MacDon M105 Assembly Instructions Manual page 36

C x x x || C D M
L1
M x x x ||
L2
C x x x || C D M
L1
M x x x ||
L2
C x x x || C D M
L1
M x x x ||
L2
C x x x || E X I T
L1
M x x x ||
L2
||
L1 C x x x C A L I B R A T E
||
L2 M x x x
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
C x x x || H E I G H T
L1
M x x x || R A I S E
L2
C x x x || C A L I B R A T I N G
L1
M x x x || R A I S E
L2
M x x x || R A I S E
L2
C x x x || H E I G H T
L1
M x x x || P R E S S
L2
M x x x || C A L I B R A T I N G
L1
M x x x || L O W E R
L2
M x x x || H T
L2
C x x x || T O
L1
M x x x ||
L2
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
M x x x || H D R
L1
M x x x || E X T E N D
L2
C x x x || C A L I B R A T I N G
L1
M x x x || E X T E N D
L2
M x x x || E X T E N D
L2
M x x x || H D R
L1
M x x x || P R E S S
L2
C x x x || C A L I B R A T I N G
L1
M x x x || R E T R A C T
L2
M x x x || H D R
L2
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
C x x x || E X I T
L1
M x x x ||
L2
Form 169558
UNLOADING AND ASSEMBLY
B U Z Z E R V O L U M E
▂ ▂ ▃ ▅ ▆ ▇
B A C K L I G H T I N G
▂ ▂ ▃ ▅ ▆ ▇
C O N T R A S T
▂ ▂ ▃ ▅ ▆ ▇
D I S P L A Y
N O / Y E S
S E N S O R S ?
N O / Y E S
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
S T O P & E X I T
S E N S O R
H D R T O
H E I G H T
H E A D E R
H E A D E R
S E N S O R
L O W E R H E A D E R
H E I G H T
H E A D E R
S E N S O R C O M P L E T E
C A L I B R A T E
H E A D E R H E I G H T
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
T I L T S E N S O R
T L T T O
T I L T
T I L T
T I L T
T I L T S E N S O R
R E T R A C T
T I L T
T I L T
T I L T C O M P L E T E
C A L I B R A T E
H E A D E R T I L T
S T O P & E X I T
C A L I B R A T I O N ?
N O / Y E S
The "arrow" keys are used to change the CDM
buzzer volume, CDM backlighting or the CDM
contrast, with the bar graph indicating the relative
level for each item. When "SELECT" is pressed
the program goes to the EXIT DISPLAY SETUP?
S E T U P ?
D I S P L A Y
If "NO" then jump to:
D I A G N O S T I C
S E L E C T
The operator can select any of the two items
requiring calibration or to STOP & EXIT the menu.
When a function is activated, the display will
indicate the function being calibrated. HOLD will
C A L
flash until the system has completed reading in the
S T A R T
signal with the header fully raised.
DONE will flash and prompt the operator to
H O L D
COMPLETE the sensor calibration by lowering the
D O N E
C A L
H O L D
S E L E C T
The menu will display the last item selected when
the calibration routine is completed.
S E L E C T
C A L
S T A R T
If the HEADER TILT option in the TRACTOR
H O L D
SETUP is set to NO then only HEIGHT should be
D O N E
available as a menu selection for calibration.
C A L
T I L T
H O L D
S E L E C T
T O C A L I B R A T E
34
menu selection.
If "NO" then jump to:
L A N G U A G E ?
M O D E ?
header.
If "NO" then jump to:
S E L E C T
(continued next page)
Revision A