Table of Contents
Advertisement
N_ONE
SRV_VCM_HALL_SENSOR_IS_NOT_CALIBRATED_US
E_DEFAULT
SRV_UNTHREAD_UNPICK_EXCEEDED_RETRIES
SRV_REEL_SCREEN_TEST_REJECTED_CART_INSER
TED
SRV_REEL_SCREEN_TEST_BOTH_MOTORS_FAILED
SRV_REEL_SCREEN_TEST_DRIVE_MOTOR_FAILED
SRV_REEL_SCREEN_TEST_CART_MOTOR_FAILED
SRV_CMDPROC_MFR_DATA_NOT_AVAILABLE_CHE
CKSUM_BAD
SRV_THREAD_STALL_NEAR_PIN_GRABBER_MOVER
SRV_THREAD_STALL_NEAR_GUIDES
SRV_THREAD_STALL_NEAR_HEAD
SRV_THREAD_STALL_PAST_HEAD
TAPE_MFR_DATA_MISMATCH
TAPE_RSV_90E
TAPE_RSV_90F
DSM_CMPR_SKIP_INIT_BUFLIST_SHOULD_BE_EMPT
Y
DSM_CMPR_SKIP_TARGET_NOT_IN_DS
DSM_CMPR_USER_ADDR_OUT_OF_RANGE
DSM_CMPR_WR_UNDRUN_BUFLIST_RANGE_ERROR
DSM_CMPR_WR_INTERRUPT_NOT_RECOGNIZED
DSM_CANT_SWITCH_TO_READ_NO_DS
DSM_CMPR_READ_NO_DS_TO_SUPPLY
DSM_CMPR_RD_BUFFER_MISSING
DSM_CMPR_SKIP_ACCESS_PT_BUF_INDEX_OUT_OF
_RANGE
DSM_CMPR_SKIP_FAILED_TO_FIND_ACCESS_PT_B
UFFER
DSM_CMPR_SKIP_COULDNT_FEED_INTRA_DS_UND
ERRUN
SRV_DATA_BAND_ID_ERROR_DURING_HEAD_CALIB
RATION
SRV_UNTHREAD_STALL_NEAR_DRIVE_HUB
SRV_UNTHREAD_STALL_PAST_HEAD
SRV_UNTHREAD_STALL_NEAR_HEAD
SRV_UNTHREAD_STALL_NEAR_GUIDES
SRV_UNTHREAD_RETRY_PULLING_TAPE
SRV_UNTHREAD_PULLING_TAPE_EXCEEDED_RETRI
ES
SRV_THREAD_UNABLE_TO_LOCK_HUB
SRV_THREAD_RETRY_HUB_LOCK
SRV_THREAD_HUB_LOCK_EXCEEDED_RETRIES
SRV_UNPICK_NO_PIN
TAPE_CART_NOT_SUPPORT
SRV_HEAD_BRUSH_NEEDS_CART_LOADED_TO_CL
EAN
SRV_HEAD_BRUSH_HOME_NOT_CLEANING
SRL_INVALID_EVENT_ID_RECEIVED
902h
Servo
Exception when hall sensor is not calibrated
903h
Servo
Unable to unpick cartridge pin
904h
Servo
Reel motor screen test rejected because cartridge is inserted
905h
Servo
Both the drive motor and cart motor failed the screen test
906h
Servo
Drive motor failed the screen test, while cart motor passed
907h
Servo
Cart motor failed the screen test, while drive motor passed
908h
Servo
909h
Servo
Thread Stalled near Pin Grabber Mover
90Ah
Servo
Thread Stalled near First Guides
90Bh
Servo
Thread Stalled near Head
90Ch
Servo
Thread Stalled between the Head and the Drive Hub
90Dh
Tape
Auto Load detect Mfr Data from Servo and CM not match
90Eh
Tape
90Fh
Tape
910h
Data set
An unexpected situation occurred while initializing to skip to the
manager
target locati
911h
Data set
Data processor did not find target in specified dataset
manager
912h
Data set
Firmware error detected while either reading or locating
manager
913h
Data set
The number of buffers in the data compression engine was
manager
found to be incorrect d
914h
Data set
An invalid interrupt was detected during write.
manager
915h
Data set
The drive thinks it is positioned within a dataset, but when it
manager
comes time to st
916h
Data set
Attempt to supply a dataset to the decompressor fails, because
manager
there is no valid
917h
Data set
Part of a dataset appears to be missing.
manager
918h
Data set
Firmware calculation of access point buffer location resulted in
manager
a value which w
919h
Data set
While attempting to locate within a dataset, the buffer (partial
manager
dataset) which
91Ah
Data set
While locating to a target, a buffer (partial dataset) was found to
manager
be missing.
91Bh
Servo
Insufficient PES samples for data band ID after head offset
calibration
91Ch
Servo
Unthread Stalled near or in Drive Hub
91Dh
Servo
Unthread Stalled between the second guides and the Head
91Eh
Servo
Unthread Stalled between the second guides and the Head
91Fh
Servo
Unthread Stalled between the Pin Grabber Mover and the first
guides
920h
Servo
Unthread retry while pulling tape.
921h
Servo
Unthread exceeded retries while attempting to recover from an
error during Unthr
922h
Servo
Unable to lock inner hub to flange hub.
923h
Servo
Drive Inner Hub Lock retry.
924h
Servo
Unable to lock inner hub to flange hub.
925h
Servo
No pin detected during Unpick
926h
Tape
Cartridge not support, servo writer cartridge type (last 4 bytes)
are invalid
927h
Servo
HEAD_BRUSH command recieved when cartridge not loaded.
928h
Servo
BRUSH_HOME command recieved when not brushing
929h
General
Task is sending wrong event ID to display events
Advertisement
Table of Contents
