Quantum LTO 3 User Manual page 248

OWN_AT_LPOS_FROM_CRUISE_CONTROL_REVERS
E
SRV_MOVETAPE_INVALID_DIRECTION_IN_RAMP_DO
WN_AT_LPOS_FROM_CRUISE_CONTROL
SRV_MOVETAPE_LPOS_RECEIVED_BEFORE_TRACK
ING_IN_RAMP_UP_STATE
SRV_CMDPROC_TAPE_NOT_MOVING_FOR_REPOSIT
ION_CMD
SRV_MOVETAPE_REPOSITION_FAILED_ALREADY_P
AST_LPOS
SRV_CMD_INVALID_HEADPOSITION_SELECTED_LO
OKUP_TRACKING_RATIO
SRV_MOVETAPE_INVALID_TAPE_DIRECTION_IN_EN
ABLE_HEAD_BIAS_FOR_READ_TRACKING
SRV_MOVETAPE_INVALID_TAPE_DIRECTION_IN_EN
ABLE_HEAD_BIAS_FOR_WRITE_TRACKING
SRV_MOVETAPE_INVALID_TRACKING_MODE_IN_EN
ABLE_HEAD_BIAS
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_RAMP_UP
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_RAMP_UP
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_WAIT_MARK
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_WAIT_MARK
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_MARK_FOUND
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_MARK_FOUND
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_POSITION_TAPE
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_POSITION_TAPE
SRV_GOTO_LC_INITREELS_API_BUSY_REJECT
SRV_STEPPER_MOTOR_TASK_INVALID_OPERATION
SRV_STEP_LOAD_CART_ERROR1
SRV_STEP_LOAD_CART_ERROR2
SRV_STEP_LOAD_CART_ERROR3
SRV_STEP_LOAD_CART_ERROR4
SRV_STEP_LOAD_CART_DEFAULT
SRV_STEP_UNLOAD_CART_ERROR1
SRV_STEP_UNLOAD_CART_ERROR2
SRV_STEP_UNLOAD_CART_DEFAULT
SRV_STEP_THREAD_TAPE_ERROR1
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR1
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR2
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR3
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR4
SRV_STEP_THREAD_TAPE_ERROR6
SRV_STEP_THREAD_TAPE_ERROR7
SRV_STEP_THREAD_TAPE_ERROR8
SRV_STEP_THREAD_TAPE_ERROR9
SRV_STEP_THREAD_TAPE_ERROR10
SRV_STEP_THREAD_TAPE_ERROR11
SRV_STEP_THREAD_TAPE_ERROR12
SRV_STEP_THREAD_TAPE_ERROR13
in reverse direction.
24Eh Servo Tape not moving
24Fh Servo LPOS notification received before ramp up completed.
250h Servo Reposition cmd rejected
251h Servo LPOS already exceeded in reposition_from_idle
252h Servo Invalid head position selected in looking up tracking ratio
253h Servo Invalid tape direction was selected in enable head bias function
254h Servo Invalid tape direction selected in enable head bias function
255h Servo Invalid tracking mode selected in enable bias function
256h Servo Physical limit exceded during goto_lc_ramp_up state.
257h Servo Physical limit exceded during goto_lc_ramp_up state.
258h Servo Physical limit exceded during goto_lc_wait_mark state.
259h Servo Physical limit exceded during goto_lc_wait_mark_state.
25Ah Servo Physical limit exceded during goto_lc_mark_found state.
25Bh Servo Physical limit exceded during goto_lc_mark_found state.
25Ch Servo Physical limit exceded during position tape state.
25Dh Servo Physical limit exceded during position tape state.
25Eh Servo Init reels api call failed with a busy status.
25Fh Servo 32c
260h Servo Another event occurred before the cartridge in switch (SNS1)
tripped
261h Servo The cartridge load motor stalled before it reach it final position
262h Servo Expecting to see the cartridge in sensor change
263h Servo Expecting good completion status from cartridge load motor
task
264h Servo invalid state in process_load_cart function
265h Servo The firmware failed to hit SNS2 (switch on side of load mech)
266h Servo Error occurred while moving the loading tray past SNS2 (switch
on side of load m
267h Servo An unexpected state occurred in the cartridge unload task.
268h Servo fRemoving tape slack from the cartridge failed while Threading
269h Servo expecting SNS1 high
26Ah Servo expecting steps done
26Bh Servo expecting serial eeprom done
26Ch Servo expecting SNS1 low
26Dh Servo Load arm motor stalled while going to the cartridge.
26Eh Servo expecting steps done
26Fh Servo expecting MECH_DELAY1_DONE
270h Servo motor stall waiting for SNS13 high
271h Servo SNS13 Did not change to expected value
272h Servo motor stall waiting for ENGAGED_LEADER
273h Servo expecting steps done
274h Servo timer failure