.
09C3h Servo Unable to unpick the pin after enough retries.
09C4h Servo Pin is still inside the grabber after unpick
09C5h Servo Pulling tape to drive reel didn't stall
09C6h Servo Pulling tape to drive reel stalled before the pin could reach the