Table of Contents
Advertisement
SRV_STEP_THREAD_TAPE_ERROR14
SRV_STEP_THREAD_TAPE_ERROR15
SRV_STEP_THREAD_TAPE_ERROR16
SRV_STEP_THREAD_TAPE_ERROR17
SRV_STEP_THREAD_TAPE_ERROR18
SRV_STEP_THREAD_TAPE_ERROR19
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR5
SRV_STEP_PWR_RECOVERY_LOAD_CART_EXPECT
ED_TRAY_OUT
SRV_STEP_THREAD_TAPE_ERROR22
SRV_STEP_THREAD_TAPE_ERROR23
SRV_STEP_THREAD_TAPE_DEFAULT
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR7
SRV_STEP_UNTHREAD_TAPE_ERROR2
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR8
SRV_STEP_PWR_RECOVERY_LOAD_CART_DEFAUL
T
SRV_STEP_UNTHREAD_TAPE_ERROR6
SRV_STEP_UNTHREAD_TAPE_ERROR7
SRV_STEP_LOAD_CART_ERROR5
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R10
SRV_STEP_UNTHREAD_TAPE_ERROR10
SRV_STEP_UNTHREAD_TAPE_ERROR11
SRV_STEP_UNTHREAD_TAPE_ERROR12
SRV_STEP_UNTHREAD_TAPE_ERROR13
SRV_STEP_UNTHREAD_TAPE_ERROR14
SRV_STEP_UNTHREAD_TAPE_ERROR15
SRV_STEP_UNTHREAD_TAPE_ERROR16
SRV_STEP_UNTHREAD_TAPE_ERROR17
SRV_STEP_UNTHREAD_TAPE_DEFAULT
SRV_STEP_MOTOR_ERROR1
SRV_STEP_STEP_MOTOR_DEFAULT
SRV_STEP_HEAD_INVALID_WRAP
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_MOVIN
G_TO_POSITION
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_ADDE
D_HYSTERESIS
SRV_STEP_HEAD_EXPECTING_TOP_SENSOR_HIGH
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_TOP_S
ENSOR_HIGH
SRV_STEP_HEAD_EXPECTING_TOP_SENSOR_LOW
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_TOP_S
ENSOR_LOW
SRV_STEP_HEAD_STEP_DEFAULT
SRV_STEP_STEP_DEFAULT
SRV_STEP_SETUP_MOTOR_CONTROL_DEFAULT
SRV_STEP_RETRY_THREAD_TAPE_ERROR1
SRV_STEP_RETRY_THREAD_TAPE_ERROR2
SRV_STEP_RETRY_THREAD_TAPE_ERROR3
SRV_STEP_RETRY_THREAD_TAPE_DEFAULT
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R11
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R12
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_DEFA
ULT
SRV_STEP_GOFROM_HUB_TOPARK_ERROR1
275h
Servo
expecting MECH_DELAY2_DONE
276h
Servo
Load arm stalled pulling pin from cartridge
277h
Servo
While removing the hysteresis from the load arm (hooking the
pin) the bi-cell va
278h
Servo
The load arm failed to grab the pin to thread the tape and all of
the retries we
279h
Servo
All retries for pulling tape from the cartridge were used up
27Ah
Servo
expecting SNS7
27Bh
Servo
expecting steps done
27Ch
Servo
expecting SNS2 low
27Dh
Servo
Load arm motor stalled while finishing a thread operation
27Eh
Servo
Cartridge reel motor did not move as much as expected.
27Fh
Servo
An unexpected state occurred in the tape thread task.
280h
Servo
expecting steps done
281h
Servo
motor stall
282h
Servo
expecting eerpom done
283h
Servo
invalid state in srv_dcl_loadCartridgePoweronRecovery function
284h
Servo
Load arm stalled while leaving the hub
285h
Servo
expecting steps done
286h
Servo
expecting serial eeprom done
287h
Servo
expecting SNS13 high
288h
Servo
35motor stall waiting
289h
Servo
expecting steps done
28Ah
Servo
SNS13 Did not change to expected value
28Bh
Servo
expecting steps done
28Ch
Servo
Removing tape slack from the cartridge failed during Unthread
28Dh
Servo
failed to release pin
28Eh
Servo
motor stall waiting for HALT4
28Fh
Servo
Unexpected id
290h
Servo
An unexpected state occurred in the tape unthread task.
291h
Servo
expecting steps done
292h
Servo
An in unexpected state occurred in the move motor task.
293h
Servo
invalid wrap value
294h
Servo
expecting HALT1
295h
Servo
expecting steps done
296h
Servo
expecting SNS9 high
297h
Servo
expecting HALT2
298h
Servo
expecting SNS9 low
299h
Servo
expecting HALT3
29Ah
Servo
An unexpected state occurred in the head step task.
29Bh
Servo
An unexpected state occurred in the step motor task.
29Ch
Servo
An unexpected state occurred in the cartridge load task
29Dh
Servo
expecting HALT1
29Eh
Servo
expecting SNS13 low
29Fh
Servo
expecting steps done
2A0h
Servo
An unexpected state occurred in the cartridge load task.
2A1h
Servo
motor stall waiting for ENGAGED_LEADER
2A2h
Servo
expecting steps done
2A3h
Servo
An unexpected state occurred in the power on recovery task.
2A4h
Servo
expecting steps done
Advertisement
Table of Contents
