Table of Contents
Advertisement
ALID_STATE
SRV_CMDPROC_CMD_REJECT_SEQUENCER_BUSY_
AND_BUFFER_FULL
SRV_CANNOT_INSERT_INTO_LPOS_NOTIFY_TABLE_
UNTIL_SCR_AND_WP_FOUND_LP1
SRV_LPOS_ROLLOVER_DETECTED_FROM_CM_PHY
S_LP1
SRV_LPOS_ROLLOVER_DETECTED_FROM_WP_CAL
C_PHYS_LP1
SRV_LPOS_TOP_SERVO_AND_BOTTOM_SERVO_CA
LC_LP1_NOT_WITHIN_TOLERANCE
SRV_REEL_MOT_PWR_FAIL_DETECTED
SRV_REEL_MOT_EXCESSIVE_CURRENT_DEMAND_D
ETECTED
SRV_FINDZERO_TIME_OUT
SRV_FINDZERO_STATE_VARIABLE_OUT_OF_RANGE
SRV_FINDZERO_COARSE_OR_APPROACHING
SRV_FINDZERO_INDEX_SETUP_API_REJECT
SRV_FINDZERO_INDEX_HOME_API_REJECT
SRV_FINDZERO_HOME_DRIVE_REEL_API_REJECT
SRV_FINDZERO_APPROACHING_API_REJECT
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COA
RSE_MOTION
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COM
PLETE
SRV_CMDPROC_FIND_INDEX_FAILED_WRITING_TO_
LINEAR_COUNTER_API_BUSY
SRV_CMDPROC_LINEAR_COUNTER_NOT_RECORDE
D_PREVIOUSLY
SRV_SEQ_POWER_ON_INIT_FAILED_WRITING_TO_LI
NEAR_COUNTER_API_BUSY
SRV_CMDPROC_INVALID_STATE_FOR_RAMP_HEAD
_COMMAND
SRV_CMDPROC_TAPE_NOT_MOVING_FOR_RAMP_H
EAD_COMMAND
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_CHANGE_TRACKING_MODE
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_WRAP_RESTART_TRACKING
SRV_MOVETAPE_SET_LC_NOTIFICATION_FAILED
SRV_CMDPROC_REJ_TAPE_NOT_READY
SRV_STEP_HEAD_EXPECTING_MOVING_UP_WITH_A
DDED_HYSTERESIS_AFTER_REFERENCE_SENSOR_
HIGH
SRV_CMD_INVALID_COMMAND_CALLED_SEQUENC
E_IS_NULL
SRV_TIMEOUT_DURING_HEAD_STEPPER_STOPPING
_AFTER_SEARCHING_FOR_SERVO_BAND
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_
UP_WITH_ADDED_HYSTERESIS_AFTER_REFERENC
E_SENSOR_HIGH
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND
SRV_STEP_HEAD_EXPECTING_HYSTERESIS_BEFOR
E_SEARCHING_FOR_SERVO_BAND_IN_OTHER_DIRE
CTION
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND_IN_OTHER_DIRECTION
SRV_STEP_HEAD_EXPECTING_STOPPING_AFTER_F
AILING_SEARCH_FOR_SERVO_BAND_IN_OTHER_DI
range).
613h
Servo
Command rejected since the sequencer was processing an error
and the polled buff
614h
Servo
LPOS values in the notification table are dependent on CM_LP1
and WP_LP1.
615h
Servo
Calc phy LP7 from CM phys LP1 is greater then LTO spec
616h
Servo
Calc phy LP7 from WP calc phys LP1 is greater then LTO spec
617h
Servo
The LP1 value calc for top servo didn't match the LP1 value calc
for the bottom
618h
Servo
12 volt power reset detected
619h
Servo
Excessive current detected on motor
61Ah
Servo
Time out occured waiting for servo response
61Bh
Servo
Find zero wrap state variable out of range.
61Ch
Servo
Find zero wrap coarse or approaching api rejected call.
61Dh
Servo
Find zero wrap index setup api rejected call.
61Eh
Servo
Find zero wrap index home api rejected call.
61Fh
Servo
Find zero wrap home drive reel api rejected call.
620h
Servo
Find zero wrap approaching zero api rejected call.
621h
Servo
Find zero wrap coarse exceeded coarse motion retries.
622h
Servo
Find zero wrap retries exceeded after completion.
623h
Servo
Reset linear counter to remember the aligned slot position
624h
Servo
Linear counter not reset with RECORD ALIGNED SLOT
command prior to this command
625h
Servo
Reset linear counter failed during power on recovery
626h
Servo
Ramp head command rejected
627h
Servo
Ramp head command rejected
628h
Servo
Head position not a valid tracking head position
629h
Servo
Head position not a valid tracking head position for restart
tracking
62Ah
Servo
Attempt to set linear counter mark failed since already past
point.
62Bh
Servo
Tape ready for retension
62Ch
Servo
Expecting moving up with added hysteresis after reference
sensor high.
62Dh
Servo
Invalid command called or invalid message sent to sequencer
62Eh
Servo
Timeout during head stepper stopping after searching for servo
bundle
62Fh
Servo
Timeout during head stepper moving up with added hysteresis
after reference sens
630h
Servo
Expecting searching for servo bundle
631h
Servo
Expecting hysteresis before searching for servo bundle in other
direction
632h
Servo
Expecting searching for servo bundle in other direction
633h
Servo
Expecting stopping after failing search for servo bundle in other
direction
Advertisement
Table of Contents
