Page 2 Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
Page 3: Table Of Contents
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Table of Contents Table of Contents ................................i Introduction ................................1 Audience ................................. 1 Other Documentation .............................. 1 Conventions ................................1 Notes, Notices, and Cautions ..........................1 Web-based Switch Configuration ........................3 Management Options .............................
Page 4 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide SNMP Linkchange Trap Settings ........................37 SNMP View Table Settings ..........................38 SNMP Community Table Settings ........................38 SNMP Group Table Settings ........................... 39 SNMP Engine ID Local Settings ........................40 SNMP User Table Settings ..........................
Page 5 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Asymmetric VLAN ............................108 MAC VLAN ..............................109 VLAN Interface .............................. 109 Super VLAN ..............................115 Auto Surveillance VLAN ..........................116 Voice VLAN ..............................119 Private VLAN ..............................122 VLAN Tunnel ..............................
Page 6 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Null Interface ..............................194 UDP Helper ................................. 194 IP Forward Protocol ............................194 IP Helper Address ............................195 IPv4 Static/Default Route ............................ 195 IPv4 Route Table ..............................196 IPv6 Static/Default Route ............................ 197 IPv6 Route Table ..............................
Page 7 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Access Control List (ACL) ..........................269 ACL Configuration Wizard ..........................269 Step 1 - Create/Update ..........................269 Step 2 - Select Packet Type .......................... 270 Step 3 - Add Rule ............................270 Step 4 - Apply Port ............................
Page 8 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide BPDU Attack Protection ............................348 MAC Authentication ............................349 Web-based Access Control ..........................351 Web Authentication ............................353 WAC Port Settings ............................353 WAC Customize Page ........................... 354 Network Access Authentication .......................... 355 Guest VLAN ..............................
Page 9 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide DDM TX Power Threshold Settings ......................402 DDM RX Power Threshold Settings ......................402 DDM Status Table ............................403 Monitoring ................................. 404 VLAN Counter ..............................404 Utilization ................................405 Port Utilization ...............................
Page 10 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide CFM Extension ..............................440 Configuration/Firmware ............................441 DAD ..................................443 DDM ..................................444 DHCPv6 Client ..............................444 DHCPv6 Server ..............................446 Dynamic ARP Inspection ............................ 446 ERPS .................................. 446 Ethernet OAM ..............................
Page 11 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Port ..................................469 RMON ................................. 469 Safeguard ................................469 SIM ..................................470 Stacking ................................471 Start ..................................471 Storm Control ..............................471 System File ................................. 472 Upload/Download ............................... 472 VRRP ..................................
Page 12: Introduction
Switch by using the Web User Interface (Web UI). The Web UI is the secondary management interface to the DGS-3130 Series Switch, which will be generally be referred to simply as the “Switch” within this manual. This manual is written in a way that assumes that you already have the experience and knowledge of Ethernet and modern networking principles for Local Area Networks.
Page 13 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide CAUTION: A caution indicates a potential for property damage, personal injury, or death.
Page 14: Web-Based Switch Configuration
Switch. Alternatively, the Switch can also be managed, in-band, by using a Telnet connection to any of the LAN ports on the Switch. The command line interface provides complete access to all Switch management features. For more detailed information about the CLI, refer to the DGS-3130 Series CLI Reference Guide. SNMP-based Management The Switch can be managed with an SNMP-compatible Network Management System (NMS).
Page 15: Web User Interface (Web Ui)
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 2-1 Displays entering the IP address in Internet Explorer After pressing the ENTER key, the following authentication window should appear, as shown below. Figure 2-2 Web UI Login Window When connecting to the Web UI of the Switch for the first time, leave the User Name and Password fields blank and click Login since there are no login user accounts created by default on the Switch.
Page 16 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide AREA 1 AREA 2 AREA 3 AREA 4 Figure 2-3 Main Web UI Window Area Number Description AREA 1 This area displays a graphical, near real-time image of the front panel of the Switch.
Page 17: System
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide System Device Information System Information Settings Peripheral Settings Port Configuration System Log Time and SNTP Time Range Device Information In the Device Information section, the user can view a list of basic information regarding the Switch. It appears automatically when you log on to the Switch.
Page 18: Peripheral Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-2 System Information Settings Window The fields that can be configured in System Information Settings are described below: Parameter Description System Name Enter a system name for the Switch, if so desired. This name will identify it in the Switch network.
Page 19: Port Configuration
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-3 Peripheral Settings Window The fields that can be configured in Environment Trap Settings are described below: Parameter Description Fan Trap Select to enable or disable the fan trap state for waning fan event (fan failed or fan recover).
Page 20 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click System > Port Configuration > Port Settings, as shown below: Figure 3-4 Port Settings Window The fields that can be configured are described below:...
Page 21: Port Status
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Speed Select the port speed option here. This option will manually force the connection speed on the selected port to only connect at the speed specified here.
Page 22: Port Gbic
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-5 Port Status Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be displayed here.
Page 23: Error Disable Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-7 Port Auto Negotiation Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be displayed here.
Page 24: Jumbo Frame
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured for Error Disable Trap Settings are described below: Parameter Description Asserted Specifies to enable or disable notifications for entering into the error disabled state.
Page 25: Interface Description
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-9 Jumbo Frame Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be configured here.
Page 26: Poe
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The DGS-3130-30PS and DGS-3130-54PS switches support Power over Ethernet (PoE) as defined by the IEEE 802.3af and 802.3at. All ports can support PoE up to 30W. The Switch ports can supply about 48 VDC power to Powered Devices (PDs) over Category 5 or Category 3 UTP Ethernet cables.
Page 27: Poe Status
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Usage Threshold Enter the usage threshold to generate a log and send the corresponding standard notification. The range is from 1 to 99 percent. Policy Preempt Select this option to enable or disable the disconnection of the Powered Device...
Page 28: Poe Configuration
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-123 PoE Status Window The fields that can be configured for PoE Status are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be configured here.
Page 29: Pd Alive
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Priority Select the priority for provisioning power to the port. Options to choose from are Critical, High and Low. Legacy Support Select this option to enable or disable the support of legacy PD.
Page 30: Poe Statistics
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description PD Alive State Select to enable or disable the state of the PoE alive function on the specified port(s) here. PD IP Address Enter the IPv4 address of the target PD here.
Page 31: Poe Measurement
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide PoE Measurement This window is used to display the PoE measurement information on the Switch ports. To view the following window, click System > PoE > PoE Measurement, as shown below:...
Page 32 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-178 System Log Settings Window The fields that can be configured for Log State are described below: Parameter Description Log State Select the enable or disable the global system log state here.
Page 33: System Log Discriminator Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Severity Select the severity value of the type of information that will be logged. Options to choose from are 0 (Emergencies), 1 (Alerts), 2 (Critical), 3 (Errors), 4 (Warnings), 5 (Notifications), 6 (Informational), and 7 (Debugging).
Page 34: System Log Server Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-189 System Log Discriminator Settings Window The fields that can be configured are described below: Parameter Description Discriminator Name Enter the name of the discriminator profile here. This name can be up to 15 characters long.
Page 35 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-20 System Log Server Settings Window The fields that can be configured are described below: Parameter Description Host IPv4 Address Enter the system log server IPv4 address here.
Page 36: System Log
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description local2 Local use 2 (local2) local3 Local use 3 (local3) local4 Local use 4 (local4) local5 Local use 5 (local5) local6 Local use 6 (local6) local7 Local use 7 (local7)
Page 37: Time And Sntp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 3-22 System Attack Log Window The fields that can be configured are described below: Parameter Description Unit Select the stacking unit ID of the Switch that will be displayed here.
Page 38 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click System > Time and SNTP > Time Zone Settings, as shown below: Figure 3-24 Time Zone Settings Window The fields that can be configured are described below:...
Page 39: Sntp Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description From: Time Select the time of the day that summer time will start. To: Week of the Month Select week of the month that summer time will end.
Page 40: Time Range
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in SNTP Global Settings are described below: Parameter Description SNTP State Select this option to enable or disable SNTP. Poll Interval Enter the synchronizing interval in seconds. The value is from 30 to 99999 seconds.
Page 41 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Delete Periodic button to delete the periodic entry. Click the Delete button to delete the specified entry.
Page 42: Management
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Management Command Logging User Accounts Settings Password Encryption Password Recovery Login Method SNMP RMON Telnet/Web Session Timeout DHCP DHCP Auto Configuration IP Source Interface File System Stacking SMTP Settings Command Logging This window is used to display and configure the command logging function.
Page 43: Password Encryption
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After selecting the User Management Settings tab, the following page will appear. Figure 4-2 User Accounts Settings Window The fields that can be configured are described below: Parameter Description User Name Enter the user account name here.
Page 44: Password Recovery
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > Password Encryption, as shown below: Figure 4-4 Password Encryption Window The fields that can be configured are described below: Parameter Description...
Page 45 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > Login Method, as shown below: Figure 4-6 Login Method Window The fields that can be configured in Enable Password are described below:...
Page 46: Snmp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Login Password are described below: Parameter Description Application Select the application that will be configured here. Options to choose from are Console, Telnet and SSH.
Page 47: Snmp Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide A Management Information Base (MIB) stores management and counter information. The Switch uses the standard MIB-II Management Information Base module, and so values for MIB objects can be retrieved using any SNMP-based network management software.
Page 48: Snmp Linkchange Trap Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Trap Settings are described below: Parameter Description Trap Global State Select this option to enable or disable the sending of all or specific SNMP notifications.
Page 49: Snmp View Table Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide SNMP View Table Settings This window is used to assign views to community strings that define which MIB objects can be accessed by a remote SNMP manager. The SNMP sub-tree OID created with this table maps SNMP users to the views created in the SNMP User Table Settings window.
Page 50: Snmp Group Table Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide • Any MIB view that defines the subset of MIB objects that will be accessible to the SNMP community. • Read-write or read-only level permissions for the MIB objects accessible to the SNMP community.
Page 51: Snmp Engine Id Local Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SNMP > SNMP Group Table Settings, as shown below: Figure 4-11 SNMP Group Table Settings Window The fields that can be configured are described below:...
Page 52: Snmp User Table Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SNMP > SNMP Engine ID Local Settings, as shown below: Figure 4-12 SNMP Engine ID Local Settings Window The fields that can be configured are described below:...
Page 53: Snmp Host Table Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Auth-Protocol by Password When selecting v3 in the SNMP Version drop-down list, and selecting Password in the SNMP V3 Encryption drop-down list, this option is available. Select the authentication level. Options to choose from are the following: •...
Page 54 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SNMP > SNMP Host Table Settings, as shown below: Figure 4-14 SNMP Host Table Settings Window The fields that can be configured are described below:...
Page 55: Rmon
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide RMON RMON Global Settings This window is used to enable or disable remote monitoring (RMON) for the rising and falling alarm trap feature for the SNMP function on the Switch.
Page 56: Rmon History Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Show Detail button, the following window will appear.
Page 57: Rmon Alarm Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following window will appear. Figure 4-19 RMON History Settings (Show Detail) Window Click the Back button to return to the previous window.
