Emerson Rosemount 700XA Reference Manual page 283

1
NOTES:
THIS PROCEDURE TO BE PERFORMED IN A CLEAN AND DRY AREA.
ALL PARTS TO BE BLOWN CLEAN AND DRY WITH NITROGEN
D
BEFORE ASSEMBLY.
6
LOWER
11
ACTUATOR
DIAPHRAGM
3X 7
C
5
UPPER
11
ACTUATOR
DIAPHRAGM
3X 8
4
CUSHION
11
DIAPHRAGM
SEALING
11
B
DIAPHRAGM
1
3
9
10
A
PART NO. 2-3-0710-100
1
2
6 PORT XA VALVE ASSEMBLY INSTRUCTIONS:
1. Assembly is to be accomplished by building the valve in the upside down position using production fixture.
2. Inspect the primary plate, Item 3 , to insure that the tubing ports are clean and that the sealing surface
has no scratches or pits. Then place it in the fixture with the sealing surface facing up.
3. Insert .125 Dia. guide pin, Item 2 , and .093 Dia. guide pin, Item 1 , in the locating holes in the plate.
4. Place the amber sealing diaphragm ( has no holes in the actuating plane) over the guide pins and align.
5. Place the white cushion diaphragm (has same hole pattern as sealing diaphragm in step 4) over the
sealing diaphragm and align.
6. Place the upper piston plate, Item 4 , over the guide pins with the piston recess holes facing up.
7. Load 3 each of the short pistons, Item 8 , into the recess holes of the plate.
8. Place two amber upper actuator diaphragms ( has 3 large holes for long pistons to feed through) over the
guide pins and align.
9. Place the lower piston plate, Item 5 , over the guide pins with the piston recess holes facing up.
10. Load 3 each of the long pistons, Item 7 , into the recess holes of the plate.
11. Place two amber lower actuator diaphragms over the guide pins and align.
12. Place base plate, item 6 over the guide pins and align.
13. Place washer, Item 9 , over bolt, Item 10 , and insert the bolt from the bottom up through the valve
assembly, tighten bolt Item 10 to 20 Ft. LBS. Remove from fixture and Install into Unit.
1 11
1 10
1 9
3 8
3 7
1 6
1 5
1 4
1 3
1 2
1 1
G01 ITEM
QTY NO.
METRIC
GEOMETRIC TOLERANCES &
DIMENSIONS PER ASME Y14.5
LATEST REVISION.
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS ARE IN mm [in].
TOLERANCES ARE:
X. ± 1.0 mm [.040 in]
X.X ± .25 mm [.010 in]
X.XX ± .10 mm [.004 in]
FINISH:
ANGULAR ± .5°
N/A
BREAK ALL SHARP CORNERS TO
MATERIAL:
.10-.40 mm [.004-.016 in] RADIUS
SEE BOM
AND REMOVE ALL BURRS
2
3
REVISION HISTORY
REV DESCRIPTION
C ECO-XX-5004955
D ECO-XX-5005171
E ECO-5008234
9A00096G01 KIT, DIAPHRAGM, 6-PORT XA
2-4-9216-060 HEX HEAD BOLT, 1/4-28 X 1.375, ALLOY ZINC-YELLOW
2-4-1518-047 WASHER FLAT, 1/4 BOLT SIZE, 18-8 SST
2-4-0710-247 SHORT PISTON 6 & 10 PORT XA VALVES 700XA GC
2-4-0710-246 LONG PISTON 6 & 10 PORT XA VALVES 700XA GC
2-4-0710-235 BASE MINI 6 PORT VALVE, ROUND 700 XA GC
2-4-0710-234 LOWER PISTON PLATE MINI 6 PORT, ROUND 700 XA GC
2-4-0710-233 UPPER PISTON PLATE WITH BOSS 6 PORT XA VALVE
2-4-0710-232 PRIMARY PLATE WITHOUT BOSS MINI 6 PORT XA VALVE
2-4-0710-170 GUIDE PIN, Ø .125, 18-8 SST
2-4-0710-169 GUIDE PIN, Ø .093, 18-8 SST
PART
DESCRIPTION
NUMBER
TITLE
ASSEMBLY, 6-PORT VALVE, XA
DRN DATE
JCB
SIZE DWG NO.
4/16/2009
B
CHKD DATE
HVB
4/16/2009
SCALE
ENG DATE
HVB/NP
4/16/2009
3
4
DRAWN CHECKED APPROVED DATE
NP
EM
HM 8/2/2009
CC NP
EM 10/25/2009
N. MAHOOT S. BLACK C. REINA 1/4/2022
UNITS
CONFIDENTIAL AND PROPRIETARY INFORMATION IS
CONTAINED HERE IN AND MUST BE HANDLED ACCORDINGLY.
ROSEMOUNT INC.
CE22260
SHT
1 OF 1
1:1
4
D
C
EA
EA
EA
EA
EA B
EA
EA
EA
EA
EA
EA
A
REV
E