Mitsubishi Electric 800 Series Instruction Manual page 524

Object Object name
identifier
25 Cumulative power
52 PID set point
54 PID deviation
67 PID measured value 2
92 Second PID set point
94 Second PID deviation
95 Second PID measured
value 2
200 Alarm history 1
201 Alarm history 2
202 Alarm history 3
203 Alarm history 4
300
*2
Speed scale
310
PID set point CMD
311 PID measured value
*2
CMD
312
PID deviation CMD
320 Second PID set point
CMD
321 Second PID measured
value CMD
322 Second PID deviation
CMD
398 Mailbox parameter
399 Mailbox value
10007 Acceleration time
10008 Deceleration time
*1 R: Read only, W: Read/Write (Commandable values not supported), C: Read/Write (Commandable values supported)
Values written to the objects that support the commandable values are stored in the Priority Array, even when "Write Access Denied" is returned
due to inconsistency of the writing requirements such as the operating mode, on condition that the values are written within the setting range.
*2 If communication speed command source is other than NET, the setting value can be written, but not to be applied.
*3 When both Pr.1136 and Pr.1138 ≠ "9999", the setting range is from the smaller coefficient to the larger coefficient of Pr.1136 and Pr.1138.
Depending on the setting, the writing value and the reading value may not be the same at the minimum digit.
Present value
*1
access type
R Represents the cumulative power monitor.
R Represents the PID set point monitor.
R Represents the PID deviation monitor.
(Minus display is available with reference to 0%, in 0.1%
increment.)
R Represents the PID measured value 2 monitor.
R Represents the second PID set point monitor.
R Represents the second PID deviation monitor.
(Minus display is available with reference to 0%, in 0.1%
increment.)
R Represents the second PID measured value 2 monitor.
R Represents the fault history 1 (the latest fault) monitor.
R Represents the fault history 2 (second fault in past) monitor.
R Represents the fault history 3 (third fault in past) monitor.
R Represents the fault history 4 (fourth fault in past) monitor.
C Controls the ratio of the frequency command. (Setting range:
0.00 to 100.00)
(Refer to
C Set the PID action set point.
*2
This object is the set point during PID operation if Pr.128 =
"60 or 61". (Setting range: 0.00 to 100.00)
C Set the PID measured value.
This object is the measured value during PID operation if
Pr.128 = "60 or 61". (Setting range: 0.00 to 100.00)
C Set the PID deviation. (0.01 increment)
*2
This object is the deviation during PID operation if Pr.128 =
"50 or 51". (Setting range: -100.00 to 100.00)
C Set the second PID action set point.
This object is the set point during PID operation if Pr.753 =
"60 or 61". (Setting range: 0.00 to 100.00)
C Set the second PID measured value.
This object is the measured value during PID operation if
Pr.753 = "60 or 61". (Setting range: 0.00 to 100.00)
C Set the second PID deviation. (0.01 increment)
This object is the deviation during PID operation if Pr.753 =
"50 or 51". (Setting range: -100.00 to 100.00)
W Access to the properties which are not defined as objects are
available. (Refer to
W
W Set Pr.7 Acceleration time.
W Set Pr.8 Deceleration time.
Description
page 518.)
page 526.)
5.12 (N) Operation via communication and its settings
Unit
kilowatt-
hours
(19)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
no-units
(95)
percent
(98)
no-units
(95)
*3
no-units
(95)
*3
percent
(98)
no-units
(95)
*3
no-units
(95)
*3
percent
(98)
no-units
(95)
no-units
(95)
seconds
(73)
seconds
(73)
5. PARAMETERS
3
4
5
5
5
6
7
8
9
10
523