Page 58: Rmon Event Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide RMON Event Settings This window is used to display and configure event entries. To view the following window, click Management > RMON > RMON Event Settings, as shown below:...
Page 59: Telnet/Web
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Telnet/Web This window is used to display and configure Telnet and Web settings on the Switch. To view the following window, click Management > Telnet/Web, as shown below: Figure 4-23 Telnet/Web Window...
Page 60: Session Timeout
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Session Timeout This window is used to display and configure the session timeout settings. To view the following window, click Management > Session Timeout, as shown below: Figure 4-24 Session Timeout Window...
Page 61: Dhcp Class Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Service DHCP are described below: Parameter Description Service DHCP State Select this option to enable or disable the DHCP Relay service. Click the Apply button to accept the changes made.
Page 62: Dhcp Server
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 4-27 DHCP Class Settings (Edit) Window The fields that can be configured are described below: Parameter Description Option Enter the DHCP option number. The range is from 1 to 255.
Page 63 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Server > DHCP Server Global Settings, as shown below: Figure 4-28 DHCP Server Global Settings Window The fields that can be configured in DHCP Use Class State are described below:...
Page 64 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Pool Name Enter the DHCP server pool name here. This name can be up to 32 characters long.
Page 65 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit Option button, the following page will appear. Figure 4-31 DHCP Server Pool Settings (Edit Option) Window The fields that can be configured are described below:...
Page 66 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Network (IP/Mask) Enter the network IPv4 address and subnet mask for the DHCP client here. Next Server Enter the next server IPv4 address here. The boot image file is stored on this server and can be retrieved by DHCP clients using this IP address.
Page 67 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Begin Address Enter the first IPv4 address of a range of addresses to be excluded here. End Address Enter the last IPv4 address of a range of addresses to be excluded here.
Page 68 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 4-35 DHCP Server Manual Binding Window The fields that can be configured are described below: Parameter Description Pool Name Enter the DHCP server pool name here. This name can be up to 32 characters long.
Page 69 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Address Enter the binding entry IPv4 address here. Pool Name Enter the DHCP server pool name here. This name can be up to 32 characters long.
Page 70: Dhcpv6 Server
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Server > DHCP Server Statistic, as shown below: Figure 4-388 DHCP Server Statistic Window Click the Clear button to clear the statistics information displayed here.
Page 71 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Configure button to configure the DHCPv6 server pool settings. Click the Delete button to remove the specified entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 72 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Valid Lifetime Enter the valid lifetime value here. The valid lifetime should be greater than the preferred lifetime. The range is from 60 to 4294967295 seconds. By default, this value is 2592000 seconds (30 days).
Page 73 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IPv6 Address Enter the binding entry IPv6 address to be displayed or cleared here. Select the All option to display or clear all DHCPv6 client prefix bindings in or from the binding table.
Page 74: Dhcp Relay
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCPv6 Server > DHCPv6 Server Operational Information, as shown below: Figure 4-434 DHCPv6 Server Operational Information Window DHCP Relay DHCP Relay Global Settings This window is used to display and configure the global DHCP relay settings.
Page 75 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Edit button to modify the corresponding information of the specific DHCP pool. Click the Delete button to remove the specified entry.
Page 76 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit button under Class, the following window will appear. Figure 4-489 DHCP Relay Pool Settings (Class Edit) Window The fields that can be configured are described below:...
Page 77 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Information Settings, as shown below: Figure 4-491 DHCP Relay Information Settings Window The fields that can be configured are described below:...
Page 78 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Information Option Format Settings, as shown below: Figure 4-502 DHCP Relay Information Option Format Settings Window...
Page 79 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide DHCP Relay Information Profile Settings This window is used to display and configure the DHCP relay information profile settings. To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Information Profile...
Page 80 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Port Settings, as shown below: Figure 4-524 DHCP Relay Port Settings Window The fields that can be configured are described below:...
Page 81: Dhcpv6 Relay
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide DHCPv6 Relay DHCPv6 Relay Global Settings This window is used to display and configure the DHCPv6 Relay remote ID settings. To view the following window, click Management > DHCP > DHCPv6 Relay > DHCPv6 Relay Global Settings, as...
Page 82 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in DHCPv6 Relay Interface ID Settings are described below: Parameter Description IPv6 DHCP Relay Interface Select the IPv6 DHCP relay interface ID format that will be used here. Options ID Format to choose from are Default, CID, Vendor1, and Expert UDF.
Page 83 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DHCP > DHCPv6 Relay > DHCPv6 Relay Interface Settings, as shown below: Figure 4-557 DHCPv6 Relay Interface Settings Window The fields that can be configured are described below:...
Page 84 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the range of ports that will be used for this configuration here.
Page 85: Dhcp Auto Configuration
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide function. If disabled, the local relay function will always add Option 37 to request packets, whether the state of Option 37 is enabled or disabled. The DHCPv6 local relay function will directly forward the packet from the server to the client.
Page 86: Dns Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide often supplied by a DHCP or BOOTP server, or can be entered manually and configured into the operating system at startup. DNS Global Settings This window is used to display and configure the global DNS settings.
Page 87: Dns Host Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > DNS > DNS Name Server Settings, as shown below: Figure 4-583 DNS Name Server Settings Window The fields that can be configured are described below:...
Page 88: File System
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > IP Source Interface, as shown below: Figure 4-605 IP Source Interface Window The fields that can be configured in IP TFTP Source Interface are described below:...
Page 89 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the hyperlink, the following window will appear: Figure 4-627 File System (Drive) Window Click the Go button to navigate to the path entered. Click the Previous button to return to the previous window.
Page 90: Stacking
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description selecting the Source File option can the source file path and filename be entered in the space provided. Destination Select the destination Switch Unit ID and type of destination file that will be copied here.
Page 91 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 4-69 Duplex Ring stacking topology (SFP+) NOTE: For more stacking topologies, please refer to Switch Stacking section in DGS-3130-Series HW Installation Guide. Switch Roles in a Stack Within each of these topologies, each Switch plays a role in the Switch stack. These roles can be set by the user per individual Switch, or if desired, can be automatically determined by the Switch stack.
Page 92 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide and then will assign that Switch as the Primary Master if all priorities are the same. The Primary master is physically displayed by the seven segment LED to the far right on the front panel of the Switch where the LED will flash between its given Box ID and ‘H’.
Page 93: Physical Stacking
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide dynamically learned databases, such as ARP, will also be cleared. The new Primary Master will inherit the MAC and IP address of the previous Primary Master to avoid conflict within the stack and the network itself.
Page 94: Stacking Bandwidth
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Stack ID are described below: Parameter Description Current Unit ID Select the unit ID of the Switch in the stack. New Box ID Select the new box ID for the Switch that is selected in the Current Unit ID field.
Page 95: Virtual Stacking (Sim)
Click the Apply button to accept the changes made. Virtual Stacking (SIM) D-Link Single IP Management (SIM) is a concept that will stack Switches together over Ethernet instead of using stacking ports or modules. There are some advantages in implementing the Single IP Management feature: •...
Page 96: Single Ip Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide • Each device begins in a CaS state. • A CS must change its role to CaS and then to MS, to become a MS of a SIM group. Thus, the CS cannot directly be converted to a MS.
Page 97: Topology
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in SIM Role Configure are described below: Parameter Description Role State Select to change the SIM role of the Switch. Options to choose from are Candidate, and Commander.
Page 98 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > Virtual Stacking (SIM) > Topology, as shown below: Figure 4-73 Topology Window There is a menu bar at the top of the window containing File, Group, Device, View, and Help.
Page 99 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Interval Enter the SIM topology display refresh interval value here. The range is from 10 to 300. Show All Select this option to display all available SIM devices in the topology.
Page 100 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Topology Under View, select Topology to view the following: Figure 4-76 View > Topology Click the Zoom In button enlarge the size of the displayed items. Click the Zoom Out button reduce the size of the displayed items.
Page 101 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Tool Tips In the Topology view window, the mouse plays an important role in configuration and in viewing device information. Hover the mouse pointer over a specific device in the Topology window to display more information about the device Figure 4-77 Device Information Utilizing the Tool Tip Hover the mouse pointer over a line between two devices to display the connection speed between the two devices.
Page 102 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 4-79 Group Property Figure 4-80 Commander Switch Property Figure 4-82 Candidate Switch Property Figure 4-81 Member Switch Property The fields displayed are described below: Parameter Description Name Displays the Device Name of the Switches in the SIM group configured. If the device is not configured with a name, it will be given the name default and tagged with the last six digits of the MAC address to identify it.
Page 103: D-Link Discovery Protocol
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide D-Link Discovery Protocol This window is used to display and configure the D-Link Discovery Protocol (DDP) settings. To view the following window, click Management > D-Link Discovery Protocol, as shown below:...
Page 104 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SMTP Settings, as shown below: Figure 4-85 SMTP Settings Window The fields that can be configured in SMTP Global Settings are described below:...
Page 105: Pppoe Circuit Id Insertion Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Send a Test Mail to All are described below: Parameter Description Subject Enter the subject of the email here. This string can be up to 128 characters long.
Page 106: Reboot Schedule Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Reboot Schedule Settings This window is used to display and configure the reboot schedule settings. Use this window to configure the reboot schedule of the Switch. The reboot schedule must take effect within 30 days. After the reboot schedule has taken effect and the Switch is restarted, it will generate a log message to identify that the Switch has been restarted using the reboot schedule.
Page 107: Sd Card Execute Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SD Card Management > SD Card Backup Settings, as shown below: Figure 4-88 SD Card Backup Settings Window The fields that can be configured are described below:...
Page 108 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Management > SD Card Management > SD Card Execute Settings, as shown below: Figure 4-659 SD Card Execute Settings Window The fields that can be configured in Execute Configuration are described below:...
Page 109: Layer 2 Features
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Layer 2 Features VLAN VLAN Tunnel ERPS (G.8032) Loopback Detection Link Aggregation L2 Protocol Tunnel L2 Multicast Control LLDP Static FDB Unicast Static FDB This window is used to display and configure the static unicast forwarding settings on the Switch.
Page 110: Mac Address Table Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Multicast Static FDB This window is used to display and configure the multicast static FDB settings. To view the following window, click L2 Features > FDB > Static FDB > Multicast Static FDB, as shown below:...
Page 111 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. After selecting the MAC Address Port Learning Settings tab option, at the top of the page, the following page will be available.
Page 112: Mac Address Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description VID List Enter the VLAN ID(s) that will be used in this configuration or display here. A series of VLAN IDs can be entered separated by commas or a range of VLAN IDs can be entered separated by a hyphen.
Page 113: Mac Notification
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Clear All button to clear all dynamic MAC addresses. Click the Show All button to display all the MAC addresses recorded in the MAC address table.
Page 114: Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made for each individual section. After selecting the MAC Notification History tab, at the top of the page, the following page will be available.
Page 115: 802.1V Protocol Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. 802.1v Protocol VLAN Protocol VLAN Profile This window is used to display and configure 802.1v protocol VLAN profiles.
Page 116: Gvrp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > 802.1v Protocol VLAN > Protocol VLAN Profile Interface, as shown below: Figure 5-11 Protocol VLAN Profile Interface Window...
Page 117 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description GVRP address or 802.1ad service provider GVRP address. Options to choose from are Dot1d and Dot1ad. Click the Apply button to accept the changes made. GVRP Port This window is used to display and configure the GVRP port settings.
Page 118 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > GVRP > GVRP Advertise VLAN, as shown below: Figure 5-14 GVRP Advertise VLAN Window The fields that can be configured are described below:...
Page 119: Asymmetric Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the range of ports that will be used for this configuration here.
Page 120: Mac Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-17 Asymmetric VLAN Window The fields that can be configured are described below: Parameter Description Asymmetric VLAN State Select to enable or disable the asymmetric VLAN feature here.
