Table of Contents
Advertisement
OUT_DURING_SEARCHING_FOR_PES
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_FOUND_PES
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_FOUND_PES
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVING_UP_WITH_ADDED_HYSTERE
SIS
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_ADDED_HYSTERE
SIS
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_CAPTURING_PES_SAMPLES
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_GOING_TO_NEW_
OFFSET
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVING_UP_WITH_ADDED_HYSTERE
SIS_FOR_VERIFICATION
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_VERIFYING_NEW_OFFSET
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_GOING_TO_OFFSE
T
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_REFERENCE_SEN
SOR_LOW
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_REFERENCE_SEN
SOR_HIGH
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_PES_FOUND
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_DEALING_WITH_HYSTERESIS
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVE_UNTIL_REFERENCE_SENSOR_
LOW
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVE_UNTIL_REFERENCE_SENSOR_
HIGH
SRV_LPOS_NEW_ESTIMATE_JUMPED_MORE_THAN_
2_FROM_PREVIOUS_RELATIVE_LPOS
SRV_CMDPROC_CMD_REJECT_DRIVE_MECH_STUC
K
SRV_CMDPROC_EMERGENCY_EJECT_IN_PROGRES
S_ABORT_NOT_VALID
SRV_SEQ_INVALID_HIGHER_PRIORITY_COMMAND_
RECEIVED
SRV_INVALID_REEL_STATE_FOR_SET_RUN_TENSIO
N_COMMAND
SRV_SEQ_NON_STANDARD_CARTRIDGE_RADIUS
SRV_TIMEOUT_DURING_HEAD_STEPPER_IDLE
SRV_TIMEOUT_DURING_HEAD_STEPPER_STARTING
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_T
O_POSITION
SRV_TIMEOUT_DURING_HEAD_STEPPER_STOPPING
_AFTER_MOVING_TO_POSITION
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_
UP_WITH_ADDED_HYSTERESIS
SRV_TIMEOUT_DURING_HEAD_STEPPER_VALIDATI
NG_PES
pes.
48Dh
Servo
Timeout during head stepper offset calibration found pes.
48Eh
Servo
Timeout during head stepper offset calibration stopping after
found pes.
48Fh
Servo
Timeout during head stepper offset calibration moving up with
added hysteresis.
490h
Servo
Timeout during head stepper offset calibration stopping after
added hysteresis.
491h
Servo
Timeout during head stepper offset calibration capturing pes
samples.
492h
Servo
Timeout during head stepper offset calibration stopping after
going to new offse
493h
Servo
Timeout during head stepper offset calibration moving up with
added hysteresis f
494h
Servo
Timeout during head stepper offset calibration verifying new
offset.
495h
Servo
Timeout during head stepper offset calibration stopping after
going to offset.
496h
Servo
Timeout during head stepper offset calibration stopping after
reference sensor l
497h
Servo
Timeout during head stepper offset calibration stopping after
reference sensor h
498h
Servo
Timeout during head stepper offset calibration stopping after
pes found.
499h
Servo
Timeout during head stepper offset calibration dealing with
hysteresis.
49Ah
Servo
Timeout during head stepper offset calibration move until
reference sensor low.
49Bh
Servo
Timeout during head stepper offset calibration move until
reference sensor high.
49Ch
Servo
New estimated LPOS should never jump more than 2 from
previous relative_lpos.
49Dh
Servo
Drive requires recovery command to 'unstuck' mechanics
49Eh
Servo
Abort rejected because emergency eject was in progress
49Fh
Servo
A higher priority command was received from the command
processor that was not a
4A0h
Servo
Invalid reel state for set run tension command.
4A1h
Servo
Calculated radius does not match possible radii for cartridges
4A2h
Servo
Timeout during head stepper idle.
4A3h
Servo
Timeout during head stepper starting.
4A4h
Servo
Timeout during head stepper moving to position.
4A5h
Servo
Timeout during head stepper stopping after moving to position.
4A6h
Servo
Timeout during head stepper moving up with added hysteresis.
4A7h
Servo
Timeout during head stepper validating pes.
Advertisement
Table of Contents
