Quantum LTO 3 User Manual page 286

SRV_HEAD_STEPPER_SEARCHING_FOR_SERVO_BA
ND
THR_DIAG_UNKNOWN_COMMAND
SRV_NO_OPEN_LOOP_HEAD_POSITION_PRIOR_TO_
CLOSED_LOOP
THR_SEQ_BICELL_UNKNOWN_PARAMETER
THR_SEQ_UNKNOWN_COMMAND
SRV_TRK_VCM_GAIN_LOOP_EXCEEDED_RETRY_LI
MIT
SRV_REEL_MOTOR_OPEN_LOOP_VELOCITY_RUNA
WAY
SRV_REEL_MOTOR_OPEN_LOOP_POSITION_VELOCI
TY_RUNAWAY
DSM_COMMAND_SENDER_INVALID
SRV_SEQ_VCM_GAIN_LOOP_EXCEEDED_RETRY_LI
MIT
SRV_HEAD_STEPPER_WITHIN_TARGET_BUT_TOO_C
LOSE_TO_EDGE_OF_SERVO_BAND
SRV_CLOSED_LOOP_WRAP_POSITION_TOOK_LONG
ER_THAN_EXPECTED
SCSI_SAPI_IONA_TIMEOUT_FAILURE
TAPE_READ_FAILED_REREAD_PREVIOUS_WRAP
TAPE_READ_NO_EOD_DATASET_INVALID_CM_EOD_
PAGE
TAPE_READ_INVALID_EOD_PAGE
TAPE_RSV_854
TAPE_RSV_855
TAPE_RSV_856
TAPE_RSV_857
TAPE_RSV_858
TAPE_RSV_859
TAPE_RSV_85A
TAPE_RSV_85B
TAPE_RSV_85C
TAPE_RSV_85D
TAPE_RSV_85E
TAPE_RSV_85F
MON_INVALID_CHAN_DAT_VERSION
MON_DRIVE_NOT_CALIBRATED
MON_RSV_862
MON_RSV_863
MON_RSV_864
MON_RSV_865
MON_RSV_866
MON_RSV_867
MON_RSV_868
MON_RSV_869
MON_RSV_86A
MON_RSV_86B
MON_RSV_86C
MON_RSV_86D
MON_RSV_86E
MON_RSV_86F
SRV_INVALID_GAIO_REGISTER_ADDR
SRV_GAIO_REGISTER_ACCESS_IN_PROCESS
SRV_GAIO_READ_WRONG_ADDR
SCSI_IONA_ERR_NEGATIVE_ASPEN_Q_COUNT
844h Servo
845h General Threader Task received unknown Diagnostic command
846h Servo
847h General Bicell Select command had an unknown parameter
848h General Threader Task received an unknown command from the
Sequencer Task
849h Servo
84Ah Servo Reel Motor detected excessive velocity during Open Loop
Tension
84Bh Servo Reel Motor detected position exceeded limits.
84Ch Data set DSM received command from an unexpected or invalid task
manager
84Dh Servo
84Eh Servo
84Fh Servo Closed loop wrap position should not take longer than 500 ms
850h SCSI Unable to retrieve information from iona via PIO buffer
851h Tape Tape Read failed to reread at corner turn
852h Tape Tape Read: CM EOD Page is invalid and there is no EOD data set
on tape.
853h Tape Tape Read: Physical EOD Data Set does not match CM EOD
Page
854h Tape
855h Tape
856h Tape
857h Tape
858h Tape
859h Tape
85Ah Tape
85Bh Tape
85Ch Tape
85Dh Tape
85Eh Tape
85Fh Tape
860h Monitor Invalid Chan.dat version
861h Monitor Drive was not channel calibrated
862h Monitor
863h Monitor
864h Monitor
865h Monitor
866h Monitor
867h Monitor
868h Monitor
869h Monitor
86Ah Monitor
86Bh Monitor
86Ch Monitor
86Dh Monitor
86Eh Monitor
86Fh Monitor
870h Servo Gaio has 0-15 total of 16 registers
871h Servo
872h Servo
873h SCSI