Quantum LTO 3 User Manual page 247

SCSI_CREATE_SENSE_FAILED
SCSI_INITALIZE_SENSE_FAILED
SCSI_UNKNOWN_CM_EEPROM_STATE
SCSI_INVALID_LOG_PARAMETER
SCSI_INVALID_LOG_PAGE
SCSI_INVALID_LOG_PAGE_CONTROL
SCSI_PAGE_OUT_OF_RANGE
SCSI_UNKNOWN_LOG_INFO_RESPONSE
SCSI_UNKNOWN_LOG_INFO_RESPONSE_DATA_POI
NTER
SRV_CMDPROC_CMD_REJECT_ABORT_IN_PROGRE
SS
SRV_CMDPROC_CMD_REJECT_SEQUENCER_BUSY
SRV_CMDPROC_PARAMETER_OUT_OF_RANGE
SRV_CMDPROC_SETTAPETHICK_API_REJECT_BUSY
SRV_CMDPROC_SETTENSION_API_REJECT_BUSY_I
N_STATUS_REQUEST
SRV_CMDPROC_SETRADIUSCOUNTER_API_REJECT
_BUSY
SRV_CMDPROC_INVALID_COMMAND_IN_SET_PARA
METER
SRV_REEL_AT_SPEED_MESSAGE_RECEIVED_IN_IDL
E_STATE
SRV_REEL_TRACKING_MESSAGE_RECEIVED_IN_IDL
E_STATE
SRV_REEL_AT_SPEED_MESSAGE_RECEIVED_IN_HO
LD_STATE
SRV_REEL_TRACKING_MESSAGE_RECEIVED_IN_HO
LD_STATE
SRV_MOVETAPE_FORWARD_PHYSICAL_LIMIT_OVE
RRUN_DURING_RAMP_DOWN
SRV_MOVETAPE_REVERSE_PHYSICAL_LIMIT_UNDE
RRUN_DURING_RAMP_DOWN
SRV_MOVETAPE_FORWARD_PHYSICAL_LIMIT_OVE
RRUN_DURING_RAMP_DOWN_RESTART
SRV_MOVETAPE_REVERSE_PHYSICAL_LIMIT_UNDE
RRUN_DURING_RAMP_DOWN_RESTART
SRV_SEQ_SUBCOMMAND_TIMED_OUT
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R1
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R2
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R3
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R4
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R5
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R6
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R7
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R8
SRV_STEP_PWR_RECOVERY_THREAD_TAPE_ERRO
R9
SRV_MOVETAPE_RAMP_DOWN_FAILED_IN_RAMP_D
OWN_AT_LPOS_FROM_CRUISE_CONTROL_FORWAR
D
SRV_MOVETAPE_RAMP_DOWN_FAILED_IN_RAMP_D
22Ah SCSI SCSI Task failed to creaate microcode changed sense
22Bh SCSI
22Ch SCSI
22Dh SCSI
22Eh SCSI
22Fh SCSI
230h SCSI Log page out of range
231h SCSI
232h SCSI
233h Servo Abort command rejected since already aborting.
234h Servo Mechanical command rejected
235h Servo Parameter out of range for command.
236h Servo API SetTapeThick failed
237h Servo API SetTension failed
238h Servo API SetRadiusCounter failed
239h Servo Invalid parameter in set parameter function.
23Ah Servo AT_SPEED message received in idle state.
23Bh Servo TRACKING message received in idle state.
23Ch Servo AT_SPEED message received in hold state.
23Dh Servo TRACKING message received in hold state.
23Eh Servo Forward Physical limit exceeded in ramp down state.
23Fh Servo Reverse physical limit exceeded in ramp down state.
240h Servo Forward physical limit exceeded in ramp down restart state.
241h Servo Reverse physical limit exceeded in ramp down restart state.
242h Servo Subcommand timeout in sequencer.
243h Servo The Load Arm was unable to find the Cart Bicell target zone
during Thread Power
244h Servo expecting SNS13 low
245h Servo expecting steps done
246h Servo failed to remove slack
247h Servo failed to release pin
248h Servo The Load Arm failed while moving to home position (in front of
the guides) durin
249h Servo expecting steps done
24Ah Servo exceeded retries
24Bh Servo motor stall waiting for SNS13 high
24Ch Servo Ramp down failed in ramp_down_at_lpos_from_cruise_control
in forward direction.
24Dh Servo Ramp down failed in ramp_down_at_lpos_from_cruise_control