Mitsubishi Electric 800 Series Instruction Manual page 302

Setting Signal
name
Positive Negative
logic logic
211 311 LUP
212 312 LDN
213 313 Y213
215 315 Y215
217 317 Y217
218 318 STIR
219 319 Y219
220 320 Y220
226 326 Y226
228 328 DRY
229 329 Y229
230 330 Y230
247 347 LSYN
248 348 Y248
249 349 Y249
250 350 Y250
9999 ―
*1 Take caution when changing the frequency setting with an analog signal, because this change speed and the timing of the change speed
determined by the acceleration/deceleration time setting may cause the output of the SU (up to frequency) signal to switch repeatedly between
ON and OFF. (This repeating does not occur when the acceleration/deceleration time setting is "0 s".)
*2 The setting is available only for standard models.
*3 This signal cannot be assigned to the output terminals for plug-in options (FR-A8AY, FR-A8AR).
*4 Available when the plug-in option is connected.
*5 This signal is available when the PLC function is enabled, or when an option (FR-A8AY, FR-A8AR, FR-A8NC, or FR-A8NCE) is installed. For the
corresponding parameters of each option, refer to the Instruction Manual of the option.
*6 When the power is reset, the fault output 2 signal (ALM2) turns OFF at the same time as the power turns OFF.
NOTE
• The same function may be set to more than one terminal
• The terminal conducts during function operation when the setting is "0 to 99, 200 to 299", and does not conduct when the
setting is "100 to 199, 300 to 399".
• When Pr.76 Fault code output selection = "1", the output signals of terminals SU, IPF, OL and FU operate according to
Pr.76 setting. (When the inverter's protective function is activated, the signal output switches to fault code output.)
• The outputs of terminal RUN and the fault output relay are assigned according to the settings above, regardless of Pr.76.
• Changing the terminal assignment using Pr.190 to Pr.196 (Output terminal function selection) may affect the other
functions. Set parameters after confirming the function of each terminal.
• Do not assign signals which repeat frequently between ON and OFF to terminals A1B1C1 or A2B2C2. The life of the relay
contacts will be shortened.
Function
Upper limit warning Output when the load fault upper limit warning is
detection detected.
Lower limit warning Output when the load fault lower limit warning is
detection detected.
During load characteristics Output during measurement of the load
measurement characteristics.
During cleaning Output during operation of the cleaning
function.
Priming pump operation Outputs the signal for starting the priming pump. Pr.1363
Stirring Output during the stirring operation.
PID upper/lower limit pre- Output when the PID measured value meets the
warning requirements of the limit pre-warning signal
output conditions.
Second PID upper/lower
limit pre-warning
Auxiliary pressure pump Output when the PID deviation exceeds the
operation auxiliary pressure pump operation starting level.
Dry run Output when a dry-run state is detected.
PID input pressure warning Output when the pump inlet pressure reaches
the warning level.
PID input pressure fault Output when the pump inlet pressure reaches
the fault level.
Phase synchronization Output when phase synchronization for
*4 bypass switching has completed (for FR-
completion
A8AVP).
Estimated residual-life of Output when the main circuit capacitor
main circuit capacitor (for approaches the end of its estimated life.
*2*5
Pr.313 to Pr.322)
ABC1 relay contact life (for Output when the relay contacts of terminals A1,
B1, and C1 approach the end of their life.
*5
Pr.313 to Pr.322)
ABC2 relay contact life (for Output when the relay contacts of terminals A2,
*5 B2, and C2 approach the end of their life.
Pr.313 to Pr.322)
No function ―
Operation
Pr.1480 to
Pr.1492
Pr.1469 to
Pr.1479
Pr.1364, Pr.1365
Pr.1346, Pr.1370
to Pr.1373
Pr.1374, Pr.1375
Pr.42, Pr.43,
Pr.132, Pr.1144,
Pr.1370
Pr.1370,
Pr.1373,
Pr.1377,
Pr.1378, Pr.1380
Pr.1370,
Pr.1377,
Pr.1379, Pr.1381
Pr.139
Pr.255, Pr.506
Pr.255, Pr.507
Pr.255, Pr.508
―
5.8 (M) Monitor display and monitor output signal
Related Refer
parameter to
3
page
265
4
5
391
440
5
5
6
7
8
―
182
9
10
―
301
5. PARAMETERS