Page 121 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > VLAN Interface, as shown below: Figure 5-19 VLAN Interface Window The fields that can be configured are described below:...
Page 122 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After click the Edit button, the following page will appear. This is a dynamic page that will change when a different VLAN Mode is selected. When Access was selected as the VLAN Mode, the following page will appear.
Page 123 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description VLAN Mode Select the VLAN mode option here. Options to choose from are Access, Hybrid, Trunk, 802.1Q-Tunnel, Promiscuous, Host, Trunk Promiscuous, and Trunk Secondary.
Page 124 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description After ticking the Native VLAN option the following parameter will be available. Enter the VLAN ID used for this configuration here. This value must be between 1 and 4094.
Page 125 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide When Promiscuous was selected as the VLAN Mode, the following page will appear. Figure 5-25 VLAN Interface (Promiscuous) Window The fields that can be configured are described below: Parameter...
Page 126: Super Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Back button to discard the changes made and return to the previous page. Super VLAN This window is used to display and configure the super VLAN settings. This is used to specify a VLAN as a super VLAN.
Page 127: Auto Surveillance Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Delete button to remove the specific entry or to remove the sub-VLAN from the super VLAN. Click the IP Range List link to add an IP range to the sub-VLAN.
Page 128 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > Auto Surveillance VLAN > Auto Surveillance Properties, as shown below: Figure 5-29 Auto Surveillance Properties Window The fields that can be configured in Global Settings are described below:...
Page 129 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description source MAC addresses of the packets comply with the Organizationally Unique Identifier (OUI) addresses. Click the Apply button to accept the changes made. MAC Settings and Surveillance Device This window is used to display and configure surveillance devices and their MAC settings.
Page 130: Voice Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After selecting the Auto Surveillance VLAN Summary tab option, at the top of the page, the following page will be available. Figure 5-31 MAC Settings and Surveillance Device (Auto Surveillance VLAN Summary) Window...
Page 131 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description timer will be started. The port will be removed from the voice VLAN after the expiration of the voice VLAN aging timer. If voice traffic resumes during the aging time, the aging timer will be cancelled.
Page 132 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Switch will change its priority. When the voice device sends untagged packets, it will forward them in the voice VLAN. When the Switch receives LLDP-MED packets, it checks the VLAN ID, tagged flag, and priority flag.
Page 133: Private Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > Voice VLAN > Voice VLAN Device, as shown below: Figure 5-35 Voice VLAN Device Window The fields that can be configured are described below:...
Page 134 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > VLAN > Private VLAN, as shown below: Figure 5-37 Private VLAN Window The fields that can be configured for Private VLAN are described below:...
Page 135: Vlan Tunnel
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Secondary VID Enter the secondary private VLAN ID here. When ticking the Remove Association option, specifies that this configuration will not be enabled. Click the Apply button to accept the changes made.
Page 136 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Inner TPID Enter the inner TPID value here. This value is in the hexadecimal form. The range is from 0x1 to 0xFFFF. The inner TPID is used to decide if the ingress packet is C-tagged.
Page 137: Vlan Mapping
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide VLAN Mapping This window is used to display and configure the VLAN mapping settings. If a profile is applied on an interface, the Switch matches the incoming packets according to the rules of the profile. If the packet matches a rule, the action of the rule will be taken.
Page 138: Vlan Mapping Profile
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide VLAN Mapping Profile This window is used to display and configure the VLAN mapping profile settings. To view the following window, click L2 Features > VLAN Tunnel > VLAN Mapping Profile, after clicking Profile ID 1, the rules of Profile 1 will appear.
Page 139 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Add Rule button next to an Ethernet type profile, the following page will appear. Figure 5-42 VLAN Mapping Profile (Ethernet, Add Rule) Window The fields that can be configured are described below:...
Page 140 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Add Rule button next to an IP type profile, the following page will appear. Figure 5-43 VLAN Mapping Profile (IP, Add Rule) Window The fields that can be configured are described below:...
Page 141 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Add Rule button next to an IPv6 type profile, the following page will appear. Figure 5-44 VLAN Mapping Profile (IPv6, Add Rule) Window The fields that can be configured are described below:...
Page 142 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Add Rule button next to an Ethernet-IP type profile, the following page will appear. Figure 5-45 VLAN Mapping Profile (Ethernet-IP, Add Rule) Window The fields that can be configured are described below:...
Page 143: Stp
However, as IEEE 802.1D-2004 RSTP and IEEE 802.1Q-2005 MSTP have been recently introduced to D-Link managed Ethernet Switches, a brief introduction to the technology is provided below followed by a description of how to set up IEEE 802.1D-1998 STP, IEEE 802.1D-2004 RSTP, and IEEE 802.1Q-2005 MSTP.
Page 144 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The Switch implements three versions of the Spanning Tree Protocol, the Multiple Spanning Tree Protocol (MSTP) as defined by IEEE 802.1Q-2005, the Rapid Spanning Tree Protocol (RSTP) as defined by IEEE 802.1D-2004 and a version compatible with IEEE 802.1D-1998.
Page 145: Stp Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide • On the Switch level, the settings are globally implemented. • On the port level, the settings are implemented on a user-defined group of ports. STP Global Settings This window is used to display and configure the global STP settings.
Page 146 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured for STP Priority are described below: Parameter Description Priority Select the STP priority value here. This value is between 0 and 61440. By default, this value is 32768.
Page 147: Stp Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-47 MPT Instance Settings Window The fields that can be configured for MPT Instance are described below: Parameter Description Bridge Name Enter the MPT instance name here. Bridge Priority Select the instance priority here.
Page 148 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > STP > STP Port Settings, as shown below: Figure 5-488 STP Port Settings Window The fields that can be configured are described below:...
Page 149: Mst Configuration Identification
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description delay. If the interface receives a BPDU later, its operation state changes to the non-port-fast state. By default, this option is Network. TCN Filter Select to enable or disable the TCN Filter option. When a port is set to the TCN filter mode, the TC event received by the port will be ignored.
Page 150 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > STP > MST Configuration Identification, as shown below: Figure 5-499 MST Configuration Identification Window The fields that can be configured for MST Configuration Identification are described below:...
Page 151: Stp Instance
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide STP Instance This window is used to display and configure the STP instance settings. To view the following window, click L2 Features > STP > STP Instance, as shown below:...
Page 152: Erps (G.8032)
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Priority After clicking the Edit button, select the priority value here. Options to choose from are 0 to 240. By default this option is 0. A lower value has higher priority.
Page 153 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description If Ethernet ring nodes running ITU-T G.8032v1 and ITU-T G.8032v2 co-exist on an Ethernet ring, the following configurations should be made on the G.8032v2 device: • All physical ring IDs must have the default value of 1.
Page 154 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Port1 Select the checkbox and then select the Switch unit ID and the port number that will be the second ring port of the physical ring. Select the None option, from the drop-down menu, specifies that the inter-connected node is a local node endpoint of an open ring.
Page 155 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Edit Instance button to configure the ERP instance. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 156: Erps Profile
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description RPL Port Select the checkbox and then select the RPL port option here. Options to choose from are Port0 and Port1. The option selected will be configured as the RPL port.
Page 157: Loopback Detection
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Edit button to modify the specified G.8032 profile. Click the Delete button to disassociate the G.8032 profile. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 158 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > Loopback Detection, as shown below: Figure 5-589 Loopback Detection Window The fields that can be configured in Loopback Detection Global Settings are described below:...
Page 159: Link Aggregation
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The Switch supports up to 32 port trunk groups with up to 8 ports in each group.
Page 160 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide This window is used to display and configure the link aggregation settings. To view the following window, click L2 Features > Link Aggregation, as shown below: Figure 5-591 Link Aggregation Window...
Page 161: L2 Protocol Tunnel
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will be available. Figure 5-602 Link Aggregation (Show Detail) Window The fields that can be configured are described below: Parameter...
Page 162 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > L2 Protocol Tunnel, as shown below: Figure 5-613 L2 Protocol Tunnel (L2 Protocol Tunnel Global Setting) Window The fields that can be configured are described below:...
Page 163: L2 Multicast Control
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After selecting the L2 Protocol Tunnel Port Setting tab option, at the top of the page, the following page will be available. Figure 5-624 L2 Protocol Tunnel (L2 Protocol Tunnel Port Setting) Window...
Page 164 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings, as shown below: Figure 5-635 IGMP Snooping Settings Window The fields that can be configured in Global Settings are described below:...
Page 165 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following window will appear. Figure 5-646 IGMP Snooping Settings (Show Detail) Window The window displays the detail information about IGMP snooping VLAN.
Page 166 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Minimum Version Select the minimum IGMP host version that is allowed on the VLAN. Options to choose from are 1, 2, and 3.
Page 167 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in IGMP Snooping AAA Settings are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 168 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description From Port - To Port Select the appropriate port range used for the configuration here. Click the radio button and enter a VLAN ID of the multicast group. The range is from 1 to 4094.
Page 169 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Forbidden Port - Select to have the configured ports not to be multicast router ports. Unit Select the Switch unit that will be used for this configuration here.
Page 170: Mld Snooping
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in IGMP Snooping Statistics Table are described below: Parameter Description Find Type Select the interface type. Options to choose from are VLAN, and Port.
Page 171 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide MLD Snooping Settings This window is used to display and configure the MLD snooping settings. To view the following window, click L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping...
Page 172 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following window will appear. Figure 5-693 MLD Snooping Settings (Show Detail) Window The window displays the detail information about MLD snooping VLAN.
Page 173 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Minimum Version Select the minimum version of MLD hosts that is allowed on the VLAN. Options to choose from are 1 and 2.
Page 174 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Groups Settings, as shown below: Figure 5-715 MLD Snooping Groups Settings Window...
Page 175 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide MLD Snooping Filter Settings This window is used to display and configure the MLD snooping settings. To view the following window, click L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Filter...
Page 176 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in MLD Snooping Limit Settings are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 177 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Please Select button, the following page will appear. Figure 5-72 MLD Snooping Filter Settings (Please Select) Window Select the ACL and click the OK button to use the selected access list.
Page 178 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in MLD Snooping Mrouter Settings are described below: Parameter Description Enter a VLAN ID between 1 and 4094. Configuration Select the port configuration. Options to choose from are Port, Forbidden Port, and Learn pimv6.
Page 179: Multicast Vlan
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Enter a VLAN ID between 1 and 4094. This is available when VLAN is selected in the Statistics drop-down list. Unit Select the Switch unit that will be used for this configuration here. This is available when Port is selected in the Statistics drop-down list.
Page 180 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-81 Multicast VLAN Settings Window The fields that can be configured in Multicast VLAN Global Settings are described below: Parameter Description Multicast VLAN IPv4 State Select to enable or disable the IPv4 IGMP control packet process in multicast VLANs.
Page 181 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Select Delete to delete an entry based in the information entered. Role Select the role here. Options to choose from are Receiver and Source. • Receiver - Specifies to configure the port as a subscriber port that can only receive multicast data in the multicast VLAN.
Page 182 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Multicast VLAN Group Settings This widow is used to view and configure the multicast VLAN group settings. To view the following window, click L2 Features > L2 Multicast Control > Multicast VLAN > Multicast VLAN Group...
Page 183: Multicast Filtering
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Enter the multicast VLAN ID that will be used here. The range is 2 to 4094. Profile Name Enter the group profile name for the multicast VLAN feature here. This name can be up to 32 characters long.
Page 184: Lldp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Multicast Filter Mode Select the multicast filter mode here. Options to choose from are Forward Unregistered, Forward All, and Filter Unregistered. • When selecting the Forward Unregistered option, registered multicast packets will be forwarded based on the forwarding table and all unregistered multicast packets will be flooded based on the VLAN domain.
