MacDon M105 Assembly Instructions Manual page 35

C x x x || S E T
L1
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
C x x x || V I E W
L1
M x x x ||
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
L2
L1
L2
C x x x || E X I T
L1
M x x x ||
L2
||
L1 C x x x C A B D I S P L A Y
||
L2 M x x x
C x x x || D I S P L A Y
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
C x x x || D I S P L A Y
L1
M x x x ||
L2
M x x x ||
L2
Form 169558
UNLOADING AND ASSEMBLY
C O N T R O L L O C K S ?
N O / Y E S
C x x x || D R A P E R
M x x x ||
E N A B L E D / L O C K E D
C x x x || A U G E R
S P E E D
M x x x ||
E N A B L E D / L O C K E D
C x x x || R E E L
S P E E D
M x x x ||
E N A B L E D / L O C K E D
C x x x || R E E L
F O R E / A F T
M x x x ||
E N A B L E D / L O C K E D
C x x x || H E A D E R
M x x x ||
E N A B L E D / L O C K E D
C x x x || E X I T
C O N T R O L
M x x x ||
N O / Y E S
C O N T R O L
N O / Y E S
C x x x || D R A P E R
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || A U G E R
S P E E D
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || R E E L
S P E E D
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || R E E L
F O R E / A F T
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || H E A D E R
M x x x ||
5 7 5 . 1
M x x x ||
6 4 8 . 6
C x x x || E X I T
V I E W
M x x x ||
N O / Y E S
T R A C T O R
N O / Y E S
S E T U P ?
N O / Y E S
L A N G U A G E ?
E N G L I S H
E S P A N O L
R U S S I A N
U N I T S ?
I M P E R I A L
M E T R I C
V I E W
S P E E D
T I L T
L O C K S ?
L O C K S ?
E X I T
S P E E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
H R S E N A B L E D
H R S L O C K E D
T I L T
H R S E N A B L E D
H R S L O C K E D
L O C K O U T S ?
S E T U P ?
T I L T
If "NO" then jump to:
C A L I B R A T E
Use the "arrow" keys to change the default
language. Pressing "SELECT" goes to the next L1
The "arrow" keys are used to select between
IMPERIAL or METRIC. The default value will be
33
If "NO" then jump to:
C O N T R O L L O C K S ?
This menu allows the operator to selectably "lock
out" the control functions for the various header
functions. The default or selected "status" for each
item will flash.
If the expansion module is not installed the
corresponding menu items should be suppressed.
The "arrow" keys are used to ENABLE or LOCK
OUT each function. Pressing "SELECT" will go to
the next L1 menu item.
Tilt to be suppressed if not "installed" in the tractor
setup menu.
If "NO" then jump to:
D R A P E R S P E E D
E N A B L E D / L O C K E D
If "NO" then jump to:
T R A C T O R S E T U P ?
When the control lock outs are viewed, the lower
display line (L2) will show the engine hours and
either ENABLED or LOCKED to indicate the
present status along with the engine hours at which
time the function was either ENABLED or LOCKED.
Using the "arrow" keys allows the operator to select
the various functions. Pressing "SELECT" will go to
the EXIT VIEW LOCKOUTS? menu selection.
If any of the HDR ANGLE / KNIFE SPEED or REEL
SPEED sensors are not "installed" (no expansion
module or A30 Auger header selected, they should
be suppressed.
If "NO" then jump to:
D R A P E R S P E E D
If "NO" then jump to:
C Y L I N S T A L L E D ?
S E N S O R S ?
menu selection.
displayed first.
(continued next page)
Revision A