Table of Contents
Advertisement
No.
25
Q: How to detect controller Fault?
26
Q: New ISaGRAF retained variable is better than old one.
27
Q: How to link to Modbus ASCII Slave device?
Q: How to use multi-port Modbus Master in the WinCon-8037/8337/8737 &
28
WinCon-8036/8336/8736?
Q: How to send/receive message from ISaGRAF PAC to remote PCs or Controllers via
29
Ethernet UDP communication?
Q: Setting special "range" parameter of temperature input board to get clear "Degree
30
Celsius" or "Degree Fahrenheit" input value. For ex, "1535" means 15.35 degree.
Q: Setting a special "ADR_" parameter of remote I-7000 & I-87K temperature input module
31
to get clear "Degree Celsius" or "Degree Fahrenheit" input value. For ex, "8754" means
87.54 degree.
Q: How to access to ISaGRAF variables as array? (A demo program of sending string to
32
COM2 or COM3 when alarm 1 to 8 happens)
33
Q: Setting up more Modbus RTU Slave ports in WinCon ISaGRAF PACs.
34
Q: Compiling error result in different ISaGRAF version?
Q: Slow down ISaGRAF driver speed to work better with InduSoft software in
35
W-8036/8336/8736 & W-8046/8346/8746?
36
Q: Redundancy Solution in WinCon-8xx7.
37
Q: I-7188EG/XG support remotely downloads via Modem Link.
38
Q: Setting I-7188EG/XG's COM3 as Modbus RTU Slave port.
39
Q: ISaGRAF version 3.4 & 3.5 now supporting "Variable Array" !!!
40
Q: Setting I-8437/I-8837/I-8437-80/I-8837-80's COM3 as Modbus RTU Slave port.
41
Q: How to connect PC / HMI to a Redundancy system with a single IP address?
Q: How to use WinCon connecting to Ethernet I/O? The I/O scan rate is about 30 to 40 msec
42
for 3000 to 6000 I/O channels.
Q: How to setup WinCon-8xx7 as TCP/IP Client to communicate to PC or other TCP/IP Server
43
device? Or WinCon automatically report data to PC via TCP/IP?
44
Q: WinCon-8xx7/8xx6 automatically report data to PC/InduSoft or PC/HMI?
45
Q: ISaGRAF controllers display message to EKAN Modview LED.
46
Q: How to Write 16-bits to Modbus RTU devices by Mobus function call No. 6?
47
Q: How to Read or Write Floating Point value to Modbus RTU Slave device?
48
Q: How to use WinCon-8xx7 / 8xx6 to control FRnet I/O?
Q: Setting a special "CODE_" parameter of "MBUS_R" & "MBUS_R1" to get a clear "Degree
49
Celsius" or "Degree Fahrenheit" input value of M-7000 temperature module. For ex,
"3012" means 30.12 degree.
50
Q: How to connect an ISaGRAF controller to M-7000 Remote I/O?
51
Q: VB.net 2005 Demo program using Modbus TCP/IP protocol to control ISaGRAF PACs
52
Q: VB 6.0 Demo program using Modbus TCP/IP protocol to control ISaGRAF PACs.
53
Q: Performance Comparison Table of ISaGRAF PACs.
9-12
English ISaGRAF Ver.3 FAQ
ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
Advertisement
Table of Contents