Page 185: Lldp Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in LLDP Global Settings are described below: Parameter Description LLDP State Select this option to enable or disable the LLDP feature LLDP Forward State Select this option to enable or disable LLDP forward state.
Page 186: Lldp Management Address List
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-745 LLDP Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 187: Lldp Basic Tlvs Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-756 LLDP Management Address List Window The fields that can be configured are described below: Parameter Description Subtype Select the subtype. Options to choose from are All, IPv4 and IPv6. After selecting the IPv4 option, enter the IPv4 address in the space provided.
Page 188: Lldp Dot1 Tlvs Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. LLDP Dot1 TLVs Settings The LLDP Dot1 TLVs Settings page is used to enable or disable outbound LLDP advertisements for IEEE 802.1 organizationally unique port VLAN ID TLVs.
Page 189: Lldp-Med Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-789 LLDP Dot3 TLVs Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 190: Lldp Statistics Information
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-90 LLDP-MED Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 191: Lldp Local Port Information
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-91 LLDP Statistics Information Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used here. Port Select the port number that will be used here.
Page 192 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 5-92 LLDP Local Port Information Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be displayed. Port Select the port number that will be displayed.
Page 193: Lldp Neighbor Port Information
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail hyperlink, a new section will appear at the bottom of the window. Figure 5-94 LLDP Local Port Information (Show Detail) Window Click the Back button to return to the previous window.
Page 194: Layer 3 Features
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Layer 3 Features Gratuitous ARP IPv6 Neighbor Interface UDP Helper IPv4 Static/Default Route IPv4 Route Table IPv6 Static/Default Route IPv6 Route Table Route Preference ECMP Settings RIPng IP Route Filter...
Page 195: Static Arp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-2 ARP Aging Time Window The fields that can be configured are described below: Parameter Description Timeout After click the Edit button, enter the ARP aging timeout value here.
Page 196: Arp Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-4 Proxy ARP Window The fields that can be configured are described below: Parameter Description Proxy ARP State Select to enable or disable the Proxy ARP state here.
Page 197: Gratuitous Arp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. Gratuitous ARP This window is used to display and configure the gratuitous ARP settings. A gratuitous ARP request packet is an ARP request packet where the source and the destination IP address are both set to the IP address of the sending device and the destination MAC address is the broadcast address.
Page 198: Ipv6 Neighbor
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide IPv6 Neighbor This window is used to display and configure the IPv6 neighbor settings. To view the following window, click L3 Features > IPv6 Neighbor, as shown below: Figure 6-7 IPv6 Neighbor Window...
Page 199 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Interface VLAN Enter the interface VLAN ID here. This value must be between 1 and 4094. Click the Apply button to accept the changes made. Click the Find button to locate a specific entry based on the information entered.
Page 200: Ipv6 Interface
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Secondary Tick this option to use the IPv4 address and mask as the secondary interface configuration. Click the Back button to return to the previous window. Click the Apply button to accept the changes made.
Page 201 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-21 IPv6 Interface Window The fields that can be configured in IPv6 Interface are described below: Parameter Description Interface VLAN Enter the VLAN interface ID that will be associated with the IPv6 entry.
Page 202 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description State Select to enable or disable the automatic configuration of the IPv6 address using stateless auto-configuration here. Select the Default option to specify that if the default router is selected on this interface, a default route will be installed using that default router.
Page 203: Loopback Interface
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-43 IPv6 Interface (Detail, Interface IPv6 Address) Window Click the Delete button to delete the specified entry. After selecting the Neighbor Discover tab option, at the top of the page, the following page will be available.
Page 204 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-76 Loopback Interface Window The fields that can be configured are described below: Parameter Description Interface Loopback Enter the loopback interface ID here. The range is from 1 to 8.
Page 205: Null Interface
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Delete button to delete the specified entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 206: Ip Helper Address
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Forward Protocol UDP Enter the destination port of the UDP service to be forwarded here. The range Port is from 1 to 65535.
Page 207: Ipv4 Route Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The Switch also supports a floating static route, which means that the user may create an alternative static route with a different next hop. This secondary next hop device route is considered as a backup static route when the primary static route is down.
Page 208: Ipv6 Static/Default Route
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Address Select and enter the single IPv4 address here. Network Address Select and enter the IPv4 network address here. In the first space enter the network prefix and in the second space enter the network mask.
Page 209: Ipv6 Route Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 210: Ecmp Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-155 Route Preference Window The fields that can be configured are described below: Parameter Description Distance Default Enter the administrative distance of default routes here. The range is from 1 to 255.
Page 211: Rip
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description ECMP Advance Control Select the ECMP advance control mode settings here. This specifies the Mode Setting number of ECMP or multipath routes and the number of next-hops of each ECMP or multipath route that will be changed according to the specified value.
Page 212: Rip Distribute List
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description refers to routes that are established automatically through configuring an IP address on an interface. • Third, enter the value to be used as the metric for the redistributed route here.
Page 213: Rip Interface Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-188 RIP Distribute List Window The fields that can be configured are described below: Parameter Description ACL Name Enter the access list name that will be used here. This name can be up to 32 characters long.
Page 214: Rip Database
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Delete button to delete an entry based on the information entered. Click the Edit button to configure the specific entry. After clicking the Edit button, the following page will appear.
Page 215: Ripng
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Show All button to display all the entries. RIPng RIPng Settings This window is used to display and configure the Routing Information Protocol Next Generation (RIPng) settings, also known as IPv6 RIP.
Page 216: Ripng Interface Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Select the Default option to use the default value here which is 30 seconds. Invalid Time Enter the invalidate timer value in seconds here. The range is from 1 to 65535 seconds.
Page 217: Ripng Database
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Metric Offset Enter the value to be added to the metric of an IPv6 RIP route received on the configured interface here. The range is from 1 to 16. The metric refers to the hop count.
Page 218 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > OSPF > OSPFv2 > OSPFv2 Process Settings, as shown below: Figure 6-35 OSPFv2 Process Settings Window Click the Edit button to modify the specified entry.
Page 219 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 6-37 OSPFv2 Process Settings (Show Detail) Window The fields that can be configured are described below: Parameter...
Page 220 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description ACL Name Enter the access list name that will be used here. This name can be up to 32 characters long.
Page 221 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > OSPF > OSPFv2 > OSPFv2 Passive Interface Settings, as shown below: Figure 6-40 OSPFv2 Passive Interface Settings Window The fields that can be configured are described below:...
Page 222 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description NSSA Select this option to assign the OSPF area as a Not-So-Stubby Area (NSSA) area. Stub Select this option to specify an OSPF area as a Stub Area.
Page 223 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > OSPF > OSPFv2 > OSPFv2 Interface Settings, as shown below: Figure 6-43 OSPFv2 Interface Settings Window The fields that can be configured in OSPF Interface Settings are described below:...
Page 224 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 6-44 OSPFv2 Interface Settings (Show Detail) Window The fields that can be configured are described below: Parameter...
Page 225 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Descriptionx become the DR, the router with the higher router priority will be elected the DR. If the routers have the same priority, the router with the higher router ID takes precedence.
Page 226 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide If no metric value is specified by the default metric, routes redistributed from other protocols will get a metric value of To view the following window, click L3 Features > OSPF > OSPFv2 > OSPFv2 Redistribute Settings, as shown...
Page 227 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > OSPF > OSPFv2 > OSPFv2 Virtual Link Settings, as shown below: Figure 6-46 OSPFv2 Virtual Link Settings Window The fields that can be configured in OSPF Virtual Link are described below:...
Page 228 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Area ID link (0.0.0.1), the following page will appear. Figure 6-47 OSPFv2 Virtual Link Settings (Area ID) Window Click the Back button to return to the previous window.
Page 229 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Link State ID - Specifies to display information associated with the link- state ID. Enter the link state ID in the space provided here. • Self Originate - Specifies to display LSAs generated by the local router.
Page 230 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Interface Name Enter the name of the interface that will be used in the results here. Neighbor Enter the neighbor ID here.
Page 231: Ospfv3
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Host IP Enter the host IPv4 address here. Cost Enter the cost value for the stub entry here. The range is from 1 to 65535. Select the Default option to use the default value, which is 1.
Page 232 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description metrics don't convert directly, using a default metric provides a reasonable substitute and enables the redistribution to proceed. Type Select the distance type here. Options to choose from are Intra-Area, Inter- Area, External-1 and External-2.
Page 233 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > OSPF > OSPFv3 > OSPFv3 Passive Interface Settings, as shown below: Figure 6-56 OSPFv3 Passive Interface Settings Window The fields that can be configured are described below:...
Page 234 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description NSSA Select this option to assign the OSPF area as a Not-So-Stubby Area (NSSA) area. Stub Select this option to define an area as a Stub area.
Page 235 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking a Normal area the Area ID link (0.0.0.0) in the table, the following page will appear. Figure 6-59 OSPFv3 Area Settings (Area ID, Normal) Window Click the OK button to close the window and return to the previous window.
Page 236 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in OSPF Interface Table are described below: Parameter Description Interface Name Enter the name of the interface here. Click the Find button to locate a specific entry based on the information entered.
Page 237 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description two routers attempt to become the DR, the router with the higher router priority becomes the DR. If the router priority is the same for two routers, the router with the higher router ID takes precedence.
Page 238 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Metric Enter the metric value here. This value is used when redistributing other processes to an IPv6 OSPF process. The range is from 1 to 16777214. The default metric is value 20 when no metric value is specified.
Page 239 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Area ID link (0.0.0.1) to access the specified OSPFv3 process. Click the Delete button to delete the specified entry.
Page 240 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description LSDB Type Select the LSDB display type here. Options to choose from are All, Router, Network, Prefix, Link, Inter-Area Prefix, Inter-Area Router, External and NSSA External.
Page 241: Ip Multicast Routing Protocol
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide OSPFv3 Neighbor Table This window is used to find and display the OSPFv3 neighbor information. To view the following window, click L3 Features > OSPF > OSPFv3 > OSPFv3 Neighbor Table, as shown below:...
Page 242 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click L3 Features > IP Multicast Routing Protocol > IGMP > IGMP Interface Setting, as shown below: Figure 6-69 IGMP Interface Settings Window The fields that can be configured are described below:...
Page 243 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide IGMP Static Group Settings Page This window is used to display and configure the IGMP static group settings. To view the following window, click L3 Features > IP Multicast Routing Protocol > IGMP > IGMP Static Group...
Page 244 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Clear button to clear all the information for the specific interface. Click the Clear All button to clear all the information in this table. Click the Delete button to delete the specified entry.
Page 245: Pim
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Please Select button, the following page will appear. Figure 6-75 IGMP SSM Mapping Settings (Please Select) Window Click the OK button to close the window and return to the previous window.
Page 246 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description PIM State Select this option to enable or disable the PIM protocol state. The default state is disabled.
Page 247 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide PIM RP Address page This window is used to display and configure the PIM RP address settings. To view the following window, click L3 Features > IP Multicast Routing Protocol > PIM > PIM for IPv4 > PIM RP...
Page 248 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Interface Name Specifies the Interface name. Group Address Specifies the IP multicast group address. Group Mask Specifies the IP multicast group mask. Click the Apply button to accept the changes made.
Page 249: Ipmc
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. IPMC Control Packet CPU Filtering This window is used to display and configure the IPMC control packet CPU filtering settings.
Page 250: Ip Route Filter
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this display here. From Port - To Port Select the range of ports that will be used for this display here.
Page 251 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 6-85 Route Map (Match Clauses, Edit) Window The fields that can be configured are described below: Parameter Description Action Select Add to add a new entry based in the information entered.
