Table of Contents
Advertisement
TAPE_DS_IN_OUT_SEQUENCE
TAPE_DS_DN_OUT_SEQUENCE
TAPE_READ_BLANK_TAPE
TAPE_ILLEGAL_SPEED
TAPE_VCO_LOCK_ERR
TAPE_VCO_PHASE_ERR
TAPE_RECYCLING_DATA_SETS
TAPE_CHAN_ILLEGAL_EQ_REG
TAPE_CHAN_ILLEGAL_PA_REG
TAPE_DS_NOT_AVAILABLE
TAPE_UNEXP_SERVO_ALERT
TAPE_CHAN_SET_CALIB_ID_ERROR
TAPE_CHAN_SET_CALIB_MODE_ERROR
TAPE_CHAN_ILLEGAL_MODE
TAPE_SERVO_ERROR
TAPE_CHAN_READ_CALIB_ID_ERROR
TAPE_CHAN_READ_CALIB_MODE_ERROR
TAPE_AUTO_LOAD_FAILED
TAPE_READ_END_OF_WRAP
TAPE_RAW_READ_UNDERRUN
TAPE_CHAN_EQ1_COMM_ERROR
TAPE_CHAN_EQ2_COMM_ERROR
TAPE_CHAN_EQ1_AND_EQ2_COMM_ERROR
TAPE_BAD_MIC_PAGE
TAPE_UNEXP_MSG_REC
TAPE_SRV_RAMP_UP_TO_LP1
TAPE_SRV_RAMP_UP_TO_LP6
TAPE_WRITE_LOOP_BACK_FAIL
TAPE_WRITE_ISB_SVO_FAIL
TAPE_WRITE_DSS_SERVO_FAULT
TAPE_FIRST_DS_SERVO_REC_FAIL
TAPE_UNEXP_SVA_LP1_UNDERRUN
TAPE_UNEXP_SVA_LP6_OVERRUN
TAPE_AUTO_LOAD_CM_FAILED
TAPE_READ_ILLEGAL_OLD_DATA
TAPE_FIRST_DS_APPEND_FAIL
SRV_PARPORT_SCRAMBLER_NOT_READY_IN_PASS
_THRU
SRV_MOVETAPE_REVERSE_PHYSICAL_LIMIT_UNDE
RRUN_DURING_CRUISE_CONTROL
SRV_CMDPROC_SET_TAPE_SPEED_REJ_INVALID_S
TATE
SRV_CMDPROC_SET_TAPE_SPEED_REJ_NOT_INCR
EASING
SRV_MOVETAPE_FORWARD_PHYSICAL_LIMIT_OVE
RRUN_DURING_RAMP_UP
SRV_REJ_INV_STATE
SRV_REJ_CMD
SRV_REJ_PARM
SRV_REJ_FORMAT
SRV_REJ_NO_LP1
SRV_REJ_NO_CARTRIDGE
SRV_REJ_NOT_THREADED
SRV_REJ_AT_BOT
SRV_REJ_REWINDING
SRV_REJ_CLEANING
SRV_LPOS_TABLE_FULL
SRV_UNKNOWN_REASON
SRV_DIVIDER_ERROR
A6h
Tape
Write: Data Set in out of sequence.
A7h
Tape
Write: Data Set done out of sequence.
A8h
Tape
Read: Blank Tape
A9h
Tape
tp_set_vco(): illegal speed.
AAh
Tape
tp_set_vco(): VCO_LOCK error.
ABh
Tape
tp_set_vco(): VCO is not running in correct phase.
ACh
Tape
ADh
Tape
Not a valid equalizer register (>20 during read)
AEh
Tape
Not a valid preamp register (> 53)
AFh
Tape
Data Set not available
B0h
Tape
Write/Read: Unexpected SERVO_ALERT Message is received.
B1h
Tape
B2h
Tape
B3h
Tape
B4h
Tape
Seek: Unrecoverable Hard Servo Error
B5h
Tape
B6h
Tape
B7h
Tape
autoload sequence failure
B8h
Tape
Read: RAW read end-of-wrap
B9h
Tape
Read: RAW underrun error
BAh
Tape
BBh
Tape
BCh
Tape
BDh
Tape
Task: Bad MIC page error
BEh
Tape
Task: Unexpected Message Received
BFh
Tape
Write: Append ramp up
C0h
Tape
Write: Append ramp up
C1h
Tape
Write: WRITE_LOOP_BACK error detected.
C2h
Tape
Write: LOOP_BACK
C3h
Tape
Write: LOOP_BACK
C4h
Tape
Write: Fail to handle the Servo demark
C5h
Tape
Write: unexpected lp1 received.
C6h
Tape
Write: unexpected lp6 received.
C7h
Tape
CM failure during autoload sequence
C8h
Tape
Read: Reader detects old data which has higher WPC than new
data WPC
C9h
Tape
Write: Fail to detect the last
CAh
Servo
Scrambler not ready to accept command for pass thru mode
CBh
Servo
Physical limit exceeded in reverse direction
CCh
Servo
Reject set tape speed command same
CDh
Servo
Reject set tape speed command
CEh
Servo
Physical limit in forward direction exceeded in ramp up state
CFh
Servo
Invalid State For This Command
D0h
Servo
Unrecognized Command
D1h
Servo
Invalid Parameter Received
D2h
Servo
Invalid Message Format
D3h
Servo
LP1 Not Set
D4h
Servo
No cartridge present
D5h
Servo
Cartridge not threaded yet
D6h
Servo
Cmd rejected
D7h
Servo
Cmd rejected
D8h
Servo
Cleaning tape inserted
D9h
Servo
LPOS table is full.
DAh
Servo
Unknown reason code in cmd response memory.
DBh
Servo
Hardware divider detected a division error
Advertisement
Table of Contents
