Quantum LTO 3 User Manual page 257

SRV_OFF_TRACK
SRV_NO_PES_FOUND
SRV_VCM_SHOCK_ERROR
SRV_TRACKING_TARGET_OUTRANGE
SRV_TRACKING_SAMPLE_ERROR
SRV_TRACKING_COARSE_MOVE_ERROR
SRV_TRACKING_UPDATE_MEM_ERROR
SRV_MOVETAPE_RAMPDOWN_API_FAILED_IN_TRA
CKING_CMD_FAILED_HANDLER_IN_RAMP_UP_STAT
E
SRV_MOVETAPE_TRACKING_CMD_FAILED_IN_RAM
P_UP_STATE
SRV_CMDPROC_ROTATE_REEL_REJECTED_BECAU
SE_CART_LOADED
SRV_CMDPROC_ROTATE_REEL_REJECTED_BECAU
SE_DRIVE_REEL_IS_OBSTRUCTED
SRV_CMDPROC_ROTATE_REEL_REJECTED_INVALI
D_REEL_SELECT
SRV_CMDPROC_SET_DRIVE_STATE_COMMAND_RE
JECTED_STATE_OUT_OF_RANGE
SRV_STATEM_RECOVERY_COMMAND_REJECTED_D
RIVE_IN_UNKNOWN_STATE
SRV_TRKCNVT_MULTIPLY_ERROR_IN_TRACKING_C
ONVERT_FUNCTION
SRV_TRKCNVT_DIVIDE_ERROR_IN_TRACKING_CON
VERT_FUNCTION
SRV_STATEM_AUTOLOAD_COMMAND_REJECTED_I
NVALID_STATE
SRV_NOT_USED_OBSOLETE_2
SRV_STATEM_PRE_EJECT_COMMAND_REJECTED_I
NVALID_STATE
SRV_STATEM_PRE_EJECT_COMMAND_REJECTED_
DRIVE_IN_UNKNOWN_STATE
SRV_STATEM_AUTOLOAD_COMMAND_REJECTED_U
NKNOWN_STATE
SRV_TRKCNVT_DAC_OUTPUT_EXCEEDED_LIMIT
SRV_TRKCNVT_DAC_OUTPUT_BELOW_MINIMUM_LI
MIT
SRV_STEP_HEAD_EXPECTING_BOTTOM_SENSOR_H
IGH
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_BOTT
OM_SENSOR_HIGH
SRV_STEP_HEAD_EXPECTING_BOTTOM_SENSOR_L
OW
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_BOTT
OM_SENSOR_LOW
SRV_SZA_INTERFACE_BUSY
SRV_SZA_FUNCTION_ACTIVE
SRV_SZA_REGISTER_INVALID
SRV_SZA_READ_COUNT_TOO_LARGE
SRV_SZA_WRITE_COUNT_TOO_LARGE
SRV_SZA_WRITE_DATA_INVALID
SRV_REEL_CARTDITHER_API_CALL_FAILED_INVALI
D_STATE
SRV_SERIAL_EEPROM_FAILED
SRV_SRV_RTOS_INVALID_TASK_ID_SPECIFIED
SRV_MOTOR_POWER_FAIL_1
SRV_MOTOR_POWER_FAIL_2
SRV_MOTOR_POWER_FAIL_3
3CDh Servo tracking servo detected off track event
3CEh Servo no valid PES event
3CFh Servo tracking servo detected shock vibration error
3D0h Servo tracking servo detected unreachable track error
3D1h Servo tracking servo detected asic sample error
3D2h Servo tracking servo detected coarse stepper is out of position
3D3h Servo tracking servo detected PES memory failure
3D4h Servo Rampdown api call failed/rejected when called from tracking
command failed handl
3D5h Servo Tracking command failed in ramp up state
3D6h Servo Rotate reel command rejected because cartridge is loaded and
command is trying
3D7h Servo Rotate reel command rejected because reels are obstructed by
tape or a cartridge
3D8h Servo Rotate reel command rejected because an invalid reel select was
given
3D9h Servo Set drive state command rejected because the drive state is out
of range.
3DAh Servo Recovery command rejected
3DBh Servo Multiply error in tracking conversion function from ratio to dac
3DCh Servo Divide error in tracking conversion function from dac to ratio.
3DDh Servo Command rejected since the drive state was invalid (out of
range).
3DEh Servo Command rejected since the drive state was invalid in eject
sequence
3DFh Servo Command rejected since the drive state was invalid in pre-eject
sequence
3E0h Servo Command rejected
3E1h Servo Command rejected
3E2h Servo Calculated DAC tracking target greater than maximum input
3E3h Servo Calculated DAC tracking target less than minimum input
3E4h Servo expecting SNS9 high
3E5h Servo expecting SNS9 low
3E6h Servo expecting stepper to halt after SNS9 high
3E7h Servo expecting stepper to halt after SNS9 low
3E8h Servo interface to SZA chip busy for too long
3E9h Servo SZA read or write already in progress
3EAh Servo request to read invalid SZA register number
3EBh Servo amount of SZA read data exceeds buffer size
3ECh Servo amount of SZA write data exceeds buffer size
3EDh Servo SZA write data contains invalid reg or chip ID
3EEh Servo Call to cartDither api failed
3EFh Servo
3F0h Servo invalid task specified in rtos wrapper function.
3F1h Servo no power to reel motor circuits on startup
3F2h Servo no power to reel motor circuits after POR clear
3F3h Servo no power to reel motor circuits after PF clear