Page 252 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Back button to return to the previous window. After clicking the Edit button in the Set Clauses column, the following page will appear. Figure 6-86 Route Map (Set Clauses, Edit) Window...
Page 253: Policy Route
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Recursive - Specifies the IPv6 address of the recursive as the next-hop router. Enter the recursive next-hop IPv6 address in the space provided here. IPv6 Precedence Select the IPv6 precedence option here. Options to choose from are Routine, Priority, Immediate, Flash, Flash Override, Critical, Internet, and Network.
Page 254: Vrrp Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Route Map Enter the route map name here that will be used in this policy route entry. Click the Apply button to accept the changes made.
Page 255 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured in Virtual Router Settings are described below: Parameter Description VLAN Enter the VLAN interface ID used here. The range is from 1 to 4094.
Page 256: Vrrpv3 Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Shutdown Select to enable or disable the shutdown feature here. This feature is used to disable a virtual router on an interface. Avoid the common mistake of shutting down the IP address owner router before shutting down other non-owner routers.
Page 257 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit button next to the IPv4 Address Family entry, the following window will appear: Figure 6-92 VRRPv3 Settings (Edit, IPv4) Window The fields that can be configured are described below:...
Page 258 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit button next to the IPv6 Address Family entry, the following window will appear: Figure 6-93 VRRPv3 Settings (Edit, IPv6) Window The fields that can be configured are described below:...
Page 259: Quality Of Service (Qos)
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Quality of Service (QoS) Basic Settings Advanced Settings WRED Basic Settings Port Default CoS This window is used to display and configure the port default CoS settings. To view the following window, click QoS > Basic Settings > Port Default CoS, as shown below:...
Page 260 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 7-2 Port Scheduler Method Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 261: Queue Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Queue Settings This window is used to display and configure the queue settings. To view the following window, click QoS > Basic Settings > Queue Settings, as shown below:...
Page 262: Port Rate Limiting
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 7-4 CoS to Queue Mapping Window The fields that can be configured are described below: Parameter Description Queue ID Select the queue ID that will be mapped to the corresponding CoS value.
Page 263: Queue Rate Limiting
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description When Bandwidth is selected, enter the input/output bandwidth value • used in the space provided. This value must be between 8 and 10000000 kbps. Also, enter the Burst Size value in the space provided.
Page 264: Advanced Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description When the minimal bandwidth is configured, the packet transmitted from the queue can be guaranteed. When the maximum bandwidth is configured, packets transmitted from the queue cannot exceed the maximum bandwidth even if the bandwidth is available.
Page 265: Port Trust State And Mutation Binding
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Mutation Name Enter the DSCP mutation map name here. This name can be up to 32 characters long. Input DSCP List Enter the input DSCP list value here. This value must be between 0 and 63.
Page 266: Cos Color Mapping
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 7-9 DSCP CoS Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 267: Dscp Color Mapping
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 7-10 CoS Color Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 268: Class Map
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 7-11 DSCP Color Mapping Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 269: Aggregate Policer
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Match button to configure the specific entry. Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 270 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click QoS > Advanced Settings > Aggregate Policer, as shown below: Figure 7-14 Aggregate Policer (Single Rate Setting) Window The fields that can be configured are described below:...
Page 271 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description When selecting the Set-1P-Transmit option, enter the 1P transmit • value in the space provided. This value sets the 802.1p value and transmits the packet with the new value.
Page 272 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Aggregate Policer Name Enter the aggregate policer name here. Enter the Committed Information Rate (CIR) value here. This value must be between 0 and 10000000 kbps.
Page 273: Policy Map
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description action is not specified, the default action is equal to the exceed action. Options to choose from are Drop, Set-DSCP-Transmit, Set-1P-Transmit, Transmit, and Set-DSCP-1P. When selecting the Drop option, the packet will be dropped.
Page 274 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured for Traffic Policy are described below: Parameter Description Policy Map Name Enter the policy map name here. This name can be up to 32 characters long.
Page 275 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. After clicking the Policer button, the following page will appear. Figure 7-18 Policy Map (Policer) Window The fields that can be configured are described below:...
Page 276: Policy Binding
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Set-1P-Transmit - Specifies that the exceed action is to modify the 802.1p value and then to transmit the packet with the new 802.1p value. Enter the new 802.1p value in the space provided.
Page 277: Wred
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the range of ports that will be used for this configuration here.
Page 278: Wred Queue
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Profile Enter the WRED profile ID here. The range is from 1 to 128. Packet Colour Select the packet color here. Options to choose from are Green, Yellow, and Red.
Page 279 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description WRED State Select to enable or disable the WRED feature state on the specified port(s) here. Profile Enter the WRED profile ID here. The range is from 1 to 128.
Page 280: Access Control List (Acl)
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Access Control List (ACL) ACL Configuration Wizard ACL Access List ACL Interface Access Group ACL VLAN Access Map ACL VLAN Filter CPU ACL ACL Configuration Wizard This window is used to guide the user to create a new ACL access list or configure an existing ACL access list.
Page 281: Step 2 - Select Packet Type
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Create Select this option to create a new ACL access list using the configuration wizard. ACL Name Enter the new ACL name here. This name can be up to 32 characters long.
Page 282 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 8-4 ACL Configuration Wizard (Create, Packet Type, MAC) Window The fields that can be configured are described below: Parameter Description Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535.
Page 283 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Select the CoS value that will be used here. The range is from 0 to 7. • Mask - Enter the CoS mask value here. The range is from 0x0 to 0x7.
Page 284 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535. Select Auto Assign to automatically generate an ACL rule number for this entry.
Page 285 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description This parameter is only available in the protocol type TCP and UDP. Destination Port Select and enter the destination port value here. Options to choose from are =, >, <, ≠, Range, and Mask.
Page 286 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description TCP Flag Tick the appropriate TCP flag option to include the flag in this rule. Options to choose from are ack, fin, psh, rst, syn, and urg.
Page 287 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in Assign rule criteria are described below: Parameter Description Source Select and enter the source information here. Options to choose from are Any, Host, and IPv6.
Page 288: Step 4 - Apply Port
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the drop-down list. • When selecting the Mask option, the specified destination port number and mask will be used.
Page 289: Acl Access List
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 8-7 ACL Configuration Wizard (Create, Port) Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 290 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Add ACL button to create a new ACL. Click the Edit button to re-configure the specific ACL. Click the Delete button, next to the ACL, to remove the specific ACL.
Page 291: Standard Ip Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description ACL Type Select the ACL type that will be created here. Options to choose from are Standard IP ACL, Extended IP ACL, Standard IPv6 ACL, Extended IPv6 ACL, Extended MAC ACL, and Extended Expert ACL.
Page 292: Extended Ip Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Destination Select and enter the destination information here. Options to choose from are Any, Host, IP, and Wildcard. • When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 293 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Value - The protocol ID can also manually be entered here. The range is from 0 to 255. • Mask - After selecting the Protocol ID option, manually enter the protocol mask value here.
Page 294 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • When selecting the ≠ option, all ports, excluding the selected port, will be used. • When selecting the Range option, the start port number and end port number selected, of the range, will be used.
Page 295: Standard Ipv6 Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Standard IPv6 ACL After selecting a Standard IPv6 ACL and clicking the Add Rule button, the following page will appear. Figure 8-13 Standard IPv6 ACL (Add Rule) Window The fields that can be configured are described below:...
Page 296: Extended Ipv6 Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Extended IPv6 ACL After selecting an Extended IPv6 ACL and clicking the Add Rule button, the following page will appear. Figure 8-14 Extended IPv6 ACL (Add Rule) Window The fields that can be configured are described below:...
Page 297 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. • When the Host option is selected, enter the destination host IPv6 address here.
Page 298: Extended Mac Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description This parameter is only available in the protocol type ICMP. Message Code When the ICMP Message Type is not selected, enter the ICMP Message Type numerical value used here. When the ICMP Message Type is selected, this numerical value will automatically be entered.
Page 299 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Sequence No. Enter the sequence number of this ACL rule here. The range is from 1 to 65535. If this value is not specified, the system will automatically generate an ACL rule number for this entry.
Page 300: Extended Expert Acl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Extended Expert ACL After selecting an Extended Expert ACL and clicking the Add Rule button, the following page will appear. Figure 8-16 Extended Expert ACL (Add Rule) Window The fields that can be configured are described below:...
Page 301 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description When the Any option is selected, any destination traffic will be • evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host IP address •...
Page 302 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the drop-down list. When selecting the Mask option, the specified destination port number •...
Page 303: Acl Interface Access Group
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Inner CoS After selecting the CoS value, select the inner CoS value that will be used here. The range is from 0 to 7. Mask - Enter the inner CoS mask value here. The range is from 0x0 to •...
Page 304: Acl Vlan Access Map
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 8-188 ACL Interface Access Group (Please Select) Window Select the radio button next to the entry to use that ACL in the configuration. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 305 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Binding button, the following window will appear:...
Page 306: Acl Vlan Filter
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Select the radio button next to the entry to use that access list in the configuration. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 307 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Filter Map Name Enter the CPU ACL filter map name here. This name can be up to 32 characters long. Click the Apply button to accept the changes made.
Page 308 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description ACL Name Enter the standard or extended IPv6 access list name to be matched here. This name can be up to 32 characters long. Alternatively, click the Please Select button to select an existing ACL from the list.
Page 309 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description ACL List Select the radio button next to the access list entry to use that access list in the configuration.
Page 310: Security
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Security Port Security 802.1X RADIUS TACACS IMPB DHCP Server Screening ARP Spoofing Prevention BPDU Attack Protection MAC Authentication Web-based Access Control Network Access Authentication Safeguard Engine Trusted Host Traffic Segmentation Settings...
Page 311: Port Security Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Trap State Select to enable or disable port security traps on the Switch. Click the Apply button to accept the changes made. The fields that can be configured in Port Security Trap Rate Settings are described below:...
Page 312 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-2 Port Security Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 313: Port Security Address Entries
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Port Security Address Entries This window is used to view, clear and configure the port security address entries. To view the following window, click Security > Port Security > Port Security Address Entries, as shown below:...
Page 314 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-4 The EAPOL Packet Utilizing this method, unauthorized devices are restricted from connecting to a LAN through a port to which the user is connected. EAPOL packets are the only traffic that can be transmitted through the specific port until authorization is granted.
Page 315 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-6 The Authentication Server Authenticator The Authenticator (the Switch) is an intermediary between the Authentication Server and the Client. The Authenticator serves two purposes when utilizing the 802.1X function. The first purpose is to request certification information from the Client through EAPOL packets, which is the only information allowed to pass through the Authenticator before access is granted to the Client.
Page 316 Figure 9-9 The 802.1X Authentication Process The D-Link implementation of 802.1X allows network administrators to choose between two types of Access Control used on the Switch, which are: • Port-based Access Control - This method requires only one user to be authenticated per port by a remote RADIUS server to allow the remaining users on the same port access to the network.
Page 317 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The original intent behind the development of 802.1X was to leverage the characteristics of point-to-point in LANs. As any single LAN segment in such infrastructures has no more than two devices attached to it, one of which is a Bridge Port.
