Quantum LTO 3 User Manual page 288

GRABBER
SRV_UNTHREAD_MISSED_PIN_GRABBER
SRV_THREAD_UNABLE_TO_LOCK_DRIVE_HUB
SRV_THREAD_DRIVE_HUB_MAY_NOT_BE_LOCKED
SRV_THR_DRIVE_HUB_NOT_LOCKED
SRV_THREAD_UNABLE_TO_LOCK_DRIVE_FLANGE
SRV_REEL_NOT_USED4
SRV_REEL_NOT_USED5
SRV_REEL_CART_NOT_CHUCKED
SRV_REEL_DRIVE_HAS_STALLED
SRV_STEP_PIN_GRABBER_PCC_UNKNOWN_COMMA
ND
SRV_PORTION_NOTIFICATION_INVALID
SCSI_FW_IMAGE_DOWN_REV
SRV_VERSION_DOES_NOT_MATCH_PLATFORM_VER
SION
SRV_TRK_HEAD_AZIMUTH_TIMEOUT
SRV_MON_SDATA_TABLE_IS_FULL
SRV_REEL_REPOSITION_LPOS_NOT_WITHIN_RANG
E
SRV_REEL_REPOSITION_INVALID_STATE
SRV_DC_MOTOR_BUSY
SRV_DC_MOTOR_STALL
SRV_DC_CART_LOAD_PCC_UNKNOWN_COMMAND
SRV_DC_CART_LOAD_GAIO_WRITE_FAILED
SERVER_FAIL_TO_FREE_ELEMENT_DEQUEUE
SERVER_FAIL_TO_GET_FREE_ELEMENT_ENQUEUE
SERVER_FAIL_TO_GET_FREE_ELEMENT_QJAM
SERVER_FAIL_TO_GET_Q_ELEMENT_DEQUEUE
SERVER_NULL_SERVER_PTR_DEQUEUE
SERVER_NULL_SERVER_PTR_QPEEK
SERVER_NULL_TASK_PTR_ENQUEUE
SERVER_NULL_TASK_PTR_QJAM
SERVER_NULL_TASK_PTR_QSCAN
SRV_COMMAND_REJECTED_NO_SET_PARM_FOR_S
V_HEAD_AZIMUTH_SPECIFIC_PARAMS
SRV_COMMAND_REJECTED_NEED_FWD_TAPE_DIR_
BEFORE_REQUESTING_REV_TAPE_DIR
DSM_CMPR_WR_CMD_COMPLETE_LOST_BUFFER
DSM_CMPR_WR_ACCESS_PT_LOGIC_ERROR
DSM_CMPR_WR_XLATE_SENT_NULL_BUF
SERVER_RESERVED_0X08C4
SERVER_RESERVED_0X08C5
SERVER_RESERVED_0X08C6
SERVER_RESERVED_0X08C7
SERVER_RESERVED_0X08C8
SERVER_RESERVED_0X08C9
SRV_TRK_VCM_OFFSET_CALIB_BIAS_VALUE_NOT_
WITHIN_RANGE
SERVER_NULL_SERVER_PTR_ENQUEUE
SERVER_NULL_SERVER_PTR_QJAM
SERVER_NULL_SERVER_PTR_QSCAN
SERVER_RESERVED_0X08CE
SERVER_RESERVED_0X08CF
SERVER_RESERVED_0X08D0
SERVER_RESERVED_0X08D1
SERVER_RESERVED_0X08D2
8A1h Servo
8A2h Servo
8A3h Servo
8A4h Servo Unable to lock Drive Hub inner hub to outer hub.
8A5h Servo Unable to Lock the Drive Hub's Outer Flange prior to Unthread.
8A6h Servo
8A7h Servo
8A8h Servo Cartridge not fully chucked
8A9h Servo Take up Drive Reel stalled.
8AAh Servo Unknown Pin Grabber Stepper command
8ABh Servo
8ACh SCSI Microcode load failed, older revision not allowed.
8ADh Servo
8AEh Servo
8AFh Servo
8B0h Servo
8B1h Servo
8B2h Servo Dc motor pcc already busy
8B3h Servo Dc motor stalled
8B4h Servo Cart Load pcc recieved an unrecognized command
8B5h Servo Cart Load pcc unable to write to GAIO
8B6h General Can't free an element
8B7h General Can't get a free element for appending to server task list
8B8h General Can't get a free element for prepending to server task list
8B9h General Can't dequeue a task element
8BAh General Server Pointer points to an object instead of being NULL
8BBh General Server Pointer points to an object instead of being NULL
8BCh General Task Pointer points to an object instead of being NULL
8BDh General Task Pointer points to an object instead of being NULL
8BEh General Task Pointer points to an object instead of being NULL
8BFh Servo Need to set spec limits before executing
SVC_GET_HEAD_AZIMUTH command
8C0h Servo Must successfuly do SVC_GET_HEAD_AZIMUTH in fwd
direction before attempting rev
8C1h Data set DSM compressor access point logic lost buffer
manager
8C2h Data set DSM logic error detected while writing
manager
8C3h Data set DSM null buffer passed to translation routine while writing
manager
8C4h General
8C5h General
8C6h General
8C7h General
8C8h General
8C9h General
8CAh Servo During VCM offset calibration, bias value came up out of range
8CBh General Server Pointer points to NULL for ENQUEUE
8CCh General Server Pointer points to NULL for QJAM
8CDh General Server Pointer points to NULL for QSCAN
8CEh General
8CFh General
8D0h General
8D1h General
8D2h General