MacDon M105 Assembly Instructions Manual page 38

C x x x || A C T I V A T E
L1
M x x x ||
L2
Form 169558
UNLOADING AND ASSEMBLY
C x x x || S E N S O R
L1
M x x x || H D R
L2 H E I G H T
C x x x || S E N S O R
L1
M x x x || H E A D E R
L2
C x x x || S E N S O R
L1
M x x x || K N I F E
L2
C x x x || S E N S O R
L1
M x x x || R E E L
L2
F U N C T I O N S ?
N O / Y E S
C x x x || A C T I V A T E
L1
M x x x || H E A D E R
L2
C x x x || A C T I V A T E
L1
M x x x ||
L2 R E E L
C x x x || A C T I V A T E
L1
M x x x || H D R
L2 T I L T
C x x x || A C T I V A T E
L1
M x x x || K N I F E
L2
C x x x || A C T I V A T E
L1
M x x x || D R A P E R / A U G E R
L2
C x x x || A C T I V A T E
L1
M x x x || R E E L
L2
C x x x || A C T I V A T E
L1
M x x x ||
L2
C x x x || T O
L1 A C T I V A T E
M x x x || P R E S S
L2
C x x x || P U R G E
L1
M x x x || P R E S S
L2
C x x x || P U R G E
L1
M x x x ||
L2
C x x x || P U R G E
L1
M x x x ||
L2 N O
C x x x || E X I T
L1
M x x x ||
L2
C x x x || E X I T
L1
M x x x ||
L2
I N P U T
S E N S O R
I N P U T
A N G L E S E N S O R
I N P U T
S P E E D S E N S O R
I N P U T
S P E E D S E N S O R
E X I T
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
I N / O U T
F U N C T I O N S ?
D R I V E O N
F U N C T I O N S ?
O N
F U N C T I O N S ?
F O R E / A F T
H Y D P U R G E ?
N O / Y E S
P U R G E
A N D H O L D
C Y C L E S T A R T E D
A N D H O L D
C Y C L E E N D E D
C Y C L E E N D E D
E X I T Y E S
F U N C T I O N M E N U ?
N O / Y E S
D I A G N O S T I C S ?
N O / Y E S
36
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading would
have been.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
If "NO" then jump to:
D I A G N O S T I C S ?
For diagnostic purposes each header function can
be activated by using the "arrow" keys on the CDM.
When "SELECT" is pressed the program will go to
the next function that can be activated.
If the HEADER TILT cylinder or the REEL FORE /
AFT valve is not installed under the TRACTOR
SETUP menu then the ACTIVATE FUNCTIONS
menu selection for these items should be
suppressed.
ACTIVATE HYD PURGE - This is to allow the
operator to purge the air from a new or changed
pump system.
Pressing and holding the right hand "arrow" button
activates a predetermined timed purge cycle.
Releasing pressure on the switch or a completed
cycle (timed out) will jump to the PURGE CYCLE
ENDED menu selection.
If "NO" then jump to:
H E A D E R D O W N / U P
If "NO" then jump to:
D I A G N O S T I C M O D E ?
Revision A