Page 318: 802.1X Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-11 Example of Typical Host-based Configuration 802.1X Global Settings This window is used to display and configure the global 802.1X settings. To view the following window, click Security > 802.1X > 802.1X Global Settings, as shown below: Figure 9-12 802.1X Global Settings Window...
Page 319: Authentication Sessions Information
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-13 802.1X Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 320: Authenticator Statistics
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-14 Authentication Sessions Information Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 321: Authenticator Session Statistics
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Authenticator Session Statistics This window is used to view and clear the authenticator session statistics. To view the following window, click Security > 802.1X > Authenticator Session Statistics, as shown below:...
Page 322: Aaa
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-17 Authenticator Diagnostics Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this query here.
Page 323: Application Authentication Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description AAA State Select to enable or disable the global Authentication, Authorization, and Accounting (AAA) state. Click the Apply button to accept the changes made. Application Authentication Settings This window is used to display and configure the application authentication settings.
Page 324 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-21 Application Accounting Settings Window Click the Edit button to re-configure the specific entry. Figure 9-22 Application Accounting Settings (Edit) Window The fields that can be configured in Application Accounting Exec Method list are described below:...
Page 325: Authentication Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Authentication Settings This window is used to display and configure the AAA network and EXEC authentication settings. To view the following window, click Security > AAA > Authentication Settings, as shown below: Figure 9-23 Authentication Settings Window The fields that can be configured in AAA Authentication 802.1X are described below:...
Page 326 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • radius - Specifies to use the servers defined by the RADIUS server host command. Click the Apply button to accept the changes made. The fields that can be configured in AAA Authentication WEB-Auth are described below:...
Page 327: Accounting Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Method 1 ~ Method 4 Select the method lists that will be used for this configuration here. Options to choose from are: • none - Normally, the method is listed as the last method. The user will pass the authentication if it is not denied by previous method authentication.
Page 328 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Default Select to enable or disable the use of the default method list here. Method 1 ~ Method 4 Select the method lists that will be used for this configuration here. Options to choose from are none, group, radius, and tacacs+.
Page 329: Radius
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-28 Accounting Settings (AAA Accounting Commands) Window The fields that can be configured are described below: Parameter Description Level Select the privilege level used here. Options to choose from are levels 1 to 15.
Page 330: Radius Server Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description improve the authentication processing time by setting the dead time to skip the unresponsive server host entries. When the system performs authentication with the authentication server, it attempts one server at a time.
Page 331: Radius Group Server Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Address Enter the RADIUS server IPv4 address here. IPv6 Address Enter the RADIUS server IPv6 address here.
Page 332: Radius Statistic
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will be available. Figure 9-32 RADIUS Group Server Settings (Detail) Window The fields that can be configured are described below:...
Page 333: Tacacs
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Group Server Name Select the RADIUS group server name from this list here. Click the Clear button to clear the information based on the selections made.
Page 334: Tacacs Group Server Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Address Enter the TACACS+ server IPv4 address here. Port Enter the port number used here. This value must be between 1 and 65535. By default, this value is 49.
Page 335: Tacacs Statistic
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-37 TACACS Group Server Settings (Show Detail) Window The fields that can be configured are described below: Parameter Description IPv4 TACACS Source Enter the name of the source IPv4 TACACS+ interface here.
Page 336: Ipv4
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide saving them to the IMPB white list. If an unauthorized user tries to access an IP-MAC binding enabled port, the system will block the access by dropping its packet. Active and inactive entries use the same database. The function is port-based, meaning a user can enable or disable the function on the individual port.
Page 337 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-40 DHCP Snooping Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 338 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description State Select to enable or disable the DHCP snooping VLAN setting here. Click the Apply button to accept the changes made. DHCP Snooping Database This window is used to display and configure the DHCP snooping database settings.
Page 339 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Select the location from the drop-down list and enter the URL where the DHCP snooping database will be stored to here. Locations to choose from are TFTP, FTP, and Flash.
Page 340 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Dynamic ARP Inspection ARP Access List This window is used to display and configure the dynamic ARP inspection settings. To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP Access List, as...
Page 341 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Select the type of sender MAC address that will be used here. Options to choose from are Any, Host, and MAC with Mask. Sender MAC After selecting the Host or MAC with Mask options as the type of MAC, enter the sender MAC address used here.
Page 342 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description addresses are dropped. Sender IP addresses are checked in all ARP requests and responses, and target IP addresses are checked only in ARP responses. Click the Apply button to accept the changes made.
Page 343 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Set to Default button to change the information to the default values. ARP Inspection VLAN This window is used to display and configure the ARP inspection VLAN settings.
Page 344 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP Inspection Log, as shown below: Figure 9-50 ARP Inspection Log Window The fields that can be configured are described below:...
Page 345 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide IP Source Guard Binding This window is used to display and configure the IP source guard binding settings. To view the following window, click Security > IMPB > IPv4 > IP Source Guard > IP Source Guard Binding, as...
Page 346 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Delete button to remove the specified entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 347 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-54 IP-MAC-Port Binding Settings Window The fields that can be configured in IP-MAC-Port Binding Trap Settings are described below: Parameter Description Trap State Select the enable or disable the IP-MAC-Port binding option’s trap state.
Page 348: Ipv6
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-55 IP-MAC-Port Binding Blocked Entry Window The fields that can be configured are described below: Parameter Description Clear by Port Select this option to clear the entry table based on the port(s) selected.
Page 349 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in IPv6 Snooping Policy Settings are described below: Parameter Description Policy Name Enter the IPv6 snooping policy name used here. This name can be up to 32 characters long.
Page 350 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After selecting the IPv6 Snooping DHCP Entry Settings tab option, the following page will be available. Figure 9-577 IPv6 Snooping (IPv6 Snooping DHCP Entry Settings) Window The fields that can be configured are described below:...
Page 351 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Binding Max Entries Enter the maximum number of IPv6 snooping binding entries that is allowed here. The range is from 0 to 1024. Click the Apply button to accept the changes made.
Page 352 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Policy Name Enter the policy name used here. This name can be up to 32 characters long. Device Role Select the device role here.
Page 353 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description device's role is Router, RA packets will be forwarded according to the port's bound ACL. Match IPv6 Access List Enter or select the IPv6 access list to match here. Click the Please Select button to select an existing ACL from the list.
Page 354 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Device Role Select the device role here. Options to choose from are Client and Server. By default, the device's role is set as Client, which will block all the DHCPv6 packets from the DHCPv6 Server.
Page 355 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-615 IPv6 Source Guard Settings Window The fields that can be configured are described below: Parameter Description Policy Name Enter the policy name here. This name can be up to 32 characters long.
Page 356: Dhcp Server Screening
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-626 IPv6 Neighbor Binding Window The fields that can be configured in IPv6 Neighbor Binding Settings are described below: Parameter Description MAC Address Enter the MAC address used here.
Page 357: Dhcp Server Screening Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide When the DHCP Server Screening function is enabled on a port, all DHCP server packets received on this ports will be redirected to the CPU for a software-based check. Legal DHCP server packets will be forwarded out and illegal DHCP server packets will be dropped.
Page 358: Dhcp Server Screening Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. Click the Clear Log button to clear the log. DHCP Server Screening Port Settings This window is used to display and configure the DHCP server screening port settings.
Page 359: Bpdu Attack Protection
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-659 ARP Spoofing Prevention Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 360: Mac Authentication
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-70 BPDU Attack Protection Window The fields that can be configured in BPDU Attack Protection Global Settings are described below: Parameter Description BPDU Attack Protection Select to enable or disable the global BPDU attack protection state here.
Page 361 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-71 MAC Authentication Window The fields that can be configured in MAC Authentication Global Settings are described below: Parameter Description MAC Authentication State Select to enable or disable the global MAC authentication state.
Page 362: Web-Based Access Control
WAC by attempting to gain Web access. D-Link’s implementation of WAC uses a virtual IP that is exclusively used by the WAC function and is not known by any other modules of the Switch. In fact, to avoid affecting a Switch’s other features, WAC will only use a virtual IP address to communicate with hosts.
Page 363 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-72 RADIUS Authentication Server Conditions and Limitations • If the client is utilizing DHCP to attain an IP address, the authenticating VLAN must provide a DHCP server or a DHCP relay function so that client may obtain an IP address.
Page 364: Web Authentication
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Web Authentication This window is used to display and configure the Web authentication settings. To view the following window, click Security > Web-based Access Control > Web Authentication, as shown below:...
Page 365: Wac Customize Page
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-674 WAC Port Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 366: Network Access Authentication
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Page Title Enter a custom page title message here. This message can be up to 128 characters. Login Window Title Enter a custom login window title here.
Page 367 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Security > Network Access Authentication > Network Access Authentication Global Settings, as shown below: Figure 9-707 Network Access Authentication Global Settings Window The fields that can be configured in Network Access Authentication MAC Format Settings are described below:...
Page 368: Network Access Authentication Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description RADIUS server will be accepted if the authorization status is enabled. Bandwidth and ACL are assigned on a per-port basis. If in the multi- authenticated mode, VLAN and 802.1p are assigned on a per-host basis.
Page 369: Network Access Authentication Sessions Information
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the appropriate port range used for the configuration here.
Page 370: Safeguard Engine
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-729 Network Access Authentication Sessions Information Window The fields that can be configured are described below: Parameter Description Port Select the appropriate Switch unit and port used for the query here.
Page 371: Safeguard Engine Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Protocol Name Sub-interface Description (Group) 802.1X Protocol Port-based Network Access Control Protocol Address resolution Protocol DHCP Protocol Dynamic Host Configuration Protocol Protocol Domain Name System GVRP Protocol GARP VLAN Registration Protocol...
Page 372: Cpu Protect Counters
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-80 Safeguard Engine Settings Window The fields that can be configured in Safeguard Engine Settings are described below: Parameter Description Safeguard Engine State Select to enable or disable the safeguard engine feature here.
Page 373: Cpu Protect Sub-Interface
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Clear button to clear the information based on the selections made. Click the Clear All button to clear all the information in this table. CPU Protect Sub-Interface This window is used to display and configure the CPU protection sub-interface settings.
Page 374: Trusted Host
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-733 CPU Protect Type Window The fields that can be configured in CPU Protect Type are described below: Parameter Description Protocol Name Select the protocol name option here.
Page 375: Traffic Segmentation Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Traffic Segmentation Settings This window is used to display and configure the traffic segmentation settings. When the traffic segmentation forwarding domain is specified, packets received by the port will be restricted in Layer 2 packet forwarding to interfaces within the domain.
Page 376 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-766 Storm Control Window The fields that can be configured in Storm Control Trap Settings are described below: Parameter Description Trap State Select the storm control trap option here. Options to choose from are None, Storm Occur, Storm Clear, and Both.
Page 377 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description and 2147483647 packets per second. If the low PPS value is not specified, the default value is 80% of the specified risen PPS. PPS Low Enter the low packets per second value here. This option specifies the low threshold value in packets count per second.
Page 378: Dos Attack Prevention Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide DoS Attack Prevention Settings This window is used to display and configure the Denial-of-Service (DoS) attack prevention settings. The following well-known DoS types which can be detected by most Switches: •...
