Mitsubishi Electric 800 Series Instruction Manual page 143

 G: Control Parameter
Parameters for motor control.
Pr. Pr.
group
G000 0
Torque boost
G001 3
Base frequency
G002 19 Base frequency voltage
G003 14 Load pattern selection
G010 46 Second torque boost
G011 47 Second V/F (base frequency)
G030 60 Energy saving control selection
G040 100 V/F1 (first frequency)
G041 101 V/F1 (first frequency voltage)
G042 102 V/F2 (second frequency)
G043 103 V/F2 (second frequency voltage)
G044 104 V/F3 (third frequency)
G045 105 V/F3 (third frequency voltage)
G046 106 V/F4 (fourth frequency)
G047 107 V/F4 (fourth frequency voltage)
G048 108 V/F5 (fifth frequency)
G049 109 V/F5 (fifth frequency voltage)
G080 617 Reverse rotation excitation current
low-speed scaling factor
G100 10 DC injection brake operation
frequency
G101 11 DC injection brake operation time
G105 522 Output stop frequency
G106 250 Stop selection
G107 70 Parameter for manufacturer setting. Do not
set.
G110 12 DC injection brake operation
voltage
G120 882 Regeneration avoidance operation
selection
G121 883 Regeneration avoidance operation
level
G122 884 Regeneration avoidance at
deceleration detection sensitivity
G123 885 Regeneration avoidance
compensation frequency limit
value
G124 886 Regeneration avoidance voltage
gain
G125 665 Regeneration avoidance frequency
gain
G130 660 Increased magnetic excitation
deceleration operation selection
G131 661 Magnetic excitation increase rate
G132 662 Increased magnetic excitation
current level
G200 800 Control method selection
G201 85 Excitation current break point
G202 86 Excitation current low-speed
scaling factor
G203 245 Rated slip
G204 246 Slip compensation time constant
G205 247 Constant-power range slip
compensation selection
G211 820 Speed control P gain 1
G212 821 Speed control integral time 1
142
5. PARAMETERS
5.1 Parameter List
Name Refer
to
page
538
Simple Simple Simple
539
Simple Simple Simple
539
541
538
539
543
544
544
544
544
544
544
544
544
544
544
542
546
546
548
550
546
559
559
559
559
559
559
562
562
562
145
542
542
563
563
563
155
155
Pr. Pr.
group
G213 824 Torque control P gain 1 (current
loop proportional gain)
G214 825 Torque control integral time 1
(current loop integral time)
G216 827 Torque detection filter 1
G224 828 Parameter for manufacturer setting. Do not
set.
G301 565 Second motor excitation current
break point
G302 566 Second motor excitation current
low-speed scaling factor
G311 830 Speed control P gain 2
G312 831 Speed control integral time 2
G313 834 Torque control P gain 2 (current
loop proportional gain)
G314 835 Torque control integral time 2
(current loop integral time)
G316 837 Torque detection filter 2
G410 653 Speed smoothing control
G411 654 Speed smoothing cutoff frequency
G932 89 Speed control gain (Advanced
magnetic flux vector)
G942 569 Second motor speed control gain
*1 Setting can be made only for the standard model.
*2 The setting is available when the PLC function is enabled.
Name Refer
to
page
155
155
158
542
542
155
155
155
155
158
564
564
149
149