[Simul Input Setting] - Panasonic PT-RQ32KE Operating Instructions Manual

[ENABLE]
[DISABLE]
Note
f The backup function is enabled when [BACKUP INPUT MODE] is set to anything other than [OFF] and same signal is input to the primary
input and the secondary input.
f To switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use
the function.
g Set [BACKUP INPUT MODE] to anything other than [OFF].
g Input the same signal to the primary and secondary inputs.
g Display the image of the primary input or secondary input.
f If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to
use the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input or
secondary input.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the combination of that input is displayed in [PRIMARY INPUT] and
[SECONDARY INPUT] of the [BACKUP INPUT SETTING] screen.
f [BACKUP INPUT STATUS] is displayed in the input guide (x page 137) and the [STATUS] screen (x pages 84, 173) when [BACKUP
INPUT MODE] is set to anything other than [OFF].
When the signal can be switched to the backup input signal using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS].
When it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the primary
input is displayed.
The primary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the secondary
input is displayed.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the input is switched seamlessly if the input is switched between the
primary input and the secondary input while it is possible to switch to the backup input signal.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] shows [ACTIVE], the signal is switched to the
backup input if a disruption occurs in the input signal.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], the indication in [BACKUP INPUT STATUS] will change to [INACTIVE] if the input
signal is disrupted and automatically switched to the backup input. In this case, it is not possible to switch to the backup input signal until the
original input signal is restored. If the input has switched to the backup input automatically, it is possible to switch to the backup input signal
when the original signal has restored. In this case, the current input is maintained.
f [BACKUP INPUT SETTING] cannot be set while in the four-screen display mode. The backup operation is not performed either. Set the
[MULTI DISPLAY] menu → [MULTI DISPLAY MODE] to anything other than [OFF] when using the four-screen display mode.
f [BACKUP INPUT MODE] in which the standard SDI input is included as the primary input or the secondary input cannot be selected when
the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] → [SDI IN] is set to anything other than [OFF].
f [BACKUP INPUT MODE] in which the input equipped on the optional Interface Board installed in the slot is included as the primary input or
the secondary input cannot be selected when the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] → [SLOT IN] is set to anything
other than [OFF].
f When [SDI LINK] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT MODE] for that combination cannot
be selected. When [SDI LINK] for the primary input and the secondary input do not match, [BACKUP INPUT MODE] for that combination
cannot be selected.
Match the setting in accordance with the signal and then input the same signal in the primary input and the secondary input.
g The [DISPLAY OPTION] menu → [SDI IN] → [SDI LINK]
g The [DISPLAY OPTION] menu → [SLOT IN] → [SDI LINK]
f When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT
MODE] for that combination cannot be selected. When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the
secondary input do not match, [BACKUP INPUT MODE] for that combination cannot be selected.
Match the setting in accordance with the signal and then input the same signal in the primary input and the secondary input.
g The [DISPLAY OPTION] menu → [SLOT IN] → [HDMI LINK]
g The [DISPLAY OPTION] menu → [SLOT IN] → [DVI-D LINK]
f The primary input setting values are applied to image adjustment values such as the [PICTURE] menu → [PICTURE MODE], [GAMMA],
and [COLOR TEMPERATURE].

[SIMUL INPUT SETTING]

Set this function when the video signal in simultaneous format is input and used.
1) Press as to select [SIMUL INPUT SETTING].
2) Press the <ENTER> button.
f The [SIMUL INPUT SETTING] screen is displayed.
3) Press as to select [SDI IN], [SLOT IN].
f [SLOT IN] can be selected when the optional Interface Board is installed in the slot.
4) Press qw to switch the setting.
f The items will switch each time you press the button.
[OFF]
116 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Switches to the secondary input (primary input) automatically when the input signal for primary input
(secondary input) is disrupted.
Disables the automatic input switching function.
This is not used for simultaneous input.