Page 379: Ssh
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Trap State Select to enable or disable the DoS attack prevention trap state here. Click the Apply button to accept the changes made. The fields that can be configured in DoS Attack Prevention Settings are described below:...
Page 380: Host Key
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP SSH Server State Select to enable or disable the global SSH server state. IP SSH Service Port Enter the SSH service port number used here.
Page 381: Ssh Server Connection
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-92 Host Key (Generating) Window After the key was successfully generated, the following window will appear. Figure 9-803 Host Key (Generating, Success) Window SSH Server Connection This window is used to view the SSH server connections table.
Page 382: Ssl
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Authentication Method Select the authentication methods used here. Options to choose from are Password, Public Key, and Host-based. Key File After selecting the Public Key or Host-based option as the Authentication Method, enter the public key here.
Page 383: Ssl Global Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide SSL Global Settings This window is used to display and configure the global SSL settings. To view the following window, click Security > SSL > SSL Global Settings, as shown below:...
Page 384: Ssl Service Policy
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-847 Crypto PKI Trustpoint Window The fields that can be configured are described below: Parameter Description Trustpoint Enter the name of the trust-point that is associated with the imported certificates and key pairs here.
Page 385: Sftp Server Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-858 SSL Service Policy Window The fields that can be configured are described below: Parameter Description Policy Name Enter the SSL service policy name here. This name can be up to 32 characters long.
Page 386 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 9-869 SFTP Server Settings Window The fields that can be configured are described below: Parameter Description SFTP Server Select to globally enable or disable the SFTP server feature here.
Page 387: 10. Oam
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide 10. OAM Cable Diagnostics Ethernet OAM CFM Settings This window is used to display and configure the Connectivity Fault Management (CFM) settings. To view the following window, click OAM > CFM > CFM Settings, as shown below:...
Page 388 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description facilitates easy identification of administrative responsibility for each maintenance domain. Domain Level Enter the Maintenance Domain (MD) level here. The range is from 0 to 7. A unique MD level is assigned to define the hierarchical relationship between domains.
Page 389 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Chassis - Specifies to transmit the sender ID TLV with the chassis ID information. • Manage - Specifies to transmit the sender ID TLV with the managed address information.
Page 390 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured in the table are described below: Parameter Description MA Mode Select the MA mode here. Options to choose from are: • Software - Specifies that the MA works in the CFM software mode.
Page 391 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Add MEP button, the following page will appear. Figure 10-5 CFM Settings (Add MA, Add MEP) Window The fields that can be configured are described below:...
Page 392 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 10-6 CFM Settings (Add MA, Add MEP, MEPID Detail) Window Click the Edit button to modify the specified entry.
Page 393 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit button, the following page will appear. Figure 10-7 CFM Settings (Add MA, Add MEP, MEPID Detail, Edit) Window The fields that can be configured are described below:...
Page 394 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Alarm Time Enter the time period used to define the time from when a defect is detected on the MEP to when a fault alarm will be sent. The range is from 250 to 1000 centiseconds.
Page 395 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Edit DM button, the following page will appear. Figure 10-10 CFM Settings (Add MA, Add MEP, Edit DM) Window The fields that can be configured in CFM DM Settings are described below:...
Page 396 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured in Clear CFM DM are described below: Parameter Description Type Select the type of information to clear here. Options to choose from are: •...
Page 397: Cfm Port Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Period Select the time period here. This specifies the transmitting interval of the LM PDU. Options to choose from are 100ms, 1sec, and 10sec. PDU Priority Select the PDU priority value here. The range is from 0 to 7. This specifies the 802.1p priority to be set in the LMM messages transmitted by the MEP.
Page 398: Cfm Loopback Test
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide After clicking the Show Detail button, the following page will appear. Figure 10-13 CFM Port Settings (View Detail) Window Click the Back button to return to the previous window.
Page 399: Cfm Linktrace Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description PDU Priority Select the 802.1p priority to be set in the transmitted LBMs here. If not specified, it uses the same priority as the CCMs sent by the MA. The range is from 0 to 7.
Page 400: Cfm Packet Counter
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Clear button to clear the entries based on the information specified. Click the Clear All button to clear the information associated with all entries. Click the Show Detail button to view more detailed information about the link-trace entry.
Page 401: Cfm Counter Ccm
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Clear All button to clear the counter information associated with all entries. CFM Counter CCM This window is used to view and clear the CFM CCM counter information.
Page 402: Cable Diagnostics
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service representatives to verify and test copper cables; it can rapidly determine the quality of the cables and the types of error.
Page 403: Ethernet Oam
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Ethernet OAM Ethernet OAM Settings This window is used to display and configure the Ethernet Operations, Administration, and Maintenance (OAM) settings. To view the following window, click OAM > Ethernet OAM > Ethernet OAM Settings, as shown below:...
Page 404: Ethernet Oam Configuration Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description traffic will not be processed. Ignoring the received remote loopback feature will prevent the port from entering the remote loopback mode. Remote Loopback Select the remote loopback action here. Options to choose from are Start and Stop.
Page 405 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 10-223 Ethernet OAM Configuration Settings Window The fields that can be configured in Ethernet OAM Configuration Settings are described below: Parameter Description Unit Select the Switch unit ID that will be used here.
Page 406 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Error Frame Seconds - This feature is used to enable notifying the Ethernet OAM error frame second event and configure the monitor threshold and window on the specified port.
Page 407: Ethernet Oam Event Log Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Show All button to display all the entries. Ethernet OAM Event Log Table This window is used to view and clear the Ethernet OAM event log table.
Page 408: Ethernet Oam Duld Settings
Click the Show All button to display all the statistics information. Ethernet OAM DULD Settings This window is used to display and configure the Ethernet OAM D-Link Unidirectional Link Detection (DULD) settings. DULD is an extension of 802.3ah Ethernet OAM. It provides a mechanism to detect a unidirectional point-to-point Ethernet link without PHY support.
Page 409 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click OAM > Ethernet OAM > Ethernet OAM DULD Settings, as shown below: Figure 10-26 Ethernet OAM DULD Settings Window The fields that can be configured in Ethernet OAM DULD Settings are described below:...
Page 410: Ddm
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide This folder contains windows that perform Digital Diagnostic Monitoring (DDM) functions on the Switch. There are windows that allow the user to view the digital diagnostic monitoring status of SFP/SFP+ modules inserting to the Switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings, bias current threshold settings, Tx power threshold settings, and Rx power threshold settings.
Page 411: Ddm Temperature Threshold Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description • Warning - Shutdown the port when the configured warning threshold range is exceeded. • None - The port will never shutdown regardless if the threshold ranges are exceeded or not.
Page 412: Ddm Bias Current Threshold Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 10-29 DDM Voltage Threshold Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 413: Ddm Tx Power Threshold Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Value Enter the threshold value. This value must be between 0 and 131 mA. Click the Apply button to accept the changes made. DDM TX Power Threshold Settings This window is used to display and configure the threshold of TX power for specific ports on the Switch.
Page 414: Ddm Status Table
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 10-282 DDM RX Power Threshold Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 415: 11. Monitoring
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide 11. Monitoring VLAN Counter Utilization Statistics Mirror Settings sFlow Device Environment VLAN Counter This window is used to display and configure the VLAN counter settings. This is used to create a control entry for traffic statistics on specified Layer 2 VLAN interface(s).
Page 416: Utilization
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured for VLAN Counter Table are described below: Parameter Description Interface VLAN Enter the VLAN ID that will be used here. The range is from 1 to 4094. Select the All option to display counter information associated with all VLAN interfaces.
Page 417 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-2 History Utilization (Memory) Window After selecting CPU as the Type, the following window will appear: Figure 11-3 History Utilization (CPU) Window After selecting Port as the Type, the following window will appear:...
Page 418: Statistics
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Time Based Select the time-based statistical count value here. Options to choose from are: • 15 Minutes - Specifies to display 15-minute based statistics count. • 1 Day - Specifies to display daily based statistics count.
Page 419: Cpu Port
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-7 Port (Show Detail) Window Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table. CPU Port...
Page 420: Interface Counters
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Monitoring > Statistics > CPU Port, as shown below: Figure 11-5 CPU Port Window The fields that can be configured are described below:...
Page 421 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-9 Interface Counters (Port) Window The fields that can be configured are described below: Parameter Description Type Select the type of information to display here. Option supports Port.
Page 422: Interface History Counters
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table. After selecting VLAN as the Type, the following window will appear:...
Page 423: Counters
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-7 Interface History Counters (Port) Window The fields that can be configured are described below: Parameter Description Type Select the type of information to display here. Unit Select the Switch unit that will be used in this display here.
Page 424 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To view the following window, click Monitoring > Statistics > Counters, as shown below: Figure 11-13 Counters (Port) Window The fields that can be configured are described below: Parameter...
Page 425: Mirror Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-14 Counters (Show Detail) Window Click the Back button to return to the previous window. Click the Refresh button to refresh the information displayed in the table. Mirror Settings This window is used to display and configure the mirror feature’s settings.
Page 426 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-15 Mirror Settings Window The fields that can be configured for RSPAN VLAN Settings are described below: Parameter Description VID List Enter the VLAN list ID(s) that will be associated with this configuration here.
Page 427: Sflow
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description traffic in only the incoming direction will be mirrored. When selecting TX, traffic in only the outgoing direction will be mirrored. Select the CPU RX option to also monitor CPU RX traffic.
Page 428: Sflow Receiver Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-87 sFlow Agent Information Window sFlow Receiver Settings This window is used to display and configure receivers for the sFlow agents. Receivers cannot be added to or removed from the sFlow agent.
Page 429: Sflow Poller Settings
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 11-109 sFlow Sampler Settings Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 430: Device Environment
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the appropriate port range used for the configuration here.
Page 431: 12. Green
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide 12. Green Power Saving Power Saving This window is used to display and configure the power saving settings of the Switch. To view the following window, click Green > Power Saving, as shown below:...
Page 432: Eee
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide NOTE: The hibernation feature can only be configured when physical stacking is disabled on this Switch. After clicking the Power Saving Shutdown Settings tab, the following page will appear.
Page 433 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here. From Port - To Port Select the appropriate port range used for the configuration here.
Page 434: 13. Save And Tools
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide 13. Save and Tools Save Configuration Firmware Upgrade & Backup Configuration Restore & Backup Log Backup Ping Trace Route Reset Reboot System Save Configuration This window is used to save the running configuration to the start-up configuration. This is to prevent the loss of configuration in the event of a power failure.
Page 435: Firmware Upgrade From Tftp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Source File In this field the source firmware file’s filename and path will be displayed after selection. To navigate to the location of the firmware file located on the local PC, either double click in the text box or click the Browse button.
Page 436: Firmware Backup To Tftp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Unit Select the Switch unit that will be used for this configuration here. Source File Enter the source filename and path of the firmware file located on the Switch here.
Page 437: Configuration Restore From Tftp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 13-6 Configuration Restore from HTTP Window The fields that can be configured are described below: Parameter Description Unit Select the Switch unit that will be used for this configuration here.
Page 438: Configuration Backup To Http
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description the Switch. Select the startup-config option to restore and overwrite the start- up configuration file on the Switch. Replace Select this option to replace the configuration file on the Switch with this one.
Page 439: Log Backup
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description TFTP Server IP Enter the TFTP server IP address here. When select the IPv4 option, enter the IPv4 address of the TFTP server in the space provided. When the IPv6 option is selected, enter the IPv6 address of the TFTP server in the space provided.
Page 440: Ping
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description TFTP Server IP Enter the TFTP server IP address here. When select the IPv4 option, enter the IPv4 address of the TFTP server in the space provided. When the IPv6 option is selected, enter the IPv6 address of the TFTP server in the space provided.
Page 441 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description ACL Name Enter the name of the ACL that will be used here. This name can be up to 32 characters long. Click the Please Select button to select an existing ACL from the list.
Page 442: Trace Route
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description Source IPv6 Address Enter the source IPv6 address. If the current Switch has more than one IPv6 address, you can enter one of them to this field. When entered, this IPv6 address will be used as the packets’...
Page 443 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Figure 13-15 Trace Route Window The fields that can be configured in IPv4 Trace Route are described below: Parameter Description IPv4 Address Select and enter the IPv4 address of the destination here.
Page 444: Reset
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Parameter Description IPv6 Address Select and enter the IPv6 address of the destination here. Domain Name Select and enter the domain name of the destination here. Initial TTL Enter the initial Time-To-Live (TTL) value here. The range is from 1 to 255.
Page 445: Reboot System
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide • The Switch will reset to its factory default settings and not reboot. This option excludes the stacking information. Click the Apply button to initiate the reset. Reboot System This window is used to reboot the Switch and alternatively save the configuration before doing so.
Page 446: Appendix A - Password Recovery Procedure
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Appendix A - Password Recovery Procedure This section describes the procedure for resetting passwords on the D-Link DGS-3130 Series Switch. Authenticating any user who tries to access networks is necessary and important. The basic authentication method used to accept qualified users is through a local login, utilizing a Username and Password.
Page 447: Appendix B - System Log Entries
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Appendix B - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this Switch. 802.1X Log Description Severity Event description: 802.1X Authentication failure.
Page 448 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity server-ip: It indicates the AAA server IP address if authentication method is remote server. username: It indicates the username for authentication. Event description: Login failed due to AAA server timeout or improper configuration.
Page 449: Arp
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Log Message: RADIUS server <server-ip> assigned <direction> bandwidth: <threshold> to port <interface-id> (Username: <username>) Parameters description: server-ip: It indicates the RADIUS server IP address. direction: It indicates the direction for bandwidth control, e.g.: ingress or egress.
Page 450: Bpdu Protection
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity ipaddr: Represent client IP address BPDU Protection Log Description Severity Event description: Record the event when the BPDU attack happened. Informational Log Message: <interface-id> enter STP BPDU under protection state (mode: <mode>) Parameters description: interface-id: Interface on which detected STP BPDU attack.
Page 451 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Log Message: CFM remote down. MD Level:<mdlevel>, VLAN:<vlanid>, Local(Interface:<interface-id>, Direction:<mepdirection>) Parameters Description: vlanid: Represents the VLAN identifier of the MEP. mdlevel: Represents the MD level of the MEP.
Page 452 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity mepid: Represents the MEPID of the MEP. Event Description: LCK condition detected. Notification Log Message: LCK condition detected. MD Level:<mdlevel>, VLAN:<vlanid>, Local(Interface:<interface-id>, Direction:<mepdirection>, MEPID:<mepid>) Parameters Description: vlanid: Represents the VLAN identifier of the MEP.
Page 453 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Log Message: [Unit <unitID>, ]Firmware uploaded by <session> successfully (Username: <username>[, IP: <ipaddr>, MAC: <macaddr>], Server IP: <serverIP>, File Name: <pathFile>) Parameters description: unitID: The unit ID.
Page 454 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity unitID: The unit ID. session: The user’s session. username: Represent current login user. ipaddr: Represent client IP address. macaddr : Represent client MAC address. serverIP: Server IP address.
Page 455 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Event description: when the any of SFP parameters exceeds from the warning Warning threshold. Log Message: Optical transceiver <interface-id> <component> <high-low> warning threshold exceeded. Parameters description: interface-id: port interface ID.
Page 456 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Parameters description: ipv6address: IPv6 address obtained from a DHCPv6 server. ipif-name: Name of the DHCPv6 client interface. Event description: The IPv6 address obtained from a DHCPv6 server starts renewing.
Page 457 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity intf-name: Name of the DHCPv6 client PD interface. DHCPv6 Server Log Description Severity Event description: The address of the DHCPv6 Server pool is used up Informational Log Message: The address of the DHCPv6 Server pool <pool-name>...
Page 458 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Log Message: "Force Switch is issued on node (MAC: <macaddr>, instance <InstanceID>)" Parameters description: macaddr: MAC address InstanceID: Instance ID Event description: Clear command is issued.
Page 459 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Parameters description: interface-id: The interface name. Event description: Errored Frame Seconds Summary Event Warning Log Message: Errored frame seconds summary event received (Port <interface-id>) Parameters description: interface-id: The interface name.
Page 460 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Event description: Link Aggregation Group link down. Informational Log Message: Link Aggregation Group <group_id> link down. Parameters description: group_id: The group id of the link down aggregation group.
Page 461 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide LLDP-MED Log Description Severity Event description: LLDP-MED topology change detected Notice Log Message: LLDP-MED topology change detected (on port <portNum>. chassis id: <chassisType>, <chassisID>, port id: <portType>, <portID>, device class: <deviceClass>)
Page 462 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity 5. interfaceName(5) 6. agentCircuitId(6) 7. local(7) portID: port ID. deviceClass: LLDP-MED device type. Event description: Incompatible LLDP-MED TLV set detected Notice Log Message: Incompatible LLDP-MED TLV set detected ( on port <portNum>, chassis id: <chassisType>, <chassisID>, port id: <portType>, <portID>, device class:...
Page 463 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Parameters description: unitID: The unit ID. username: Represent current login user. Event description: Logout through console. Informational Log Message: [Unit <unitID>, ] Logout through Console (Username: <username>) Parameters description: unitID: The unit ID.
Page 464 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Event description: the host has passed MAC authentication Informational Log Message: MAC-based Access Control host login success (MAC: <mac-address>, <interface-id>, VID: <vlan-id>) Parameters description: mac-address: the host MAC addresses.
Page 465 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity InstanceID: Instance ID. portNum: Port ID macaddr: MAC address Event description: Spanning Tree new Root Bridge Informational Log Message: [CIST | CIST Regional | MSTI Regional] New Root bridge selected( [Instance: <InstanceID>...
Page 466 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Log Message: Spanning Tree MST configuration ID name and revision level change (name:<name> revision level <revision_level>). Parameters description: name : New name. revision_level: New revision level.
Page 467 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity Unit <id>: The unit ID. power-descr: Describe the power. Event description: Power is recovered. Critical Log Message: Unit <unit-id> <power-descr> back to normal Parameters description: Unit <id>: The unit ID.
Page 468 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Safeguard Log Description Severity Event description: When the CPU utilization is over the rising threshold, the Switch Warning enters exhausted mode, and the syslog will be recorded. Log Message: Unit <unit-id>, Safeguard Engine enters EXHAUSTED mode.
Page 469 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity username: The username that used to login SSL server. ipaddr: The IP address of SSL client. Event description: Logout through Web (SSL). Informational Log Message: Logout through Web (SSL) (Username: <username>, IP: <ipaddr>).
Page 470 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Telnet Log Description Severity Event description: Successful login through Telnet. Informational Log Message: Successful login through Telnet (Username: <username>, IP: <ipaddr>) Parameters description: ipaddr: The IP address of telnet client.
Page 471 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Log Description Severity ipv6address: IPv6 address macaddr: MAC address unitID: The unit ID portNum : The port number Log Description Severity Event description: Successful login through Web. Informational Log Message: Successful login through Web (Username: <username>, IP: <ipaddr>).
Page 472 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Appendix C - Trap Entries The following table lists all possible trap log entries and their corresponding meanings that will appear in the Switch. 802.1X Trap Name Description esDot1xExtLoggedSuccess The trap is sent when a host has successfully logged in 1.3.6.1.4.1.17...
Page 473 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Authentication Fail Trap Name Description authenticationFailure An authenticationFailure trap signifies that the SNMPv2 1.3.6.1.6.3.1.1 entity, acting in an agent role, has received a protocol .5.5 message that is not properly authenticated. While all...
Page 474 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description (2) dCfmEventMaIndex (3) dCfmEventMepIdentifier dCfmLockCleared This trap is initiated when local MEP exits lock status. 1.3.6.1.4.1.17 1.14.86.0.4 Binding objects: (1) dCfmEventMdIndex (2) dCfmEventMaIndex (3) dCfmEventMepIdentifier Trap Name...
Page 475 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description (2) esDosPrevNotiInfoDropIpAddr (3) esDosPrevNotiInfoDropPortNumber ERPS Trap Name Description esErpsFailuredetectedNotif A esErpsFailureNotification is sent when 1.3.6.1.4.1.17 esErpsNotificationEnabled is 'true' and a signal failure is 1.17.78.0.1 detected. esErpsFailureClearedNotif A esErpsFailureClearedNotif is sent when 1.3.6.1.4.1.17...
Page 476 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description (1) esIpExtGratuitousARPIpAddr (2) esIpExtGratuitousARPMacAddr (3) esIpExtGratuitousARPPortNumber (4) esIpExtIfCfgIfIndex IP-MAC-Port Binding Trap Name Description dImpbViolationTrap The address violation notification is generated when IP- 1.3.6.1.4.1.17 MAC-Port Binding address violation is detected.
Page 477 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description Binding objects: (1) esLbdNotifyInfoIfIndex esLbdVlanLoopOccurred The trap is sent when a port loop occurs under LBD 1.3.6.1.4.1.17 VLAN-based mode. 1.17.46.0.3 Binding objects: (1) esLbdNotifyInfoIfIndex (2) esLbdNotifyInfoVlanId esLbdVlanLoopRestart 1.3.6.1.4.1.17...
Page 478 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description esMacAuthLoggedAgesOut The trap is sent when a MAC-based Access Control host 1.3.6.1.4.1.17 ages out. 1.17.153.0.3 Binding objects: (1) ifIndex, (2) esnaSessionClientMacAddress (3) esnaSessionAuthVlan MAC Notification Trap Name...
Page 479 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description Binding objects: (1) esEntityExtEnvTempUnitId (2) esEntityExtEnvTempIndex (3) esEntityExtEnvTempStatus esEntityExtPowerStatusChg The commander Switch will send this notification when a 1.3.6.1.4.1.17 power module fails, recovers or is removed.
Page 480 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description esPortSecMacAddrViolation When the port security trap is enabled, new MAC 1.3.6.1.4.1.17 addresses that violate the pre-defined port security 1.17.8.0.1 configuration will trigger trap messages to be sent out.
Page 481 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description esSafeguardChgToExhausted This trap indicates System change operation mode from 1.3.6.1.4.1.17 normal to exhaust. 1.17.19.1.1.0. Binding objects: (1) esSafeguardEngineCurrentMode esSafeguardChgToNormal This trap indicates system change operation mode from 1.3.6.1.4.1.17...
Page 482 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description (1) esSingleIpMSTrapMacAddr esSingleIpMSmacNotification The commander switch will send this notification to the 1.3.6.1.4.1.17 indicated host when its member generates a MAC 1.17.225.0.0.2 address variation notification. (1) esSingleIpMSTrapMacAddr...
Page 483: System File
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description esStormCtrlOccurred This trap is sent when esStormCtrlNotifyEnable is 1.3.6.1.4.1.17 'stormOccurred' or 'both' and a storm is detected. 1.17.25.0.1 Binding objects: (1) ifIndex, (2) esStormCtrlNotifyTrafficType esStormCtrlStormCleared This trap is sent when esStormCtrlNotifyEnable is 1.3.6.1.4.1.17...
Page 484: Wac
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Trap Name Description vrrpTrapAuthFailure A vrrpAuthFailure trap signifies that a packet has been 1.3.6.1.2.1.68. received from a router whose authentication key or authentication type conflicts with this router's authentication key or authentication type.
Page 485: Appendix D - Radius Attributes Assignment
DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide Appendix D - RADIUS Attributes Assignment The RADIUS Attributes Assignment on the Switch is used in the following modules: Console, Telnet, SSH, Web, 802.1X, MAC-based Access Control, and WAC.
Page 486 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide To assign the 802.1p Default Priority by the RADIUS server, the proper parameters should be configured on the RADIUS server. The table below shows the parameters for 802.1p default priority.
Page 487 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide NOTE: A tag field of greater than 0x1F is interpreted as the first octet of the following field. If the user has configured the VLAN attribute of the RADIUS server (for example, VID 3) and the 802.1X, or MAC based Access Control, or WAC authentication is successful, the port will be assigned to VLAN 3.
Page 488: Appendix E - Ietf Radius Attributes Support
Switch. RADIUS attributes are supported by the IETF standard and Vendor-Specific Attribute (VSA). VSA allows the vendor to create an additionally owned RADIUS attribute. For more information about D-Link VSA, refer to the RADIUS Attributes Assignment Appendix.
Page 489 DGS-3130 Series Layer 3 Stackable Managed Switch Web UI Reference Guide RADIUS Accounting Attributes: Number IETF Attribute User-Name NAS-IP-Address NAS-Port Service-Type Framed-IP-Address Calling-Station-ID NAS-Identifier Acct-Status-Type Acct-Delay-Time Acct-Input-Octets Acct-Output-Octets Acct-Session-ID Acct-Authentic Acct-Session-Time Acct-Input-Packets Acct-Output-Packets Acct-Terminate-Cause Acct-Input-Gigawords Acct-Output-Gigawords NAS-Port-Type NAS-IPv6-Address...

This manual is also suitable for:

Dgs-3130-30ts

D-Link DGS-3130 Series Web Ui Reference Manual

1 Introduction

2 Web-Based Switch Configuration

3 System

4 Management

5 Layer 2 Features

6 Layer 3 Features

7 Quality of Service (Qos)

8 Access Control List (ACL)

9 Security

10 Oam

Quick Links

Related Manuals for D-Link DGS-3130 Series

Summary of Contents for D-Link DGS-3130 Series